Always send a stop command at the end of a data transfer.  If we avoid
sending the stop command, some cards remain in data transfer mode, and
refuse to accept further read/write commands.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The MMC layer gives us two parts for the timeout calculation - a fixed
timeout in nanoseconds, and a card clock-speed dependent part.

The PXA MMC hardware allows for a timeout based on the fixed host clock
speed only.  This resulted in some cards being given a short timeout,
and therefore failing to work.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Rather than each driver test MMC_DEBUG itself, and define DEBUG,
pass it in via the makefile instead.

Fix drivers to use pr_debug() where appropriate, and avoid defining
a DEBUG() macro.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

platform_get_irq*() now returns on -ENXIO when the resource cannot be
found.  Ensure all users of platform_get_irq*() handle this error
appropriately.
Signed-off-by: NDavid Vrabel <dvrabel@arcom.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Some hosts need to know the command type, so pass it via a set of
flags in cmd->flags.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This allows us to eliminate the casts in the drivers, and eventually
remove the use of the device_driver function pointer methods for
platform device drivers.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Convert everyone who uses platform_bus_type to include
linux/platform_device.h.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>

In PM v1, all devices were called at SUSPEND_DISABLE level.  Then
all devices were called at SUSPEND_SAVE_STATE level, and finally
SUSPEND_POWER_DOWN level.  However, with PM v2, to maintain
compatibility for platform devices, I arranged for the PM v2
suspend/resume callbacks to call the old PM v1 suspend/resume
callbacks three times with each level in order so that existing
drivers continued to work.

Since this is obsolete infrastructure which is no longer necessary,
we can remove it.  Here's an (untested) patch to do exactly that.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Allow PXA platforms to pass an appropriate delay value to the
PXA MCI driver for delaying detection changes.
Signed-Off-By: NRichard Purdie <rpurdie@rpsys.net>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Change mmc_detect_change() to take a delay argument such that
the detection of card insertions and removals can be delayed
according to the requirements of the host driver or platform.
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add a write protection switch handling code to the PXA MMC driver so
that platform specific code can provide it if available.
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This fixes u32 vs.  pm_message_t in drivers/mmc, drivers/mtd and
drivers/scsi.
Signed-off-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!