This adds a few debugging counters, that are useful for debugging the
"card does not transmit" or "connection is unstable" kind of problems.
It's also useful for tuning an RC algorithm.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Rename the DMA ring pointers to have more descriptive and standard
names. Also remove the 6th unused TX ring. We can add it back later,
if we need it. The unused TX-status rx-ring is also removed, as that's
only used by legacy devices not supported by this driver anyway.

This is no functional change, except less memory allocation for
the removed rings.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds QOS support to the b43 driver.
QOS can be disabled on driver level with a module parameter for debugging purposes.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Reinette pointed out that with the sta_info RCU-ification
the behaviour here changed and the conf_tx callback is
now invoked under RCU read lock. That is not necessary so
this patch restores the original behaviour
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Tested-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add 2413 to srev_names so that it shows up during module load.
This is based on the new patch 7 which did not introduce a helper
on ath5k_hw_reset().

Changes-licensed-under: 3-clause-BSD
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NLuis R. Rodriguez <mcgrof@winlab.rutgers.edu>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Make some changes which mimic what we see in register dumps.
This patch does not add a helper to ath5k_hw_reset(). It
does seem clear we need a re-shuffle around ath5k_hw_reset()
though as code in there is lengthy and already hitting 80-char
limit. This can be dealt with later though.

Changes-licensed-under: ISC
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NLuis R. Rodriguez <mcgrof@winlab.rutgers.edu>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Fix nic_wakeup for PCI-E chips (don't set AR5K_RESET_CTL_PCI bit)

 * Fix dma size setting for PCI-E chips (thanx to Bob Copeland).

Changes-licensed-under: ISC
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NLuis R. Rodriguez <mcgrof@winlab.rutgers.edu>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Since RF2413 it seems that RF_BUFFER settings are different (notice
that the last part -"bank 7" or whatever- is smaller than in 5111/5112).
So until we know what's going on we assume there is no gain optimization
stuff in post-5112 chips.

Changes-licensed-under: ISC
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NLuis R. Rodriguez <mcgrof@winlab.rutgers.edu>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Add AR5K_RF2413 to radio check during hw_reset so it doesn't complain

 * Write ah_phy_spending value we set during attach instead of checking
each time for radio revision

 * Skip txpower setup for RF2413 because it can't transmit with it
(weird thing is that RF5413 has no problem with it).

Changes-licensed-under: ISC
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NLuis R. Rodriguez <mcgrof@winlab.rutgers.edu>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Attach RF2413.

 * Propertly handle different AR5K_PHY_SPENDING settings for each RF
chip by adding a field in ath5k_hw. This way we won't have to check
inside hw_reset (see next patch).

Changes-licensed-under: ISC
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NLuis R. Rodriguez <mcgrof@winlab.rutgers.edu>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* Add initial settings for RF2413

Changes-licensed-under: ISC
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NLuis R. Rodriguez <mcgrof@winlab.rutgers.edu>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Add RF2413 srev values and a new entry on ath5k_radio enum for it
  since it differs from RF5413 (it's not like 5112-2112).

Changes-licensed-under: ISC
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NLuis R. Rodriguez <mcgrof@winlab.rutgers.edu>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The previously unused CR_CAM_MODE register is set to MODE_AP_WDS. This makes the
driver ack mesh (WDS) frames. It does not affect Infra functionality of the
driver.

Previously missing beaconing support has been added. This might also help
implement a currently missing ah-hoc mode.

Support for interrupts from the device have been added, but we are not handling
most of them.

Mesh interfaces are considered associated as long as the interface is up.
Signed-off-by: NLuis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Should be purely cosmetic apart from the removal of the two pointless
MAC addresses.
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The struct enc_key probably wants to die too, but that can come later.
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes reporting rate in RX packets in 52 band.
The rate was updated from CCK rate index instead of OFDM rate 6M
Most of the patch is collateral clean up
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch refactors init geos function. It also fixes few minor bugs.
IWL_MAX_RATE -> IWL_RATE_COUNT (IWL_MAX_RATE included also MCS setting)
There are 9 and 13 rates for 4965 in 2.4 and 5.2 respectively  (rate 60)
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch removes unused variable in iwlYYYY_priv
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds the Gigabit Ethernet driver for the SSB
Gigabit Ethernet core. This driver actually is a frontend to
the Tigon3 driver. So the real work is done by tg3.
This device is used in the Linksys WRT350N.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The mac80211 MLME requires restarting timers after a scan
completes but this wasn't done when hardware scan offload
was added, so add it now.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Tested-by: NBill Moss <bmoss@clemson.edu>
Cc: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Skip properly entries whose dev does not match.
Signed-off-by: NLuis Carlos Cobo <luisca@cozybit.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLuis Carlos Cobo <luisca@cozybit.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLuis Carlos Cobo <luisca@cozybit.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Postponing the deletion is not really useful anymore.
Signed-off-by: NLuis Carlos Cobo <luisca@cozybit.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This avoids dereferencing a no longer existing struct mesh_path.
Signed-off-by: NLuis Carlos Cobo <luisca@cozybit.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLuis Carlos Cobo <luisca@cozybit.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLuis Carlos Cobo <luisca@cozybit.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLuis Carlos Cobo <luisca@cozybit.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Pointed out by Johannes Berg.
Signed-off-by: NLuis Carlos Cobo <luisca@cozybit.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes all the mesh related endianness warnings reported by sparse. As
they were the reason why Johannes marked mesh as BROKEN, that flag has been
removed.
Signed-off-by: NLuis Carlos Cobo <luisca@cozybit.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Today I hit one of my new WARN_ONs in the mac80211 code because
a key wasn't being freed correctly. After wondering for a while
I finally tracked it to the fact that STA keys aren't added to
the per-sdata key list correctly, they are supposed to always be
on that list, not just for default keys. This patch fixes that.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This helps verify that nothing bad is going on in mac80211,
it is unfortunately not possible to implement this generically
in mac80211 easily because there we can't assume that we only
have a single vif which b43 currently can assume.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

I noticed a bug I introduced when mesh is enabled: sta_info_destroy()
will end up calling cancel_timer() on a timer that has never been
initialized because the timer is only initialized in mesh_plink_alloc(),
not in sta_info_alloc(). This patch moves the initialization of all mesh
related fields into sta_info_alloc(), adds a bit of sanity checking to
the cfg80211 handlers and sta_info_insert() and makes mesh_plink_alloc()
a static helper function that is only used from the mesh plink code.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Cc: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Quite a while ago I started this book. The required kernel-doc
patches have since gone into the tree so it is now possible to
build the book in mainline.

The actual documentation is still rather incomplete and not all
things are linked into the book, but this enables us to edit
the documentation collaboratively, hopefully driver authors can
add documentation based on their experience with mac80211.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Luis pointed out that this path is going to be freed right
away anyway so there's no point in assigning next_hop.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Cc: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When we take down an interface, we need to remove the STA info
items that belong to it because otherwise we might invoke a
sta_notify() callback in the driver when we later delete the
STA entries, but in that case the driver will already have
removed its knowledge of the interface they belonged to leading
to confusion. Also, we could invoke the set_tim() callback after
the driver removed its knowledge of the interface, which can
lead to a crash if it requests a beacon with a then-invalid vif
pointer!

A side effect of this patch is that, because it was easier, it
disallows changing the WDS peer while an interface is up. Should
that actually be necessary, it can be added back, but the WDS
peer STA entry may not be added while the interface is UP so for
now I've simplified the WDS peer's STA entry lifetime management.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch cleans up the sta_info struct and documents how
each set of variables is locked. Notably, flags locking is
completely missing. It also adds kernel-doc for some (but
not all yet) members of the struct.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

sta_info_add() has two functions: allocating a station info
structure and inserting it into the hash table/list. Splitting
these two functions allows allocating with GFP_KERNEL in many
places instead of GFP_ATOMIC which is now required by the RCU
protection. Additionally, in many places RCU protection is now
no longer needed at all because between sta_info_alloc() and
sta_info_insert() the caller owns the structure.

This fixes a few race conditions with setting initial flags
and similar, but not all (see comments in ieee80211_sta.c and
cfg.c). More documentation on the existing races will be in
a follow-up patch.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>