drivers/net/ethernet/marvell/skge.c:4046: warning: ‘skge_suspend’ defined but not used
drivers/net/ethernet/marvell/skge.c:4071: warning: ‘skge_resume’ defined but not used
Signed-off-by: NDaniel Halperin <dhalperi@cs.washington.edu>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver uses a shared pool for both rx and tx descriptors.
During open it queues fixed number of 128 descriptors for receive
packets. For each received packet it tries to queue another
descriptor. If this fails the descriptor is lost for rx.
The driver has no limitation on tx descriptors to use, so it
can happen during a nmap / ping -f attack that the driver
allocates all descriptors for tx and looses all rx descriptors.
The driver stops working then.
To fix this limit the number of tx descriptors used to half of
the descriptors available, the rx path uses the other half.

Tested on a custom board using nmap / ping -f to the board from
two different hosts.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Showing which capabilities are not passed to VF
when executing QUERY_PORT
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mtt range was allocated in mtt units but deallocated
in segments. Among the rest, this caused crash during hotplug removal
Reported-by: NYinghai Lu <yinghai@kernel.org>
Signed-off-by: NMarcel Apfelbaum <marcela@mellanox.co.il>
Reviewed-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Tested-by: NYinghai Lu <yinghai@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If slave device already has a receive handler registered, then the
error unwind of bonding device enslave function is broken.

The following will leave a pointer to freed memory in the slave
device list, causing a later kernel panic.
# modprobe dummy
# ip li add dummy0-1 link dummy0 type macvlan
# modprobe bonding
# echo +dummy0 >/sys/class/net/bond0/bonding/slaves

The fix is to detach the slave (which removes it from the list)
in the unwind path.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Reviewed-by: NNicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rx mode should be reset after resming, so unconditionally updating rx
mode rather than conditionally updating based on the value we
remembered, otherwise unexpected value may be used by the nic after
resuming.

btw. I find and test this when debugging guest hibernation in qemu, as
I did not have a 8139cp card in hand, this patch is untested in a
physical 8139cp card, plase review it carefully.
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

delay_eeprom() use long read for Cfg9346 register(offset 0x50) which may read
into the area of reserved register(offset 0x53). Use byte read instead.
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This device uses an already existing DevID but since it supports
WoL we need to add the Sub DevID.  It's support of WoL is limited
to the first port.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Support for new 82599 based quad port adapter.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

I2C access is timing critical. Always do a write flush after writing
to the I2CCTL register.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Saw typo in one message, so decided to run spell checker.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Fix some register reads that had the opcode and register parameters swapped.
Also use define instead of a magic (0x3) number.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Added pause flag for bi-directional flow control advertising to ethtool
settings.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch is meant to address possible issues with the IXGBEVF register
defines generating incorrect values when given a complex expression for the
register offset.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The current gspca core code has a regression where it no longer properly
falls back to lower alt settings when there is not enough bandwidth.

This causes many iso based usb-1 cameras to not work when plugged into a
usb2 hub or a sandybridge chipset motherboard!

This patch fixes this.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Restore skge hardware registers for multicast filtering to their
appropriate values after system resume and after hardware restarts
that are done when changing certain settings.
Signed-off-by: NFlorian Zumbiehl <florz@florz.de>
Acked-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

be2net gets an async link status notification from the FW when it creates
an MCC queue. There are some cases in which this gratuitous notification
is not received from FW. To cover this explicitly query the link status
in be_open().
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1) fix be_vlan_add/rem_vid to return proper status
2) perform appropriate housekeeping if firmware command succeeds.
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Caused loss of connectivity when changing ring size.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The new iso bandwidth calculation code accidentally has broken support
for bulk mode cameras. This has broken the following drivers:
finepix, jeilinj, ovfx2, ov534, ov534_9, se401, sq905, sq905c, sq930x,
stv0680, vicam.

Thix patch fixes this. Fix tested with: se401, sq905, sq905c, stv0680 & vicam
cams.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Michael S. Tsirkin also noticed that we could run the refill work
multiple CPUs: if we kick off a refill on one CPU and then on another,
they would both manipulate the queue at the same time (they use
napi_disable to avoid racing against the receive handler itself).

Tejun points out that this is what the WQ_NON_REENTRANT flag is for,
and that there is a convenient system kthread we can use.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Michael S. Tsirkin noticed that we could run the refill work after
ndo_close, which can re-enable napi - we don't disable it until
virtnet_remove.  This is clearly wrong, so move the workqueue control
to ndo_open and ndo_stop (aka. virtnet_open and virtnet_close).

One subtle point: virtnet_probe() could simply fail if it couldn't
allocate a receive buffer, but that's less polite in virtnet_open() so
we schedule a refill as we do in the normal receive path if we run out
of memory.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

At the moment VFs can only operate in Eth mode.
In addition we don't want the VF to attempt link sensing,
so we block this option as well.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixing wrong register offset which is used to retrieve the number of buttons
attached to the hardware.
Signed-off-by: NTai-hwa Liang <avatar@sentelic.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

On extensive NFS boots on a mx6qsabrelite board it was noted that "FEC: MDIO read timeout" were occuring,
which caused failure on loading the FEC driver.

The original FEC_MII_TIMEOUT was set to 1 ms, which is too low when passed to the usecs_to_jiffies macro.

On ARM one jiffy is 10ms, so use a timeout of 30ms, which corresponds to 3 jiffies.

After running extensive NFS boots, the MDIO timeouts do not occur anymore with this change.
Signed-off-by: NRogerio Pimentel <rogerio.pimentel@freescale.com>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Redhat Bugzilla: Bug 727875 - TCO_EN bit is disabled by TCO driver

The previous patch breaks reset watchdog behaviour on the older hardware.
It is therefor better to make sure that the behaviour for older hardware (<=ICH5 or
6300ESB) is preserved and that the behaviour for newer hardware is changed.
We therefor use the iTCO_version to see if we need the clearing of the SMI_TCO_EN
bit in the SMI_EN register.

So the new behaviour becomes:
turn_SMI_watchdog_clear_off=0 -> Do not turn off SMI clearing watchdog.
turn_SMI_watchdog_clear_off=1 -> Turn off SMI clearing watchdog when iTCO_version=1
				 (ICHO till ICH5 + 6300ESB only)
turn_SMI_watchdog_clear_off=2 -> Turn off SMI clearing watchdog.
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

SGI IP32 (O2)'s ethernet driver (meth) lacks a set_rx_mode function, which
prevents IPv6 from working completely because any ICMPv6 neighbor
solicitation requests aren't picked up by the driver.  So the machine can
ping out and connect to other systems, but other systems will have a very
hard time connecting to the O2.
Signed-off-by: NJoshua Kinard <kumba@gentoo.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix allyesconfig build on architectures without IOMEM:

drivers/net/ethernet/calxeda/xgmac.c:1800:2:
  error: implicit declaration of function 'iounmap' [-Werror=implicit-function-declaration]
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Acked-by: NRob Herring <rob.herring@calxeda.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RC6 fails again.

> I found my system freeze mostly during starting up X and KDE. Sometimes it
> works for some minutes, sometimes it freezes immediatly. When the freeze
> happens, everything is dead (even the reset button does not work, I need to
> power cycle).

> I disabled RC6, and my system runs wonderfully.

> The system is a Z68 Pro board with Sandybridge i5-2500K processor, 8
> GB of RAM and UEFI firmware.
Reported-by: NKai Krakow <hurikhan77@gmail.com>
Signed-off-by: NKeith Packard <keithp@keithp.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Semaphores still cause problems on some machines:

> From Udo Steinberg:
>
> With Linux-3.2-rc6 I'm frequently seeing GPU hangs when large amounts of
> text scroll in an xterm, such as when extracting a tar archive. Such as this
> one (note the timestamps):
>
>  I can reproduce it fairly easily with something
>  as simple as:
>
>	  while true; do dmesg; done

This patch turns them off on SNB while leaving them on for IVB.
Reported-by: NUdo Steinberg <udo@hypervisor.org>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Eugeni Dodonov <eugeni@dodonov.net>
Signed-off-by: NKeith Packard <keithp@keithp.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Include linux/slab.h to fix below build error:

  CC      drivers/net/ethernet/mellanox/mlx4/resource_tracker.o
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c: In function 'mlx4_init_resource_tracker':
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:233: error: implicit declaration of function 'kzalloc'
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:234: warning: assignment makes pointer from integer without a cast
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c: In function 'mlx4_free_resource_tracker':
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:264: error: implicit declaration of function 'kfree'
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c: In function 'alloc_qp_tr':
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:370: warning: assignment makes pointer from integer without a cast
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c: In function 'alloc_mtt_tr':
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:386: warning: assignment makes pointer from integer without a cast
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c: In function 'alloc_mpt_tr':
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:402: warning: assignment makes pointer from integer without a cast
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c: In function 'alloc_eq_tr':
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:417: warning: assignment makes pointer from integer without a cast
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c: In function 'alloc_cq_tr':
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:431: warning: assignment makes pointer from integer without a cast
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c: In function 'alloc_srq_tr':
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:446: warning: assignment makes pointer from integer without a cast
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c: In function 'alloc_counter_tr':
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:461: warning: assignment makes pointer from integer without a cast
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c: In function 'add_res_range':
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:521: warning: assignment makes pointer from integer without a cast
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c: In function 'mac_add_to_slave':
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:1193: warning: assignment makes pointer from integer without a cast
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c: In function 'add_mcg_res':
drivers/net/ethernet/mellanox/mlx4/resource_tracker.c:2521: warning: assignment makes pointer from integer without a cast
make[5]: *** [drivers/net/ethernet/mellanox/mlx4/resource_tracker.o] Error 1
make[4]: *** [drivers/net/ethernet/mellanox/mlx4] Error 2
make[3]: *** [drivers/net/ethernet/mellanox] Error 2
make[2]: *** [drivers/net/ethernet] Error 2
make[1]: *** [drivers/net] Error 2
make: *** [drivers] Error 2
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch makes use of the set_memory_x() kernel API in order
to make necessary BIOS calls to source NMIs.

This is needed for SLES11 SP2 and the latest upstream kernel as it appears
the NX Execute Disable has grown in its control.

Signed-off by: Thomas Mingarelli <thomas.mingarelli@hp.com>
Signed-off by: Wim Van Sebroeck <wim@iguana.be>
Cc: stable@kernel.org

The AMBA ID table is marked as __initdata, yet it is referenced by the
driver struct which is not.  This causes a (somewhat unhelpful) section
mismatch warning:

  WARNING: drivers/watchdog/sp805_wdt.o(.data+0x4c): Section mismatch in
           reference from the variable sp805_wdt_driver to the (unknown
           reference) .init.data:(unknown)

Fix this by removing the annotation.
Signed-off-by: NNick Bowler <nbowler@elliptictech.com>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

The state holders used in the PM path of the drivers report as
unused variables when compiling without CONFIG_PM so let's
move them inside CONFIG_PM.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

We recently made loopback a bool type instead of an int, so the bitwise
AND is redundent.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixed the asix_get_wol() routine reported wrong wol status issue.
Signed-off-by: NAllan Chou <allan@asix.com.tw>
Tested-by: NEugene &lt;elubarsky@gmail.com&gt;; Allan Chou <allan@asix.com.tw>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change details:
	- Add debugfs support to obtain firmware trace, saved firmware trace on
	  an IOC crash, driver info and read/write to registers.

	- debugfs hierarchy:
	  bna/pci_dev:<pci_name>
	  where the pci_name corresponds to the one under /sys/bus/pci/drivers/bna

	- Following are the new debugfs entries added:
	  fwtrc: collect current firmware trace.
	  fwsave: collect last saved fw trace as a result of firmware crash.
	  regwr: write one word to chip register
	  regrd: read one or more words from chip register.
	  drvinfo: collect the driver information.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change details:
	- The patch adds flash sub-module to the bna driver.
	- Added ethtool set_eeprom() and get_eeprom() entry points to
	  support flash partition read/write operations.
Signed-off-by: NKrishna Gudipati <kgudipat@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>