Changes to support MPEG TS on VIDB
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Reviewed-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Changes to support interrupts on VIDB
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Reviewed-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- define missing register bit values for VID_B
- corrected VID/VBI_B_GPCNT_CTL register addresses
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

start_dma() would fail to start dma if a device used VIDB (portb).
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Reviewed-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The switch() statement is no longer required.
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Reviewed-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The HVR1250 and HVR1800 boards need the s5h1409 demod GPIO enabled.
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Reviewed-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Not sure why they are there, but they don't do anything now.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Use the balance control to make the mono volume control stereo.

Note that full range isn't supported.  The balance control attenuates one
channel by 0 to -63 dB, and the volume control provides additional attenuation
to both channels by another 0 to -63 dB.

So the channel with the most attenuation has a range of 0 to -126 dB, while
the other channel only has a range of 0 to -63 dB.  ALSA volume controls don't
appear to support this concept.  I just limited the range to 0 to -63 total.
Once you get to -63 dB, you're already at silence, so additional attenuation
is pretty much pointless anyway.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Auto-load ir-kbd-i2c for ir receiver support, and rtc-isl1208 for rtc 
support for the FusionHDTV5 RT Gold.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Ignore 0x6b and 0x6f on cx88 boards. Some FusionHDTV cards
have an ir receiver at 0x6b and an RTC at 0x6f which can
get corrupted if probed.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Acked-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- fixed missing buttons in keymap.

- make function names & descriptions more generic,
  since this same ir receiver and remote is used in
  many FusionHDTV products.

- miscellaneous cleanups.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This patch adds support for the built-in IR receiver of the DViCO
Fusion HDTV5 RT GOLD PCI card, using FusionHDTV MCE remote controller.
Signed-off-by: NChaogui Zhang <czhang1974@gmail.com>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

I wanted to document the NMI assert issue inside the code, even though
it's already documented in the patch history. If/when the next cx23887
revision appears, is may need to be enabled on that also.
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

A number of Hauppauge boards share the same tuner and demod
configurations. This patch removes duplicate structures.
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Moving some defines into the correct header file.
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Removed unused code.
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Unused code is removed.
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Adding support for the Hauppauge HVR1250 PCIe ATSC board.
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Changed the pci_quirks function to detech the bridge type before setting
the NMI clear bit, rather than detecting based on unique board id.
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The pci_quirks function was being called too early during initialisation,
it needs to be called after the board has been identified.
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Turn off i2c_debug by default, to make the driver less verbose.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The dvb-pll module is not being used by this driver.
Remove the unneeded #include.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Removed if 0'd code, removed cx88 references.
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The mt2131 tuner reports lock even when the hardware should not
lock. This patch allows the s5h1409 demodulator to be configured to query
either the tuner driver for status, or the demodulator status when the
application requests lock status. This avoids returning false CARRIER
and/or SIGNAL lock status.

S5H1409 and MT2131 drivers.  This is the remainder of the changeset, which
only touches cx23885-dvb.c
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Moved the field from cx23885_board to cx23885_dev and added code to
iautomatically set the bridge type based on the pci device id.
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This is required to support the cx258xx family of audio and video decoders.
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The cx23885 and cx23887 family use two different memory maps which govern
how the internal SRAM is configured. This patch streamlines the access to those
structures.
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The sram allocations for the cx23887 differ slightly from the cx23885.
This patch modifies the cx23887 specific sram memory map to reflect this.
As a result, interrupts and DMA handling have also been enabled in
cx23885_start_dma() for 887 specific boards.

ATSC streaming is now available on cx23885 and cx23887 bridges.
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

I2C bus 3 was being initialised with the incorrect address register.
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

- fix #include for <media/video-buf-dvb.h>
- fix cx23885_irq declaration for 2.6.19 and later
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This is a new framework to support boards based on the CX23885/7 PCIe
bridge. The framework supports digital (no analog yet)
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Fix the following build warning:

 CC [M]  cx25840-core.o

cx25840-core.c: In function 'init_dll1':
cx25840-core.c:147: warning: implicit declaration of function 'udelay'
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>