RX_WATER_MARK sets the number of locations in Rx FIFO that can be used before
the transport layer instructs the link layer to transmit HOLDS. Note that it
can take some time for the HOLDs to get to the other end, and that in the
interim there must be enough room in the FIFO to absorb all data that could
arrive.

Update the new recommended value to 16.
Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

When a single device error is detected, the device under the error
is indicated by the error bit set in the DER. There is a one to one
mapping between register bit and devices on Port multiplier(PMP)
i.e. bit 0 represents PMP device 0 and bit 1 represents PMP device
1 etc.

Current implementation treats Device error register value as device
number not set of bits representing multiple device on PMP. It is
changed to consider bit level.

No need to check for each set bit as all command is going to be
aborted.
Signed-off-by: NAshish Kalra <B00888@freescale.com>
Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

As per SAT-3 the WWN ID should be included in the VPD page 0x83
(device identification) emulation.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Acked-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Some DMA controllers (eg: drivers/dma/dw_dmac*) allow platform specific
configuration for dma transfers. User drivers need to set chan->private field
of channel with pointer to configuration data. This patch takes dma_priv data
from platform data and passes it to chan->private_data, in order to pass
platform specific configuration to DMAC controller.
Signed-off-by: NViresh Kumar <viresh.kumar@st.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Commit 40d69ba0
("pata_hpt{37x|3x2n}: use pr_*(DRV_NAME ...) instead of printk(KERN_* ...)")
used pr_<level>.

Add #define pr_fmt and remove DRV_NAME.
Increment driver version numbers.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The Arasan CompactFlash Device Controller has three basic modes of
operation: PC card ATA using I/O mode, PC card ATA using memory mode, PC card
ATA using true IDE modes.

Currently driver supports only True IDE mode.
Signed-off-by: NViresh Kumar <viresh.kumar@st.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

This patch adds ata_sff_queue_work() & ata_sff_queue_delayed_work() routine in
libata-sff.c file. This routine can be used by ata drivers to use ata_sff_wq.
Signed-off-by: NViresh Kumar <viresh.kumar@st.com>
Acked-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

This patch adds an updated SATA RAID DeviceID for the Intel Patsburg PCH.
Signed-off-by: NSeth Heasley <seth.heasley@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Recognize Marvell 88SE9125 PCIe SATA 6.0 Gb/s controller.
Signed-off-by: NPer Jessen <per@computer.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Commit 6b7ae954 (libata: reimplement link power
management) removed the check of ATA_FLAG_LPM but neglected to remove the flag
itself.  Do it now...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

All checks of ATA_FLAG_NO_LEGACY have been removed by the commits
c791c306 ([libata] minor PCI IDE probe
fixes and cleanups) and f0d36efd (libata:
update libata core layer to use devres), so I think it's time to finally
get rid of this flag...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Commit 0d5ff566 (libata: convert to iomap)
removed all checks of ATA_FLAG_MMIO but neglected to remove the flag itself.
Do it now, at last...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

These flags are marked as obsolete and the checks for them have been removed
by commit 29444088 (libata-sff: kill unused
ata_bus_reset()), so I think it's time to finally get rid of them...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Commit 14bdef98 ([libata] convert drivers to
use ata.h mode mask defines) didn't convert these two libata driver outside
drivers/ata/...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The driver makes use of the two options (CONFIG_SATA_DWC_[V]DEBUG) to enable
the debug output but they both are absent in drivers/ata/Kconfig...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The driver erroneously uses ata_get_cmd_descript() not only for printing out
the ATA commands but also the protocol and DMA direction enums. Add functions
for properly printing those out...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The caller expects this function to return the DMA channel number on success,
while it returns 0...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Fix the following compilation errors/warnings:

drivers/ata/sata_dwc_460ex.c:43:1: warning: "DRV_NAME" redefined
In file included from drivers/ata/sata_dwc_460ex.c:38:
drivers/ata/libata.h:31:1: warning: this is the location of the previous
definition
drivers/ata/sata_dwc_460ex.c:44:1: warning: "DRV_VERSION" redefined
drivers/ata/libata.h:32:1: warning: this is the location of the previous
definition
drivers/ata/sata_dwc_460ex.c: In function `sata_dwc_exec_command_by_tag':
drivers/ata/sata_dwc_460ex.c:1356: warning: passing argument 1 of
`ata_get_cmd_descript' makes integer from pointer without a cast
drivers/ata/sata_dwc_460ex.c: In function `sata_dwc_qc_issue':
drivers/ata/sata_dwc_460ex.c:1476: warning: `err' is used uninitialized in this
function
drivers/ata/sata_dwc_460ex.c:1465: note: `err' was declared here
drivers/ata/sata_dwc_460ex.c: In function `sata_dwc_qc_issue':
drivers/ata/sata_dwc_460ex.c:1493: warning: passing argument 1 of
`ata_get_cmd_descript' makes integer from pointer without a cast
drivers/ata/sata_dwc_460ex.c: In function `sata_dwc_qc_prep':
drivers/ata/sata_dwc_460ex.c:1537: error: `tag' undeclared (first use in this
function)
drivers/ata/sata_dwc_460ex.c:1537: error: (Each undeclared identifier is
reported only once
drivers/ata/sata_dwc_460ex.c:1537: error: for each function it appears in.)

NB: error only happens if DEBUG_NCQ macro is defined...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Somehow the driver was committed with a bare number for the PIO mask, instead
of ATA_PIO4...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The conversion is quite complex given that the libata new error
handler has to be hooked into the current libsas timeout and error
handling.  The way this is done is to process all the failed commands
via libsas first, but if they have no underlying sas task (and they're
on a sata device) assume they are destined for the libata error
handler and send them accordingly.

Finally, activate the port recovery of the libata error handler for
each port known to the host.  This is somewhat suboptimal, since that
port may not need recovering, but given the current architecture of
the libata error handler, it's the only way; and the spurious
activation is harmless.
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Right at the moment, the libata error handler is incredibly
monolithic.  This makes it impossible to use from composite drivers
like libsas and ipr which have to handle error themselves in the first
instance.

The essence of the change is to split the monolithic error handler
into two components: one which handles a queue of ata commands for
processing and the other which handles the back end of readying a
port.  This allows the upper error handler fine grained control in
calling libsas functions (and making sure they only get called for ATA
commands whose lower errors have been fixed up).
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The SCSI host eh_cmd_q should be protected by the host lock (not the
port lock).  This probably doesn't matter that much at the moment,
since we try to serialise the add and eh pieces, but it might matter
in future for more convenient error handling.  Plus this switches
libata to the standard eh pattern where you lock, remove from the cmd
queue to a local list and unlock and then operate on the local list.
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

For historical reasons, libsas uses the scsi host lock as the ata port
lock, and libata always uses the ata host.  For the old eh, this was
largely irrelevant since the two locks were never mixed inside the
code.  However, the new eh has a case where it nests acquisition of
the host lock inside the port lock (this does look rather deadlock
prone).  Obviously this would be an instant deadlock if the port lock
were the host lock, so switch the libsas paths to use the ata host
lock as well.
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The function ata_sas_port_init() has always really done its own thing.
However, as a precursor to moving to the libata new eh, it has to be
properly using the standard libata scan paths.  This means separating
the current libata scan paths into pieces which can be shared with
libsas and pieces which cant (really just the async call and the host
scan).
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

ata_eh_analyze_serror() suppresses hotplug notifications if LPM is
being used because LPM generates spurious hotplug events.  It compared
whether link->lpm_policy was different from ATA_LPM_MAX_POWER to
determine whether LPM is enabled; however, this is incorrect as for
drivers which don't implement LPM, lpm_policy is always
ATA_LPM_UNKNOWN.  This disabled hotplug detection for all drivers
which don't implement LPM.

Fix it by comparing whether lpm_policy is greater than
ATA_LPM_MAX_POWER.
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: stable@kernel.org
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging:
  hwmon: (adt7411) add MODULE_DEVICE_TABLE
  hwmon: (ad7414) add MODULE_DEVICE_TABLE

Fix new kernel-doc warning in fs/block_dev.c:

Warning(fs/block_dev.c:937): No description found for parameter 'kill_dirty'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Several ACPI drivers fail to build if CONFIG_NET is unset, because
they refer to things depending on CONFIG_THERMAL that in turn depends
on CONFIG_NET.  However, CONFIG_THERMAL doesn't really need to depend
on CONFIG_NET, because the only part of it requiring CONFIG_NET is
the netlink interface in thermal_sys.c.

Put the netlink interface in thermal_sys.c under #ifdef CONFIG_NET
and remove the dependency of CONFIG_THERMAL on CONFIG_NET from
drivers/thermal/Kconfig.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NRandy Dunlap <randy.dunlap@oracle.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Len Brown <lenb@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Luming Yu <luming.yu@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm: fix unsigned vs signed comparison issue in modeset ctl ioctl.
  drm/nv50-nvc0: make sure vma is definitely unmapped when destroying bo

Merge branch 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6

* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
  omap4: prcm: Fix the CPUx clockdomain offsets
  OMAP2+: clocksource: fix crash on boot when !CONFIG_OMAP_32K_TIMER
  OMAP2/3: clock: fix fint calculation for DPLL_FREQSEL
  OMAP2+: mailbox: fix lookups for multiple mailboxes
  OMAP2420: mailbox: fix IVA vs DSP IRQ numbering
  mach-omap2: smartreflex: world-writable debugfs voltage files
  mach-omap2: pm: world-writable debugfs timer files
  mach-omap2: mux: world-writable debugfs files

Merge branches 'perf-fixes-for-linus', 'x86-fixes-for-linus' and 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  perf timechart: Fix max number of cpus
  perf timechart: Fix black idle boxes in the title
  perf hists: Print number of samples, not the period sum

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86: Use u32 instead of long to set reset vector back to 0

* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  clockevents: Prevent oneshot mode when broadcast device is periodic

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
  fuse: fix truncate after open
  fuse: fix hang of single threaded fuseblk filesystem

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2:
  ocfs2: Check heartbeat mode for kernel stacks only
  Ocfs2/refcounttree: Fix a bug for refcounttree to writeback clusters in a right number.
  ocfs2: Fix estimate of necessary credits for mkdir

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  eukrea-tlv320: fix platform_name
  ASoC: correct pxa AC97 DAI names
  ALSA: hda - Add support for new IDT 92HD98 and 92HD99 codecs
  ALSA: HDA: Add ideapad quirk for two Dell machines
  ALSA: HDA: Add a new Conexant codec 506e (20590)
  ALSA: usb-audio: fix oops due to cleanup race when disconnecting
  ASoC: Hook wm_hubs micbiases up to CLK_SYS
  ASoC: Correct definition of WM8903_VMID_RES_5K
  ASoC: Fix WM8958 default microphone detection argument ordering
  ALSA: HDA: Fix mic initialization in VIA auto parser
  ALSA: fix one memory leak in sound jack

Commit e2cda322 ("thp: add pmd mangling generic functions") replaced
some macros in <asm-generic/pgtable.h> with inline functions.

If the functions are to be defined (not all architectures need them)
then struct vm_area_struct must be defined first.  So include
<linux/mm_types.h>.

Fixes a build failure seen in Debian:

    CC [M]  drivers/media/dvb/mantis/mantis_pci.o
  In file included from arch/arm/include/asm/pgtable.h:460,
                   from drivers/media/dvb/mantis/mantis_pci.c:25:
  include/asm-generic/pgtable.h: In function 'ptep_test_and_clear_young':
  include/asm-generic/pgtable.h:29: error: dereferencing pointer to incomplete type
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

A customer of ours, complained that when setting the reset
vector back to 0, it trashed other data and hung their box.
They noticed when only 4 bytes were set to 0 instead of 8,
everything worked correctly.

Mathew pointed out:

 |
 | We're supposed to be resetting trampoline_phys_low and
 | trampoline_phys_high here, which are two 16-bit values.
 | Writing 64 bits is definitely going to overwrite space
 | that we're not supposed to be touching.
 |

So limit the area modified to u32.
Signed-off-by: NDon Zickus <dzickus@redhat.com>
Acked-by: NMatthew Garrett <mjg@redhat.com>
Cc: <stable@kernel.org>
LKML-Reference: <1297139100-424-1-git-send-email-dzickus@redhat.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Currently numcpus is determined in pid_put_sample which is only
called on sched_switch/sched_wakeup sample processing.

On a machine with a lot cpus I often saw the last cpu missing.

Check for (max) numcpus on every event happening and in the
beginning. -> fixes the issue for me.
Signed-off-by: NThomas Renninger <trenn@suse.de>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Cc: lenb@kernel.org
LKML-Reference: <1298842606-55712-6-git-send-email-trenn@suse.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

This fix is needed for eye of gnome and firefox svg viewers.
Only Inkscape can handle the broken case.

Compare with the other svg_legenda_box declarations, looks
like a typo slipped in at this place.
Signed-off-by: NThomas Renninger <trenn@suse.de>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Cc: lenb@kernel.org
LKML-Reference: <1298842606-55712-5-git-send-email-trenn@suse.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>