This patch adds the core module of the MOST driver to the kernel's driver
staging area. This module is part of the MOST driver and handles the
configuration interface in sysfs, the buffer management and the data
routing.

MOST defines the protocol, hardware and software layers necessary to allow
for the efficient and low-cost transport of control, real-time and packet
data using a single medium (physical layer). Media currently in use are
fiber optics, unshielded twisted pair cables (UTP) and coax cables. MOST
also supports various speed grades up to 150 Mbps.
For more information on MOST, visit the MOST Cooperation website:
www.mostcooperation.com.

Cars continue to evolve into sophisticated consumer electronics platforms,
increasing the demand for reliable and simple solutions to support audio,
video and data communications. MOST can be used to connect multiple
consumer devices via optical or electrical physical layers directly to one
another or in a network configuration. As a synchronous network, MOST
provides excellent Quality of Service and seamless connectivity for
audio/video streaming. Therefore, the driver perfectly fits to the mission
of Automotive Grade Linux to create open source software solutions for
automotive applications.

The driver consists basically of three layers. The hardware layer, the
core layer and the application layer. The core layer consists of the core
module only. This module handles the communication flow through all three
layers, the configuration of the driver, the configuration interface
representation in sysfs, and the buffer management.
For each of the other two layers a selection of modules is provided. These
modules can arbitrarily be combined to meet the needs of the desired
system architecture. A module of the hardware layer is referred to as an
HDM (hardware dependent module). Each module of this layer handles exactly
one of the peripheral interfaces of a network interface controller (e.g.
USB, MediaLB, I2C). A module of the application layer is referred to as an
AIM (application interfacing module). The modules of this layer give access
to MOST via one the following ways: character devices, ALSA, Networking or
V4L2.

To physically access MOST, an Intelligent Network Interface Controller
(INIC) is needed. For more information on available controllers visit:
www.microchip.com
Signed-off-by: NChristian Gromm <christian.gromm@microchip.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

After IO partition recovery, it was possible to get into a situation where
a visornic device would repeatedly report:

    NETDEV WATCHDOG: eth0 (): transmit queue 0 timed out

The actual problem would affect any visornic device that was rapidly
transmitting at the same time the IO partition was being recovered. Once
you hit the problem, the only way to resume use of the nic would be to
reboot the Linux client partition.

The problem was caused by chstat.sent_xmit and chstat.got_xmit_done NOT
getting cleared during IO partition recovery. This is necessary because
outstanding xmits would essentially be "abandoned" during such recovery.
These fields are now cleared in virtnic_serverdown_complete().
Signed-off-by: NTim Sell <Timothy.Sell@unisys.com>
Signed-off-by: NBenjamin Romer <benjamin.romer@unisys.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Logic to check for failures of visorchannel_signalinsert() and
visorchannel_signalremove() were added, and a new sent_post_failed counter
tracks the number of times we failed to post a rcv buffer to the IO
partition.
Signed-off-by: NTim Sell <Timothy.Sell@unisys.com>
Signed-off-by: NBenjamin Romer <benjamin.romer@unisys.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

visornic tx reset handling is done asynchronously via a workqueue in
visornic_timeout_reset().  As a result, it needs to use rtnl_lock() /
rtnl_unlock() to lock against possible simultaneous close() of the network
device.

(I consulted the bnx2 driver as a model here, as that driver also does
its tx reset handling asynchronously, just like visornic does.  See
bnx2_tx_timeout() and bnx2_reset_task().)
Signed-off-by: NTim Sell <Timothy.Sell@unisys.com>
Signed-off-by: NBenjamin Romer <benjamin.romer@unisys.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When s-Par is in polling mode it checks every 2 ms to see if there is
a response from the IO service partition in the queue. Currently it
just reads one entry per 2 ms, this needs to be changed so it drains
the queue on each check.
Signed-off-by: NDavid Kershner <david.kershner@unisys.com>
Signed-off-by: NBenjamin Romer <benjamin.romer@unisys.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Flag is never set. Remove it and the code that is dead because of it.
Signed-off-by: NJakub Sitnicki <jsitnicki@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Refactored rtw_free_assoc_resources to avoid sparse warnings about
different contexts for basic lock
Signed-off-by: NBuţiu Alexandru Octavian <predator5047@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove macro and use explicit case statements. Code is a little
longer but clearer. Checkpatch.pl does not complain anymore.
Signed-off-by: NIoan-Adrian Ratiu <adi@adirat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The return value of the `cmdtest` handler for a subdevice checks the
prospective new command in various steps and returns the step number at
which any problem was detected, or 0 if no problem was detected.  It is
allowed to modify the command in various ways at each step.  Corrections
for out-of-range values are generally made at step 3, and minor
adjustments such as rounding are generally made at step 4.

The `cmdtest` handler for the AO subdevice (`usbduxsigma_ao_cmdtest()`)
currently range checks the timings at step 3.  Since the running command
will round down the timings, add code to round them down at step 4.
Signed-off-by: NIan Abbott <abbotti@mev.co.uk>
Reviewed-by: NBernd Porr <mail@berndporr.me.uk>
Reviewed-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The `cmdtest` and `cmd` handlers for the AO subdevice
(`usbduxsigma_ao_cmdtest()` and `usbduxsigma_ao_cmd()`) support "scan"
timing of commands with all channels updated every "scan" period.  There
is some disabled code to use "convert" timing in high speed mode.  That
would allow channels to be updated sequentially every "convert" period.
Since that code is incomplete and currently disabled, remove it to
simplify the existing code.
Signed-off-by: NIan Abbott <abbotti@mev.co.uk>
Reviewed-by: NBernd Porr <mail@berndporr.me.uk>
Reviewed-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The return value of the `cmdtest` handler for a subdevice checks the
prospective new command in various steps and returns the step number at
which any problem was detected, or 0 if no problem was detected.  It is
allowed to modify the command in various ways at each step.  Corrections
for out-of-range values are generally made at step 3, and minor
adjustments such as rounding are generally made at step 4.

The `cmdtest` handler for the AI subdevice (`usbduxsigma_ai_cmdtest()`)
currently modifies `cmd->scan_begin_arg` to bring it into range and
round it down at step 3.  Move the rounding down part to step 4 to
follow the usual Comedi convention.
Signed-off-by: NIan Abbott <abbotti@mev.co.uk>
Reviewed-by: NBernd Porr <mail@berndporr.me.uk>
Reviewed-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The AI subdevice `cmdtest` handler `usbduxsigma_ai_cmdtest()` ensures
that `cmd->scan_begin_src == TRIG_TIMER` by the end of step 2 of the
command checking code, so assume that this is the case for step 3
onwards and remove the redundant code.
Signed-off-by: NIan Abbott <abbotti@mev.co.uk>
Reviewed-by: NBernd Porr <mail@berndporr.me.uk>
Reviewed-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

`devpriv->ao_timer` is used while an asynchronous command is running on
the AO subdevice.  It also gets modified by the subdevice's `cmdtest`
handler for checking new asynchronous commands,
`usbduxsigma_ao_cmdtest()`, which is not correct as it's allowed to
check new commands while an old command is still running.  Fix it by
moving the code which sets up `devpriv->ao_timer` into the subdevice's
`cmd` handler, `usbduxsigma_ao_cmd()`.

Note that the removed code in `usbduxsigma_ao_cmdtest()` checked that
`devpriv->ao_timer` did not end up less that 1, but that could not
happen due because `cmd->scan_begin_arg` or `cmd->convert_arg` had
already been range-checked.

Also note that we tested the `high_speed` variable in the old code, but
that is currently always 0 and means that we always use "scan" timing
(`cmd->scan_begin_src == TRIG_TIMER` and `cmd->convert_src == TRIG_NOW`)
and never "convert" (individual sample) timing (`cmd->scan_begin_src ==
TRIG_FOLLOW` and `cmd->convert_src == TRIG_TIMER`).  The moved code
tests `cmd->convert_src` instead to decide whether "scan" or "convert"
timing is being used, although currently only "scan" timing is
supported.

Fixes: fb1ef622 ("staging: comedi: usbduxsigma: tidy up analog output command support")
Signed-off-by: NIan Abbott <abbotti@mev.co.uk>
Reviewed-by: NBernd Porr <mail@berndporr.me.uk>
Reviewed-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: <stable@vger.kernel.org> # 3.19 onwards
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

`devpriv->ai_timer` is used while an asynchronous command is running on
the AI subdevice.  It also gets modified by the subdevice's `cmdtest`
handler for checking new asynchronous commands
(`usbduxsigma_ai_cmdtest()`), which is not correct as it's allowed to
check new commands while an old command is still running.  Fix it by
moving the code which sets up `devpriv->ai_timer` and
`devpriv->ai_interval` into the subdevice's `cmd` handler,
`usbduxsigma_ai_cmd()`.

Note that the removed code in `usbduxsigma_ai_cmdtest()` checked that
`devpriv->ai_timer` did not end up less than than 1, but that could not
happen because `cmd->scan_begin_arg` had already been checked to be at
least the minimum required value (at least when `cmd->scan_begin_src ==
TRIG_TIMER`, which had also been checked to be the case).

Fixes: b986be85 ("staging: comedi: usbduxsigma: tidy up analog input command support)
Signed-off-by: NIan Abbott <abbotti@mev.co.uk>
Reviewed-by: NBernd Porr <mail@berndporr.me.uk>
Reviewed-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: <stable@vger.kernel.org> # 3.19 onwards
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use naming schema found in other rtlwifi devices.
Rename init_hal_dm to rtl92e_dm_init.
Signed-off-by: NMateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use naming schema found in other rtlwifi devices.
Rename init_firmware to rtl92e_init_fw.
Signed-off-by: NMateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use naming schema found in other rtlwifi devices.
Rename rtllib_ips_leave_wq to rtl92e_rtllib_ips_leave_wq.
Signed-off-by: NMateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use naming schema found in other rtlwifi devices.
Rename rtllib_ips_leave to rtl92e_rtllib_ips_leave.
Signed-off-by: NMateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use naming schema found in other rtlwifi devices.
Rename rtl8192_hw_wakeup_wq to rtl92e_hw_wakeup_wq.
Signed-off-by: NMateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use naming schema found in other rtlwifi devices.
Rename rtl8192_hw_wakeup to rtl92e_hw_wakeup.
Signed-off-by: NMateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use naming schema found in other rtlwifi devices.
Rename rtl8192_hw_to_sleep to rtl92e_enter_sleep.
Signed-off-by: NMateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use naming schema found in other rtlwifi devices.
Rename rtl8192_hw_sleep_wq to rtl92e_hw_sleep_wq.
Signed-off-by: NMateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use naming schema found in other rtlwifi devices.
Rename LeisurePSLeave to rtl92e_leisure_ps_leave.
Signed-off-by: NMateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use naming schema found in other rtlwifi devices.
Rename LeisurePSEnter to rtl92e_leisure_ps_enter.
Signed-off-by: NMateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use naming schema found in other rtlwifi devices.
Rename IPSLeave_wq to rtl92e_ips_leave_wq.
Signed-off-by: NMateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use naming schema found in other rtlwifi devices.
Rename IPSLeave to rtl92e_ips_leave.
Signed-off-by: NMateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use naming schema found in other rtlwifi devices.
Rename IPSEnter to rtl92e_ips_enter.
Signed-off-by: NMateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use naming schema found in other rtlwifi devices.
Rename rtl8192E_suspend to rtl92e_suspend.
Signed-off-by: NMateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use naming schema found in other rtlwifi devices.
Rename rtl8192E_resume to rtl92e_resume.
Signed-off-by: NMateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use naming schema found in other rtlwifi devices.
Rename rtl8192_pci_findadapter to rtl92e_check_adapter.
Signed-off-by: NMateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use naming schema found in other rtlwifi devices.
Rename eprom_read to rtl92e_eeprom_read.
Signed-off-by: NMateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use naming schema found in other rtlwifi devices.
Rename init_rate_adaptive to rtl92e_init_adaptive_rate.
Signed-off-by: NMateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use naming schema found in other rtlwifi devices.
Rename hal_dm_watchdog to rtl92e_dm_watchdog.
Signed-off-by: NMateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use naming schema found in other rtlwifi devices.
Rename dm_txpower_trackingcallback to rtl92e_dm_txpower_tracking_wq.
Signed-off-by: NMateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use naming schema found in other rtlwifi devices.
Rename dm_rf_pathcheck_workitemcallback to rtl92e_dm_rf_pathcheck_wq.
Signed-off-by: NMateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use naming schema found in other rtlwifi devices.
Rename dm_restore_dynamic_mechanism_state to rtl92e_dm_restore_state.
Signed-off-by: NMateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use naming schema found in other rtlwifi devices.
Rename dm_initialize_txpower_tracking to rtl92e_dm_init_txpower_tracking.
Signed-off-by: NMateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use naming schema found in other rtlwifi devices.
Rename dm_init_edca_turbo to rtl92e_dm_init_edca_turbo.
Signed-off-by: NMateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use naming schema found in other rtlwifi devices.
Rename dm_cck_txpower_adjust to rtl92e_dm_cck_txpower_adjust.
Signed-off-by: NMateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use naming schema found in other rtlwifi devices.
Rename dm_backup_dynamic_mechanism_state to rtl92e_dm_backup_state.
Signed-off-by: NMateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>