Added support for ASICs that report temperature. Temperature notices are
 reported as events and logged. Temperature can be read via sysfs.
Signed-off-by: NJames Smart <James.Smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Set the default command timeout for ibmvscsi disks to 60 seconds
to ensure we don't prematurely timeout commands. This fixes a problem
seen where the default 30 seconds was not long enough due to
congestion on the server.
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

This patch does some additional cleanups after the 53c7xx removal.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

- convert to use the new accessors for the sg lists and the
parameters.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

 1. Create a file "update_bios" in sysfs to allow user to update bios
    from user space.

 2. The BIOS image file can be downloaded from web site

"http://www.adaptec.com/en-US/downloads/bios_fw/bios_fw_ver?productId=SAS-48300&dn=Adaptec+Serial+Attached+SCSI+48300"
    and copy the BIOS image into /lib/firmware folder.

 3. The aic994xx will accept "update bios_file" and "verify bios_file"
    commands to perform update and verify BIOS image .

    For example:

     Type "echo "update asc483c01.ufi" > /sys/devices/.../update_bios"
          to update BIOS image from /lib/firmware/as483c01.ufi file into
          HBA's flash memory.

     Type "echo "verify asc483c01.ufi" > /sys/devices/.../update_bios"
          to verify BIOS image between /lib/firmware/asc48c01.ufi file
and
          HBA's flash memory.

 4. Type "cat  /sys/devices/.../update_bios" to view the status or
result
    of updating BIOS.
Signed-off-by: NGilbert Wu <gilbert_wu@adaptec.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

This will send for a card reader slot (remove/add media):
  UEVENT[1187091572.155884] change   /devices/pci0000:00/0000:00:1d.7/usb5/5-2/5-2:1.0/host7/target7:0:0/7:0:0:0 (scsi)
  UEVENT[1187091572.162314] remove   /block/sdb/sdb1 (block)
  UEVENT[1187091572.172464] add      /block/sdb/sdb1 (block)
  UEVENT[1187091572.175408] change   /devices/pci0000:00/0000:00:1d.7/usb5/5-2/5-2:1.0/host7/target7:0:0/7:0:0:0 (scsi)

and for a DVD drive (add/eject media):
  UEVENT[1187091590.189159] change   /devices/pci0000:00/0000:00:1f.1/host4/target4:0:0/4:0:0:0 (scsi)
  UEVENT[1187091590.957124] add      /module/isofs (module)
  UEVENT[1187091604.468207] change   /devices/pci0000:00/0000:00:1f.1/host4/target4:0:0/4:0:0:0 (scsi)

Userspace gets events, even for unpartitioned media. This unifies
the event handling for asynchronoous events (AN) and events caused by
perodical polling the device from userspace.
Signed-off-by: NKay Sievers <kay.sievers@vrfy.org>

[jejb: modified for new event API]
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Since the introduction of the acquire_console_sem calls in
0333d835, kexecing can cause the
kernel to deadlock:

 ps3fb_shutdown()
  -> unregister_framebuffer()
  -> fb_notifier_call_chain(FB_EVENT_FB_UNBIND)
  -> fbcon_fb_unbind()
  -> unbind_con_driver()
  -> bind_con_driver()
	[ acquires console_sem ]
  -> fbcon_deinit()
  -> fbops->fb_release(newinfo, 0)
  -> ps3fb_release()
  -> ps3fb_sync()
	[ acquires console_sem ]

This change avoids the deadlock by moving the acquire_console_sem()
out of ps3fb_sync(), and puts it into the two other callsites, leaving
ps3fb_release() to call ps3fb_sync() without the console semaphore.

[Geert]
  - Corrected call sequence above
  - ps3fb_release() may be called with and without console_sem held. This is an
    inconsistency that should be fixed at the fb level, but for now, try to
    acquire console_sem in ps3fb_release().

    I think it's safer to let ps3fb_release() try to acquire console_sem and
    not refresh the screen if it fails, than to call ps3fb_sync() without
    holding console_sem, as ps3fb_par may be modified at the same time, causing
    crashes or lockups.

    Besides, ps3fb_release() only calls ps3fb_sync() to refresh the screen
    when display flipping is disabled, which is an uncommon case (except during
    shutdown/kexec).
Signed-off-by: NJeremy Kerr <jk@ozlabs.org>
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In ps3fb_shutdown, freeing the framebuffer will cause fb_info (in
dev->core.driver_data) to be free()ed, which we potentially access
from the ps3fbd kthread.

This change frees the framebuffer after stopping the ps3fbd kthread.
Signed-off-by: NJeremy Kerr <jk@ozlabs.org>
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The bug causes corruptions of data read from flash.

The original code performs cache invalidation from "adr" to "adr + len"
in do_write_buffer().  Since len and adr could be updated in the code
before invalidation - it causes improper setting of cache invalidation
regions.
Signed-off-by: NMassimo Cirillo <maxcir@gmail.com>
Signed-off-by: NGiuseppe D'Eliseo <giuseppedeliseo@gmail.com>
Acked-by: NNicolas Pitre <nico@cam.org>
Acked-by: NJörn Engel <joern@logfs.org>
Signed-off-by: NDavid Woohouse <dwmw2@infradead.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix oops reported by Trond.
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix driver data name to match whitelist of acceptable names that contain
pointers init data so that section mismatch warning is placated.
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Using an udelay of 5 seems to result in problems for several people.
For now abandon the udelay value of 5 and stick to 10, even though this
will mean a longer load time of the cx2584x firmware.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Don't allocate room for an iovec when it is not needed.
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

Prevent libata from starting/stopping non-ATA devices (like ATAPI floppy
drives) as they don't seem to like it:

sd 1:0:1:0: [sdb] Starting disk
ata2.01: configured for PIO2
sd 1:0:1:0: [sdb] Result: hostbyte=0x00 driverbyte=0x08
sd 1:0:1:0: [sdb] Sense Key : 0x2 [current]
sd 1:0:1:0: [sdb] ASC=0x3a ASCQ=0x0
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Using default methods caused the chip's DMA PRD count registers, inadvertently
starting DMA!  While fixing it, also do:

- get rid of the 'ide_' prefixes in several functions for which the prefix in
  the method's name has been 'ide_' ectomized already;

- align the code hooking the IDE DMA methods in init_hwif_trm290()...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: NGeorge Kibardin <george-kibardin@yandex.ru>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

http://bugzilla.kernel.org/show_bug.cgi?id=9673

ACPI _PS3 cause S4 breaks in the second attempt. The system has a _PS3
method for IDE, which will call into SMM mode. Currently we haven't clue
why just the second attempt fails, as it's totally in BIOS code, so
blacklist the system so far for 2.6.24.

A possible suspect is ACPI NVS isn't save/restore, we will revisit the
bug after linux does ACPI NVS save/restore.

Bart:
- fix scripts/checkpatch.pl complaints
- const-ify ide_acpi_dmi_table[]
Signed-off-by: NShaohua Li <shaohua.li@intel.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Reported-by: NMikko Vinni <mmvinni@yahoo.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Fix commands timeout with Sil3124/3132 based HBA when pass-through ATA
commands [where ATA_QCFLAG_RESULT_TF is set] are used while other
commands are active on other devices connected to the same port with a
Port Multiplier.  Due to a hardware bug, these commands must be sent
alone, like ATAPI commands.
Signed-off-by: NGwendal Grignou <gwendal@google.com>
Acked-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

After non-classifying reset, ehc->classes[] could contain
ATA_DEV_UNKNOWN which used to be normalized to ATA_DEV_NONE for
consistency.  However, this causes unfortunate side effect for drivers
which have non-classifying hardresets (e.g. sata_nv) by making
hardreset report ATA_DEV_NONE for non-classifying resets and thus
makes EH believe that the port is unoccupied and recovery can be
skipped.  The end result is that after a device is swapped with
another one, the new device isn't attached after the old one is
detached.

This patch makes ata_eh_reset() not normalize UNKNOWN to NONE after
non-classifying resets.  This fixes the above problem.  As UNKNOWN and
NONE are handled differently by only EH hotplug logic, this doesn't
cause other behavior changes.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Cc: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Timeout on downstream command may indicate transmission problem on
host link.  Propagate timeouts to host link.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

4726 hates SRST even on non-config ports.  Don't use it.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Fixes a compilation error caused by ata_port_desc() conversion
(cbcdd875).
Signed-off-by: NRod Whitby <rod@whitby.id.au>
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Turns out distros always enabled burst mode and it is pretty essential so
do the same. Also sort out the post DMA mode restore properly.

My 20263 card now seems happy but needs some four drive tests done yet
(when I've persuaded the kernel not to hang in the edd boot code if I
plug them in ..)
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

It is legitimate (although annoying and silly) for a PCI IDE controller
not to be assigned an interrupt and to be polled. The libata-sff code
should therefore not try and request IRQ 0 in this case.
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

During conversion to new EH, sata_qstor was accidentaly changed to use
softreset, which is buggy on this chip, instead of hardreset.  This
patch updates sata_qstor such that it uses hardreset again.

This fixes bugzilla bug 9631.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Cc: Mark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The previous patch fixed spurious read faults from occuring by copying
the data if we happen to have a single block at the end of a page.  It
appears that gcc cannot guarantee 16-byte alignment in the kernel with
__attribute__.  The following report from Torben Viets shows a buffer
that's only 8-byte aligned:

> eneral protection fault: 0000 [#1]
> Modules linked in: xt_TCPMSS xt_tcpmss iptable_mangle ipt_MASQUERADE
> xt_tcpudp xt_mark xt_state iptable_nat nf_nat nf_conntrack_ipv4
> iptable_filter ip_tables x_tables pppoe pppox af_packet ppp_generic slhc
> aes_i586
> CPU:    0
> EIP:    0060:[<c035b828>]    Not tainted VLI
> EFLAGS: 00010292   (2.6.23.12 #7)
> EIP is at aes_crypt_copy+0x28/0x40
> eax: f7639ff0   ebx: f6c24050   ecx: 00000001   edx: f6c24030
> esi: f7e89dc8   edi: f7639ff0   ebp: 00010000   esp: f7e89dc8

Since the hardware must have 16-byte alignment, the following patch fixes
this by open coding the alignment adjustment.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

There's an error remaining in the 32 bit descriptor code after the
conversion to dma accessors:  req_cnt is left uninitialised.

qla1280_32bit_start_scsi gives the following warnings:

drivers/scsi/qla1280.c: In function 'qla1280_32bit_start_scsi':
drivers/scsi/qla1280.c:3044: warning: unused variable 'dma_handle'
drivers/scsi/qla1280.c: In function 'qla1280_queuecommand':
drivers/scsi/qla1280.c:3060: warning: 'req_cnt' is used uninitialized in this function
drivers/scsi/qla1280.c:3042: note: 'req_cnt' was declared here
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

cn_queue_free_callback() will touch 'dev'(i.e. cbq->pdev), so it
should be called before atomic_dec(&dev->refcnt).
Signed-off-by: NLi Zefan <lizf@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For cards that initially have the MAC address stored in reverse order,
the forcedeth driver uses a flag to signal whether the address was
already corrected, so that it is not reversed again on a subsequent
probe.

Unfortunately this flag, which is stored in a register of the card,
seems to get lost during suspend, resulting in the MAC address being
reversed again. To fix that, the MAC address needs to be written back
in reversed order before we suspend and the flag needs to be reset.

The flag is still required because at least kexec will never write
back the reversed address and thus needs to know what state the card
is in.
Signed-off-by: NBjörn Steinbrink <B.Steinbrink@gmx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

usb_control_msg was changed long ago (2.6.12-pre) to take milliseconds
instead of jiffies. Oddly, mcs7830 wasn't added until 2.6.19-rc3.
Signed-off-by: NRuss Dill <Russ.Dill@asu.edu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Back in 2.6.12-pre, usb_start_wait_urb was switched over to take
milliseconds instead of jiffies. kaweth.c was never updated to match.
Signed-off-by: NRuss Dill <Russ.Dill@asu.edu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This makes the ->poll() routines of the E100, E1000, E1000E, IXGB, and
IXGBE drivers complete ->poll() consistently.

Now they will all break out when the amount of RX work done is less
than 'budget'.

At a later time, we may want put back code to include the TX work as
well (as at least one other NAPI driver does, but by in large NAPI
drivers do not do this).  But if so, it should be done consistently
across the board to all of these drivers.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Acked-by: NAuke Kok <auke-jan.h.kok@intel.com>

When we add the generic napi_disable_pending() breakout
logic to net_rx_action() it means that napi_disable()
can cause NAPI poll interrupt events to be disabled.

And this is exactly what we want.  If a napi_disable()
is pending, and we are looping in the ->poll(), we want
->poll() event interrupts to stay disabled and we want
to complete the NAPI poll ASAP.

When ->poll() break out during device down was being handled on a
per-driver basis, often these drivers would turn interrupts back on
when '!netif_running()' was detected.

And this would just cause a reschedule of the NAPI ->poll() in the
interrupt handler before the napi_disable() could get in there and
grab the NAPI_STATE_SCHED bit.

The vast majority of drivers don't care if napi_disable() might have
the side effect of disabling NAPI ->poll() event interrupts.  In all
such cases, when a napi_disable() is performed, the driver just
disabled interrupts or is about to.

However there were three exceptions to this in PCNET32, R8169, and
SKY2.  To fix those cases, at the subsequent napi_enable() points, I
added code to ensure that the ->poll() interrupt events are enabled in
the hardware.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Acked-by: NDon Fry <pcnet32@verizon.net>

If work_done >= budget we should always elide the NAPI
completion.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This will make sure that always the correct core is selected, even if
there are both a PCI and PCI-E core on a PCI or PCI-E card.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Drivers do this to try to break out of the ->poll()'ing loop
when the device is being brought administratively down.

Now that we have a napi_disable() "pending" state we are going
to solve that problem generically.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the parsing of the RX data header channel field.

The current code parses the header incorrectly and passes a wrong
channel number and frequency for each frame to mac80211.
The FIXMEs added by this patch don't matter for now as the code
where they live won't get executed anyway. They will be fixed later.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NChas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This should fix the kernel warn/oops reported while routing.

The tulip driver has a fencepost bug with new NAPI in 2.6.24
It has an off by one bug if a full quantum is reached.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

meth didn't set a valid mac address during probing, but later during
open. Newer kernel refuse to open device with 00:00:00:00:00:00 as mac
address -> dead ethernet. This patch sets the mac address in the probe
function and uses only the mac address from the netdevice struct when
setting up the hardware.
Signed-off-by: NThomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>