Fastsleep is one of the idle state which cpuidle subsystem currently
uses on power8 machines. In this state L2 cache is brought down to a
threshold voltage. Therefore when the core is in fastsleep, the
communication between L2 and L3 needs to be fenced. But there is a bug
in the current power8 chips surrounding this fencing.

OPAL provides a workaround which precludes the possibility of hitting
this bug. But running with this workaround applied causes checkstop
if any correctable error in L2 cache directory is detected. Hence OPAL
also provides a way to undo the workaround.

In the existing implementation, workaround is applied by the last thread
of the core entering fastsleep and undone by the first thread waking up.
But this has a performance cost. These OPAL calls account for roughly
4000 cycles everytime the core has to enter or wakeup from fastsleep.

This patch introduces a sysfs attribute (fastsleep_workaround_applyonce)
to choose the behavior of this workaround.

By default, fastsleep_workaround_applyonce = 0. In this case, workaround
is applied/undone everytime the core enters/exits fastsleep.

fastsleep_workaround_applyonce = 1. In this case the workaround is
applied once on all the cores and never undone. This can be triggered by
echo 1 > /sys/devices/system/cpu/fastsleep_workaround_applyonce

For simplicity this attribute can be modified only once. Implying, once
fastsleep_workaround_applyonce is changed to 1, it cannot be reverted
to the default state.
Signed-off-by: NShreyas B. Prabhu <shreyas@linux.vnet.ibm.com>
Reviewed-by: NPreeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Currently, cpu_online_cores_map returns a mask, which for every core with
at least one online thread, has the bit for thread 0 of the core set to 1,
and the bits for all other threads of the core set to 0. But thread 0 of
the core itself may not be online always. In such cases, if the returned
mask is used for IPI, then it'll cause IPIs to be skipped on cores where
the first thread is offline, because the IPI code refuses to send IPIs to
offline threads.

Fix this by setting the bit of the first online thread in the core.
This is done by fixing this in the underlying function
cpu_thread_mask_to_cores.

The result has the property that for all cores with online threads, there
is one bit set in the returned map. And further, all bits that are set in
the returned map correspond to online threads.
Signed-off-by: NShreyas B. Prabhu <shreyas@linux.vnet.ibm.com>
Reviewed-by: NPreeti U Murthy <preeti@linux.vnet.ibm.com>
[ Changelog from Michael Ellerman <mpe@ellerman.id.au> ]
Reviewed-by: NGautham R. Shenoy <ego@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The commit 8170a83f ("powerpc: Wireup the kcmp syscall to sys_ni") has
disabled the kcmp syscall for powerpc.  This has been done due to the use
of unsigned long parameters which may require a dedicated wrapper to handle
32bit process on top of 64bit kernel.  However in the kcmp() case, the 2
unsigned long parameters are currently only used to carry file descriptors
from user space to the kernel.  Since such a parameter is passed through
register, and file descriptor doesn't need to get extended, there is,
today, no need for a wrapper.

In the case there will be a need to pass address in or out of this system
call, then a wrapper could be required, it will then be to care of it.

As today this is not the case, it is safe to enable kcmp() on powerpc.

Tested (by Laurent) on 64-bit, 32-bit, and 32-bit userspace on 64-bit
kernel using tools/testing/selftests/kcmp [mpe].
Signed-off-by: NLaurent Dufour <ldufour@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The patch defines PCI error types and functions in uapi/asm/eeh.h
and exports function eeh_pe_inject_err(), which will be called by
VFIO driver to inject the specified PCI error to the indicated
PE for testing purpose.
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

There are two equivalent sets of PE state constants, defined in
arch/powerpc/include/asm/eeh.h and include/uapi/linux/vfio.h.
Though the names are different, their corresponding values are
exactly same. The former is used by EEH core and the latter is
used by userspace.

The patch moves those constants from arch/powerpc/include/asm/eeh.h
to arch/powerpc/include/uapi/asm/eeh.h, which are expected to be
used by userspace from now on. We can't delete those constants in
vfio.h as it's uncertain that those constants have been or will be
used by userspace.
Suggested-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NGavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The STRICT_MM_TYPECHECKS code has bit-rotted over the years. To make it
possible to easily build test it, make it a CONFIG option.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This reverts commit feba4036.

Although the principle of this change is good, the implementation has a
few issues.

Firstly we can sometimes fail to abort a syscall because r12 may have
been clobbered by C code if we went down the virtual CPU accounting
path, or if syscall tracing was enabled.

Secondly we have decided that it is safer to abort the syscall even
earlier in the syscall entry path, so that we avoid the syscall tracing
path when we are transactional.

So that we have time to thoroughly test those changes we have decided to
revert this for this merge window and will merge the fixed version in
the next window.

NB. Rather than reverting the selftest we just drop tm-syscall from
TEST_PROGS so that it's not run by default.

Fixes: feba4036 ("powerpc/tm: Abort syscalls in active transactions")
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This replaces the assembler code for kvmhv_commence_exit() with C code
in book3s_hv_builtin.c.  It also moves the IPI sending code that was
in book3s_hv_rm_xics.c into a new kvmhv_rm_send_ipi() function so it
can be used by kvmhv_commence_exit() as well as icp_rm_set_vcpu_irq().
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NAlexander Graf <agraf@suse.de>

Currently, the entry_exit_count field in the kvmppc_vcore struct
contains two 8-bit counts, one of the threads that have started entering
the guest, and one of the threads that have started exiting the guest.
This changes it to an entry_exit_map field which contains two bitmaps
of 8 bits each.  The advantage of doing this is that it gives us a
bitmap of which threads need to be signalled when exiting the guest.
That means that we no longer need to use the trick of setting the
HDEC to 0 to pull the other threads out of the guest, which led in
some cases to a spurious HDEC interrupt on the next guest entry.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NAlexander Graf <agraf@suse.de>

We can tell when a secondary thread has finished running a guest by
the fact that it clears its kvm_hstate.kvm_vcpu pointer, so there
is no real need for the nap_count field in the kvmppc_vcore struct.
This changes kvmppc_wait_for_nap to poll the kvm_hstate.kvm_vcpu
pointers of the secondary threads rather than polling vc->nap_count.
Besides reducing the size of the kvmppc_vcore struct by 8 bytes,
this also means that we can tell which secondary threads have got
stuck and thus print a more informative error message.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NAlexander Graf <agraf@suse.de>

Rather than calling cond_resched() in kvmppc_run_core() before doing
the post-processing for the vcpus that we have just run (that is,
calling kvmppc_handle_exit_hv(), kvmppc_set_timer(), etc.), we now do
that post-processing before calling cond_resched(), and that post-
processing is moved out into its own function, post_guest_process().

The reschedule point is now in kvmppc_run_vcpu() and we define a new
vcore state, VCORE_PREEMPT, to indicate that that the vcore's runner
task is runnable but not running.  (Doing the reschedule with the
vcore in VCORE_INACTIVE state would be bad because there are potentially
other vcpus waiting for the runner in kvmppc_wait_for_exec() which
then wouldn't get woken up.)

Also, we make use of the handy cond_resched_lock() function, which
unlocks and relocks vc->lock for us around the reschedule.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NAlexander Graf <agraf@suse.de>

* Remove unused kvmppc_vcore::n_busy field.
* Remove setting of RMOR, since it was only used on PPC970 and the
  PPC970 KVM support has been removed.
* Don't use r1 or r2 in setting the runlatch since they are
  conventionally reserved for other things; use r0 instead.
* Streamline the code a little and remove the ext_interrupt_to_host
  label.
* Add some comments about register usage.
* hcall_try_real_mode doesn't need to be global, and can't be
  called from C code anyway.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NAlexander Graf <agraf@suse.de>

Previously, if kvmppc_run_core() was running a VCPU that needed a VPA
update (i.e. one of its 3 virtual processor areas needed to be pinned
in memory so the host real mode code can update it on guest entry and
exit), we would drop the vcore lock and do the update there and then.
Future changes will make it inconvenient to drop the lock, so instead
we now remove it from the list of runnable VCPUs and wake up its
VCPU task.  This will have the effect that the VCPU task will exit
kvmppc_run_vcpu(), go around the do loop in kvmppc_vcpu_run_hv(), and
re-enter kvmppc_run_vcpu(), whereupon it will do the necessary call
to kvmppc_update_vpas() and then rejoin the vcore.

The one complication is that the runner VCPU (whose VCPU task is the
current task) might be one of the ones that gets removed from the
runnable list.  In that case we just return from kvmppc_run_core()
and let the code in kvmppc_run_vcpu() wake up another VCPU task to be
the runner if necessary.

This all means that the VCORE_STARTING state is no longer used, so we
remove it.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NAlexander Graf <agraf@suse.de>

This reads the timebase at various points in the real-mode guest
entry/exit code and uses that to accumulate total, minimum and
maximum time spent in those parts of the code.  Currently these
times are accumulated per vcpu in 5 parts of the code:

* rm_entry - time taken from the start of kvmppc_hv_entry() until
  just before entering the guest.
* rm_intr - time from when we take a hypervisor interrupt in the
  guest until we either re-enter the guest or decide to exit to the
  host.  This includes time spent handling hcalls in real mode.
* rm_exit - time from when we decide to exit the guest until the
  return from kvmppc_hv_entry().
* guest - time spend in the guest
* cede - time spent napping in real mode due to an H_CEDE hcall
  while other threads in the same vcore are active.

These times are exposed in debugfs in a directory per vcpu that
contains a file called "timings".  This file contains one line for
each of the 5 timings above, with the name followed by a colon and
4 numbers, which are the count (number of times the code has been
executed), the total time, the minimum time, and the maximum time,
all in nanoseconds.

The overhead of the extra code amounts to about 30ns for an hcall that
is handled in real mode (e.g. H_SET_DABR), which is about 25%.  Since
production environments may not wish to incur this overhead, the new
code is conditional on a new config symbol,
CONFIG_KVM_BOOK3S_HV_EXIT_TIMING.
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NAlexander Graf <agraf@suse.de>

This creates a debugfs directory for each HV guest (assuming debugfs
is enabled in the kernel config), and within that directory, a file
by which the contents of the guest's HPT (hashed page table) can be
read.  The directory is named vmnnnn, where nnnn is the PID of the
process that created the guest.  The file is named "htab".  This is
intended to help in debugging problems in the host's management
of guest memory.

The contents of the file consist of a series of lines like this:

  3f48 4000d032bf003505 0000000bd7ff1196 00000003b5c71196

The first field is the index of the entry in the HPT, the second and
third are the HPT entry, so the third entry contains the real page
number that is mapped by the entry if the entry's valid bit is set.
The fourth field is the guest's view of the second doubleword of the
entry, so it contains the guest physical address.  (The format of the
second through fourth fields are described in the Power ISA and also
in arch/powerpc/include/asm/mmu-hash64.h.)
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NAlexander Graf <agraf@suse.de>

This adds helper routines for locking and unlocking HPTEs, and uses
them in the rest of the code.  We don't change any locking rules in
this patch.
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NAlexander Graf <agraf@suse.de>

We don't support real-mode areas now that 970 support is removed.
Remove the remaining details of rma from the code.  Also rename
rma_setup_done to hpte_setup_done to better reflect the changes.
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NAlexander Graf <agraf@suse.de>

Some PowerNV systems include a hardware random-number generator.
This HWRNG is present on POWER7+ and POWER8 chips and is capable of
generating one 64-bit random number every microsecond.  The random
numbers are produced by sampling a set of 64 unstable high-frequency
oscillators and are almost completely entropic.

PAPR defines an H_RANDOM hypercall which guests can use to obtain one
64-bit random sample from the HWRNG.  This adds a real-mode
implementation of the H_RANDOM hypercall.  This hypercall was
implemented in real mode because the latency of reading the HWRNG is
generally small compared to the latency of a guest exit and entry for
all the threads in the same virtual core.

Userspace can detect the presence of the HWRNG and the H_RANDOM
implementation by querying the KVM_CAP_PPC_HWRNG capability.  The
H_RANDOM hypercall implementation will only be invoked when the guest
does an H_RANDOM hypercall if userspace first enables the in-kernel
H_RANDOM implementation using the KVM_CAP_PPC_ENABLE_HCALL capability.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NAlexander Graf <agraf@suse.de>

On POWER, storage caching is usually configured via the MMU - attributes
such as cache-inhibited are stored in the TLB and the hashed page table.

This makes correctly performing cache inhibited IO accesses awkward when
the MMU is turned off (real mode).  Some CPU models provide special
registers to control the cache attributes of real mode load and stores but
this is not at all consistent.  This is a problem in particular for SLOF,
the firmware used on KVM guests, which runs entirely in real mode, but
which needs to do IO to load the kernel.

To simplify this qemu implements two special hypercalls, H_LOGICAL_CI_LOAD
and H_LOGICAL_CI_STORE which simulate a cache-inhibited load or store to
a logical address (aka guest physical address).  SLOF uses these for IO.

However, because these are implemented within qemu, not the host kernel,
these bypass any IO devices emulated within KVM itself.  The simplest way
to see this problem is to attempt to boot a KVM guest from a virtio-blk
device with iothread / dataplane enabled.  The iothread code relies on an
in kernel implementation of the virtio queue notification, which is not
triggered by the IO hcalls, and so the guest will stall in SLOF unable to
load the guest OS.

This patch addresses this by providing in-kernel implementations of the
2 hypercalls, which correctly scan the KVM IO bus.  Any access to an
address not handled by the KVM IO bus will cause a VM exit, hitting the
qemu implementation as before.

Note that a userspace change is also required, in order to enable these
new hcall implementations with KVM_CAP_PPC_ENABLE_HCALL.
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
[agraf: fix compilation]
Signed-off-by: NAlexander Graf <agraf@suse.de>

Switch to using the newly created asm-generic/seccomp.h for the seccomp
strict mode syscall definitions.  The obsolete sigreturn in COMPAT mode is
retained as an override.  Remaining definitions are identical, though they
incorrectly appeared in uapi, which has been corrected.
Signed-off-by: NKees Cook <keescook@chromium.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

For THP that is marked trans splitting, we return the pte.
This require the callers to handle the pmd_trans_splitting scenario,
if they care. All the current callers are either looking at pfn or
write_ok, hence we don't need to update them.
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

We can disable a THP split or a hugepage collapse by disabling irq.
We do send IPI to all the cpus in the early part of split/collapse,
and disabling local irq ensure we don't make progress with
split/collapse. If the THP is getting split we return NULL from
find_linux_pte_or_hugepte(). For all the current callers it should be ok.
We need to be careful if we want to use returned pte_t pointer outside
the irq disabled region. W.r.t to THP split, the pfn remains the same,
but then a hugepage collapse will result in a pfn change. There are
few steps we can take to avoid a hugepage collapse.One way is to take page
reference inside the irq disable region. Other option is to take
mmap_sem so that a parallel collapse will not happen. We can also
disable collapse by taking pmd_lock. Another method used by kvm
subsystem is to check whether we had a mmu_notifer update in between
using mmu_notifier_retry().
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This patch remove helpers which we had used only once in the code.
Limiting page table walk variants help in ensuring that we won't
end up with code walking page table with wrong assumptions.
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

pte can get updated from other CPUs as part of multiple activities
like THP split, huge page collapse, unmap. We need to make sure we
don't reload the pte value again and again for different checks.
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The arch_randomize_brk() function is used on several architectures,
even those that don't support ET_DYN ASLR. To avoid bulky extern/#define
tricks, consolidate the support under CONFIG_ARCH_HAS_ELF_RANDOMIZE for
the architectures that support it, while still handling CONFIG_COMPAT_BRK.
Signed-off-by: NKees Cook <keescook@chromium.org>
Cc: Hector Marco-Gisbert <hecmargi@upv.es>
Cc: Russell King <linux@arm.linux.org.uk>
Reviewed-by: NIngo Molnar <mingo@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: "David A. Long" <dave.long@linaro.org>
Cc: Andrey Ryabinin <a.ryabinin@samsung.com>
Cc: Arun Chandran <achandran@mvista.com>
Cc: Yann Droneaud <ydroneaud@opteya.com>
Cc: Min-Hua Chen <orca.chen@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Alex Smith <alex@alex-smith.me.uk>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Vineeth Vijayan <vvijayan@mvista.com>
Cc: Jeff Bailey <jeffbailey@google.com>
Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Behan Webster <behanw@converseincode.com>
Cc: Ismael Ripoll <iripoll@upv.es>
Cc: Jan-Simon Mller <dl9pf@gmx.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NRichard Weinberger <richard@nod.at>

The hard lockup detector uses a PMU event as a periodic NMI to
detect if we are stuck (where stuck means no timer interrupts have
occurred).

Ben's rework of the ppc64 soft disable code has made ppc64 PMU
exceptions a partial NMI. They can get disabled if an external
interrupt comes in, but otherwise PMU interrupts will fire in
interrupt disabled regions.

We disable the hard lockup detector by default for a few reasons:

- It breaks userspace event based branches on POWER8.
- It is likely to produce false positives on KVM guests.
- Since PMCs can only count to 2^31, counting cycles means we might
  take multiple PMU exceptions per second per hardware thread even
  if our hard lockup timeout is 10 seconds.

It can be enabled via a boot option, or via procfs.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This change adds the OPAL interface definitions to allow Linux to read,
write and erase from system flash devices. We register platform devices
for the flash devices exported by firmware.

We clash with the existing opal_flash_init function, which is really for
the FSP flash update functionality, so we rename that initcall to
opal_flash_update_init().

A future change will add an mtd driver that uses this interface.

Changes from Joel Stanley and Jeremy Kerr.
Signed-off-by: NCyril Bur <cyrilbur@gmail.com>
Signed-off-by: NJeremy Kerr <jk@ozlabs.org>
Signed-off-by: NJoel Stanley <joel@jms.id.au>
Acked-by: NStewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This patch changes the syscall handler to doom (tabort) active
transactions when a syscall is made and return immediately without
performing the syscall.

Currently, the system call instruction automatically suspends an
active transaction which causes side effects to persist when an active
transaction fails.

This does change the kernel's behaviour, but in a way that was
documented as unsupported. It doesn't reduce functionality because
syscalls will still be performed after tsuspend. It also provides a
consistent interface and makes the behaviour of user code
substantially the same across powerpc and platforms that do not
support suspended transactions (e.g. x86 and s390).

Performance measurements using
http://ozlabs.org/~anton/junkcode/null_syscall.c
indicate the cost of a system call increases by about 0.5%.
Signed-off-by: NSam Bobroff <sam.bobroff@au1.ibm.com>
Acked-By: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Remove shims, patch callsites to use pci_controller_ops
versions instead.

Also move back the probe mode defines, as explained in the patch
for pci_probe_mode.
Signed-off-by: NDaniel Axtens <dja@axtens.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

If a pci_controller_ops struct is provided to iommu_init_early_dart,
populate that with the DMA setup ops, rather than ppc_md. If NULL is
provided, populate ppc_md as before.

This also patches the call sites for Maple and Power Mac to pass
NULL, so existing behaviour is preserved.

The benefit of making this optional is that it means we don't have
to change dart, Maple and Power Mac over to the controller_ops
system in one fell swoop.
Signed-off-by: NDaniel Axtens <dja@axtens.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Add pci_controller_ops.reset_secondary_bus,
shadowing ppc_md.pcibios_reset_secondary_bus.
Add a shim, and changes the callsites to use the shim.

Use pcibios_reset_secondary_bus_shim, as both
pcibios_reset_secondary_bus and pci_reset_secondary_bus
are already taken.
Signed-off-by: NDaniel Axtens <dja@axtens.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Add pci_controller_ops.window_alignment,
shadowing ppc_md.pcibios_window_alignment.
Add a shim, and changes the callsites to use the shim.

Here, we use pci_window_alignment, as pcibios_window_alignment is
already taken.
Signed-off-by: NDaniel Axtens <dja@axtens.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Add pci_controller_ops.enable_device_hook,
shadowing ppc_md.pcibios_enable_device_hook.
Add a shim, and changes the callsites to use the shim.
Signed-off-by: NDaniel Axtens <dja@axtens.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Add pci_controller_ops.probe_mode, shadowing ppc_md.pci_probe_mode.
Add a shim, and changes the callsites to use the shim.

We also need to move the probe mode defines to pci-bridge.h from pci.h.
They are required by the shim in order to return a sensible default.
Previously, the were defined in pci.h, but pci.h includes pci-bridge.h
before the relevant #defines. This means the definitions are absent
if pci.h is included before pci-bridge.h. This occurs in some drivers.
So, move the definitons now, and move them back when we remove the shim.

Anything that wants the defines would have had to include pci.h, and
since pci.h includes pci-bridge.h, nothing will lose access to the
defines.
Signed-off-by: NDaniel Axtens <dja@axtens.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Add pci_controller_ops.dma_bus_setup, shadowing ppc_md.pci_dma_bus_setup.
Add a shim, and changes the callsites to use the shim.
Signed-off-by: NDaniel Axtens <dja@axtens.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Introduces the pci_controller_ops structure.
Add pci_controller_ops.dma_dev_setup, shadowing ppc_md.pci_dma_dev_setup.
Add a shim, and change the callsites to use the shim.
Signed-off-by: NDaniel Axtens <dja@axtens.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

pcibios_enable_device_hook returned an int. Every implementation
returned either -EINVAL or 0. The return value wasn't propagated by
the caller: any non-zero return value caused pcibios_enable_device
to return -EINVAL itself. Therefore, make the hook return a bool.
Signed-off-by: NDaniel Axtens <dja@axtens.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Previously, find_and_init_phbs() was used in both PowerNV and pSeries
setup. However, since RTAS support has been dropped from PowerNV, we
can move it into a platform-specific file.
Signed-off-by: NDaniel Axtens <dja@axtens.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

smp_ops->probe() is currently supposed to return the number of cpus in
the system.

The last actual usage of the value was removed in May 2007 in e147ec8f
"[POWERPC] Simplify smp_space_timers". We still passed the value around
until June 2010 when even that was finally removed in c1aa687d
"powerpc: Clean up obsolete code relating to decrementer and timebase".

So drop that requirement, probe() now returns void, and update all
implementations.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>