Enhance debugging messages for the hotkey subdriver.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

Enhance debugging messages for all rfkill subdrivers in thinkpad-acpi.

Also, log a warning if the deprecated sysfs attributes are in use.
These attributes are going to be removed sometime in 2010.

There is an user-visible side-effect: we now coalesce attempts to
enable/disable bluetooth or WWAN in the procfs interface, instead of
hammering the firmware with multiple requests.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

Some of the ThinkPad LEDs indicate critical conditions that can cause
data loss or cause hardware damage when ignored (e.g. force-ejecting
a powered up bay; ignoring a failing battery, or empty battery; force-
undocking with the dock buses still active, etc).

On almost all ThinkPads, LED access is write-only, and the firmware
usually does fire-and-forget signaling on them, so you effectively
lose whatever message the firmware was trying to convey to the user
when you override the LED state, without any chance to restore it.

Restrict access to all LEDs that can convey important alarms, or that
could mislead the user into incorrectly operating the hardware.  This
will make the Lenovo engineers less unhappy about the whole issue.

Allow users that really want it to still control all LEDs, it is the
unaware user that we have to worry about.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

The HKEY disable functionality basically cripples the entire event
model of the ThinkPad firmware and of the thinkpad-acpi driver.
Remove this functionality from the driver.  HKEY must be enabled at
all times while thinkpad-acpi is loaded, and disabled otherwise.

For sysfs, according to the sysfs ABI and the thinkpad-acpi sysfs
rules of engagement, we will just remove the attributes.  This will be
done in two stages: disable their function now, after two kernel
releases, remove the attributes.

For procfs, we call WARN().  If nothing triggers it, I will simply
remove the enable/disable commands entirely in the future along with
the sysfs attributes.

I don't expect much, if any fallout from this.  There really isn't any
reason to mess with hotkey_enable or with the enable/disable commands
to /proc/acpi/ibm/hotkey, and this has been true for years...
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

Add a debug helper that discloses the TGID of the userspace task
attempting to access the driver.  This is highly useful when dealing
with bug reports, since often the user has no idea that some userspace
application is accessing thinkpad-acpi...

Also add a helper to log warnings about sysfs attributes that are
deprecated.

Use the new helpers to issue deprecation warnings for bluetooth_enable
and wwan_enabled, that have been deprecated for a while, now.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

Some cleanups to the documentation of the driver.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

It is about time to bump up the version.

Features added since 0.21:  fan suspend/resume support, preserve radio
state across power off (for some radio types), built-in UWB radio
rfkill support and thermal alarm events support.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

Add rfkill support for USB UWB radio devices on very recent ThinkPad
laptop models.

The new subdriver is moslty a trimmed down copy of the wwan subdriver.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Update documentation to reflect the new location of the
thinkpad-acpi driver.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

It is always "an" if there is a vowel _spoken_ (not written).
So it is:
"an hour" (spoken vowel)
but
"a uniform" (spoken 'j')
Signed-off-by: NFrederik Schwarzer <schwarzerf@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

The WWAN radio control has been working well for over three years,
and is no longer experimental.
Signed-off-by: NJeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: NAndi Kleen <ak@linux.intel.com>

rfkill support deserves a new version checkpoint...
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>

Add a read/write rfkill interface to the bluetooth radio switch on the
bluetooth submodule, and one for the wireless wan radio switch to the wan
submodule.

Since rfkill does care for when a switch changes state, use WLSW
notifications to also check if the WWAN or Bluetooth switches did not
change state (due to them being slaves of WLSW in firmware/hardware, but
that reality not being always properly exported by the thinkpad firmware).
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: John W. Linville <linville@tuxdriver.com>

Rename SW_RADIO to SW_RFKILL_ALL in thinkpad-acpi code and docs, following
5adad013 "Input: rename SW_RADIO to
SW_RFKILL_ALL".
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

Full LED sysfs support, and the rest of the assorted minor fixes and
enhancements are a good reason to checkpoint a new version...
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

Change all occourences of the "led" word to full uppercase in user
documentation.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Acked-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Add a sysfs led class interface to the led subdriver.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: NLen Brown <len.brown@intel.com>

Add a sysfs led class interface to the thinklight (light subdriver).
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: NLen Brown <len.brown@intel.com>

Unfortunately, a lot of stuff in the kernel has size limitations, so
"thinkpad-acpi" ends up eating up too much real estate.  We were using
"tpacpi" in symbols already, but this shorthand was not visible to
userland.

Document that the driver will use tpacpi as a short hand where necessary,
and use it to name the kernel thread for NVRAM polling (now named
"ktpacpi_nvramd").

Also, register a module alias with the shorthand.  One can refer to the
module using the shorthand name.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

Lenovo ThinkPads with generic ACPI backlight level control can be easily
set to react to keyboard brightness key presses in a more predictable way
than what they do when in "DOS / bootloader" mode after Linux brings
up the ACPI interface.

The switch to the ACPI backlight mode in the firmware is designed to be
safe to use only as an one way trapdoor.  One is not to force the firmware
to switch back to "DOS/bootloader" mode except by rebooting.  The mode
switch itself is performed by calling any of the ACPI _BCL methods at least
once.

When in ACPI mode, the backlight firmware just issues (standard) events for
the brightness up/down hot key presses along with the non-standard HKEY
events which thinkpad-acpi traps, and doesn't touch the hardware.

thinkpad-acpi will:

1. Place the ThinkPad firmware in ACPI backlight control mode
   if one is available
2. Suppress HKEY backlight change notifications by default
   to avoid double-reporting when ACPI video is loaded when
   the ThinkPad is in ACPI backlight control mode
3. Urge the user to load the ACPI video driver

The user is free to use either the ACPI video driver to get the brightness
key events, or to override the thinkpad-acpi default hotkey mask to get
them from thinkpad-acpi as well (this will result in duplicate events if
ACPI video is loaded, so let's hope distros won't screw this up).

Provided userspace is sane, all should work (and *keep* working), which is
more that can be said about the non-ACPI mode of the new Lenovo ThinkPad
BIOSes when coupled to current userspace and X.org drivers.

Full guidelines for backlight hot key reporting and use of the
thinkpad-acpi backlight interface have been added to the documentation.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Thomas Renninger <trenn@suse.de>
Signed-off-by: NLen Brown <len.brown@intel.com>

A quick study of the 0x5009/0x500A HKEY event on the X61t DSDT revealed the
existence of the EC HTAB register (EC 0x0f, bit 7), and a compare with the
X41t DSDT shows that HKEY.MHKG can be used to verify if the ThinkPad is
tablet-capable (MHKG present), and in tablet mode (bit 3 of MHKG return is
set).

Add an attribute to report this information, "hotkey_tablet_mode".  This
attribute has poll()/select() support, and can be used along with EV_SW
SW_TABLET_MODE to hook userspace to tablet events.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

Fixes some minor points in the radio switch code and docs.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

Fix a few spelling errors, and also document the EV_SW events thinkpad-acpi
can issue.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

Issue EV_SW SW_TABLET_MODE events for HKEY events 0x5009 and 0x500A on the
X41t/X60t/X61t.  As usual, we suppress the HKEY events on the netlink
interface to avoid sending duplicate events to userspace.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

Fix a stray ibm-acpi that should have been replaced with thinkpad-acpi.
Thanks to Damjan <gdamjan@mail.net.mk> for noticing this one.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

Also update references to thinkpad-acpi.txt in Kconfig.
Signed-off-by: NCarlos Corbacho <carlos@strangeworlds.co.uk>
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
CC: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

The major code reorganization and cleanups, and new HKEY events, plus
poll()/select() support are good reasons to checkpoint a new version...
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

Implement poll()/select() support through sysfs_notify() for some key
attributes which userspace might want to poll() or select() on.

In order to let userspace know poll()/select() support is available for an
attribute, the thinkpad-acpi sysfs interface version is also bumped up.
Further changes that add poll()/select() capabilities to any pre-existing
attributes will also increment the sysfs interface version.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

Tomas Carnecky reports that events 0x5009 and 0x500a are swivel events, and
that 0x500b/0x500c are tablet pen storage bay events.

Document these events, and avoid nasty messages when they happen.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

Handle some HKEY events that the firmware uses to report the reason for a
wake up, and to also notify that the system could go back to sleep (if it
woke up just to eject something from the bay, or to undock).

The driver will report the reason of the last wake up in the sysfs
attribute "wakeup_reason": 0 for "none, unknown, or standard ACPI wake up
event", 1 for "bay ejection request" and 2 for "undock request".

The firmware will also report if the operation that triggered the wake up
has been completed, by issuing an HKEY 0x3003 or 0x4003 event.  If the
operation fails, no event is sent.  When such a hotunplug sucessfull
notification is issued, the driver sets the attribute
"wakeup_hotunplug_complete" to 1.

While the firmware does tell us whether we are waking from a suspend or
hibernation scenario, the Linux way of hibernating makes this information
not reliable, and therefore it is not reported.

The idea is that if any of these attributes are non-zero, userspace might
want to do something at the end of the "wake up from sleep" procedures,
such as offering to send the machine back into sleep as soon as it is safe
to do so.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

Use a generic message on hotkey_notify to log unknown and unhandled events,
and cleanup hotkey_notify a little.

Also, document event 0x5010 (brightness changed notification) and do not
log it as an unknown event (even if we do not use it for anything right
now).
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

The NVRAM polling support for hot keys is reason enough to
bump up the version string.  Do it.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

Older ThinkPad models do not export some of the hot keys over the
event-based ACPI hot key interface.  For these models, one has to poll
the CMOS NVRAM to check the key state at a rate faster than the expected
rate at which the user might repeatedly press the same hot key.

This patch implements this functionality for many of the hotkeys in a
transparent way: hot keys will now Just Work, and the driver knows the
best approach (events or NVRAM polling) to employ, based on the
HKEY.MHKA ACPI method.

Also, the driver can turn off the polling when there are no users for
the hot keys that need such polling.

The NVRAM-based hot keys of the A3x series that have never been
implemented by later models are not supported, to avoid changes in the
keymap of the input devices that could cause headaches in the future.

There is a Kconfig option to avoid compiling the NVRAM polling code, as
it is not very small, and unlikely to be useful on any ThinkPad newer
than a T40, X31 or R52.

This feature is based on a previous effort by Richard Hughes.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Richard Hughes <hughsient@gmail.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

The lm-sensors 3.0.0/libsensors4 compatibility changes are reason enough to
bump up the version string.  Do it.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

Newer Lenovo BIOSes support the standard ACPI backlight brightness
interface (_BCM, _BQC, _BCL).  It should be used instead of the native
thinkpad backlight brightness control interface when possible.

This patch disables the native brightness support in the driver by default
when we detect that the standard ACPI interface is available.  The local
admin can still enable it using the module parameter "brightness_enable".

Note that we need to detect the standard ACPI backlight interface only in
boxes for which we would load the native backlight interface in the first
place, and that no ThinkPad BIOS has _BCL but misses the other methods, so
the detection routines can be really simple.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

Add a "brightness_enable" module parameter that allows the local admin to
force the backlight support to not be enabled.

It can also be used to force the backlight support to be enabled, but that
is currently a no-op as the backlight support is enabled by default when
available.  This will be changed by a different patch.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

Lenovo ThinkPads often have 16 brightness levels in EC, and not just eight
levels like older ThinkPads.  They also have standard ACPI backlight
brightness control.

We detect the number of brightness levels by the presence of a BCLL package
with 16 entries.  If BCLL is not there, we assume eight levels (Z6*).  If
it is there, but it doesn't have 16 entries, we assume eight levels (T60).
Otherwise we assume sixteen levels (T61, X61, etc).

We don't use _BCL because it can have side-effects in thinkpads.  Thanks to
Thomas Renninger <trenn@suse.de> for notifying me of this potential
problem.

Using the standard ACPI backlight brightness control *instead* of the
native thinkpad backlight control is a better idea, though.  A different
patch will take care of this.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Thomas Renninger <trenn@suse.de>
Signed-off-by: NLen Brown <len.brown@intel.com>

Most of these fixes were already submitted for old kernel versions, and were
approved, but for some reason they never made it into the releases.

Because this is a consolidation of a couple old missed patches, it touches both
Kconfigs and documentation texts.
Signed-off-by: NMatt LaPlante <kernel1@cyberdogtech.com>
Acked-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NAdrian Bunk <bunk@kernel.org>

Spelling fixes in Documentation/.
Signed-off-by: NSimon Arlott <simon@fire.lp0.eu>
Signed-off-by: NAdrian Bunk <bunk@kernel.org>

Use a separate platform device and driver ("thinkpad_hwmon") to attach
hwmon attributes and class, and add a name attribute of "thinkpad" to
it, which defines the hwmon device name for libsensors4.

This makes thinkpad-acpi compatible with libsensors4 from lm-sensors, and
the platform driver and device split will make it much easier to separate
hwmon functionality into its own module later on.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: NLen Brown <len.brown@intel.com>