Skip to content

cloud-kernel
cloud-kernel

openanolis / cloud-kernel
1 年多 前同步成功

通知 160
Star 36
Fork 7
cloud-kernel
cloud-kernel
切换分支/标签
  1. 01 8月, 2017 22 次提交
  3. 31 7月, 2017 12 次提交
    • D
      Merge branch 'net-sched-actions-improve-dump-performance' · 764646b0
      由 David S. Miller 提交于 
      Jamal Hadi Salim says:

====================
net sched actions: improve dump performance

Changes since v11:
------------------
1) Jiri - renames: nla_value to value and nla_selector to selector
2) Jiri - rename: validate_nla_bitfield_32 to validate_nla_bitfield_32
3) Jiri - rename: NLA_BITFIELD_32 to NLA_BITFIELD32
4) Jiri - remove unnecessary break when we return in case statement
5) Jiri - rename and move nla_get_bitfield_32 to an earlier patch
6) Jiri - xmas tree alignment of var declaration
7) Jiri - rename all declarations of bitfield 32 vars to be consistent ("bf")
8) Jiri - improve validate_nla_bitfield32() validation to disallow valid
          bit values that are not selected by the selector

Changes since v10:
-----------------
1) Jiri: move type->validate_content() to its own patch
Jamal: decided to remove it altogether so we can get this patch set in.

2) Change name of NLA_FLAG_BITS to NLA_BITFIELD_32 based on discussions
with D. Ahern and Jiri. D. Ahern suggests to make this a variable bitmap size.
My analysis at this point is it too complex and i only need a few bit
flags. If we run out of bits someone else can create a new NLA_BITFIELD_XXX
and start using that. So please let this go.

3) Jamal - Add Suggested-by: Jiri for type NLA_BITFIELD_32

4) Jiri: Change name allowed_flags to tcaa_root_flags_allowed

5) Jiri: Introduce nla_get_flag_bits_values() helper instead of using
memcpy for retrieving nla_bitfield_32 fields.

Changes since v9:
-----------------

1) General consensus:
- remove again the use of BIT() to maintain uapi consistency ;->

1) Jiri:
- Add a new netlink type NLA_FLAG_BITS to check for valid bits
  and use it instead of inline vetting (patch 4/4 now)

Changes since v8:
-----------------

1) Jiri:
- Add back the use of BIT(). Eventually fix iproute2 instead
- Rename VALID_TCA_FLAGS to VALID_TCA_ROOT_FLAGS

Changes since v7:
-----------------

Jamal:
No changes.
Patch 1 went out twice. Resend without two copies of patch 1

changes since v6:
-----------------

1) DaveM:
New rules for netlink messages. From now on we are going to start
checking for bits that are not used and rejecting anything we dont
understand. In the future this is going to require major changes
to user space code (tc etc). This is just a start.

To quote, David:
"
 Again, bits you aren't using now, make sure userspace doesn't
   set them.  And if it does, reject.
"
Added checks for ensuring things work as above.

2) Jiri:
a)Fix the commit message to properly use "Fixes" description
b)Align assignments for nla_policy

Changes since v5:
----------------

0)
Remove use of BIT() because it is kernel specific. Requires a separate
patch (Jiri can submit that in his cleanups)

1)To paraphrase Eric D.

"memcpy(nla_data(count_attr), &cb->args[1], sizeof(u32));
wont work on 64bit BE machines because cb->args[1]
(which is 64 bit is larger in size than sizeof(u32))"

Fixed

2) Jiri Pirko

i) Spotted a bug fix mixed in the patch for wrong TLV
fix. Add patch 1/3 to address this. Make part of this
series because of dependencies.

ii) Rename ACT_LARGE_DUMP_ON -> TCA_FLAG_LARGE_DUMP_ON

iii) Satisfy Jiri's obsession against the noun "tcaa"
a)Rename struct nlattr *tcaa --> struct nlattr *tb
b)Rename TCAA_ACT_XXX -> TCA_ROOT_XXX

Changes since v4:
-----------------

1) Eric D.

pointed out that when all skb space is used up by the dump
there will be no space to insert the TCAA_ACT_COUNT attribute.

2) Jiri:

i) Change:

enum {
        TCAA_UNSPEC,
        TCAA_ACT_TAB,
        TCAA_ACT_FLAGS,
        TCAA_ACT_COUNT,
        TCAA_ACT_TIME_FILTER,
        __TCAA_MAX
};

to:
enum {
       TCAA_UNSPEC,
       TCAA_ACT_TAB,
       TCAA_ACT_FLAGS,
       TCAA_ACT_COUNT,
       __TCAA_MAX,
};

Jiri plans to followup with the rest of the code to make the
style consistent.

ii) Rename attribute TCAA_ACT_TIME_FILTER --> TCAA_ACT_TIME_DELTA

iii) Rename variable jiffy_filter --> jiffy_since
iv) Rename msecs_filter --> msecs_since
v) get rid of unused cb->args[0] and rename cb->args[4] to cb->args[0]

Earlier Changes
----------------
- Jiri mostly on names of things.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      764646b0
    • J
      net sched actions: add time filter for action dumping · e62e484d
      由 Jamal Hadi Salim 提交于 
      This patch adds support for filtering based on time since last used.
When we are dumping a large number of actions it is useful to
have the option of filtering based on when the action was last
used to reduce the amount of data crossing to user space.

With this patch the user space app sets the TCA_ROOT_TIME_DELTA
attribute with the value in milliseconds with "time of interest
since now".  The kernel converts this to jiffies and does the
filtering comparison matching entries that have seen activity
since then and returns them to user space.
Old kernels and old tc continue to work in legacy mode since
they dont specify this attribute.

Some example (we have 400 actions bound to 400 filters); at
installation time. Using updated when tc setting the time of
interest to 120 seconds earlier (we see 400 actions):
prompt$ hackedtc actions ls action gact since 120000| grep index | wc -l
400

go get some coffee and wait for > 120 seconds and try again:

prompt$ hackedtc actions ls action gact since 120000 | grep index | wc -l
0

Lets see a filter bound to one of these actions:
....
filter pref 10 u32
filter pref 10 u32 fh 800: ht divisor 1
filter pref 10 u32 fh 800::800 order 2048 key ht 800 bkt 0 flowid 1:10  (rule hit 2 success 1)
  match 7f000002/ffffffff at 12 (success 1 )
    action order 1: gact action pass
     random type none pass val 0
     index 23 ref 2 bind 1 installed 1145 sec used 802 sec
    Action statistics:
    Sent 84 bytes 1 pkt (dropped 0, overlimits 0 requeues 0)
    backlog 0b 0p requeues 0
....

that coffee took long, no? It was good.

Now lets ping -c 1 127.0.0.2, then run the actions again:
prompt$ hackedtc actions ls action gact since 120 | grep index | wc -l
1

More details please:
prompt$ hackedtc -s actions ls action gact since 120000

    action order 0: gact action pass
     random type none pass val 0
     index 23 ref 2 bind 1 installed 1270 sec used 30 sec
    Action statistics:
    Sent 168 bytes 2 pkt (dropped 0, overlimits 0 requeues 0)
    backlog 0b 0p requeues 0

And the filter?

filter pref 10 u32
filter pref 10 u32 fh 800: ht divisor 1
filter pref 10 u32 fh 800::800 order 2048 key ht 800 bkt 0 flowid 1:10  (rule hit 4 success 2)
  match 7f000002/ffffffff at 12 (success 2 )
    action order 1: gact action pass
     random type none pass val 0
     index 23 ref 2 bind 1 installed 1324 sec used 84 sec
    Action statistics:
    Sent 168 bytes 2 pkt (dropped 0, overlimits 0 requeues 0)
    backlog 0b 0p requeues 0
Signed-off-by: NJamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      e62e484d
    • J
      net sched actions: dump more than TCA_ACT_MAX_PRIO actions per batch · 90825b23
      由 Jamal Hadi Salim 提交于 
      When you dump hundreds of thousands of actions, getting only 32 per
dump batch even when the socket buffer and memory allocations allow
is inefficient.

With this change, the user will get as many as possibly fitting
within the given constraints available to the kernel.

The top level action TLV space is extended. An attribute
TCA_ROOT_FLAGS is used to carry flags; flag TCA_FLAG_LARGE_DUMP_ON
is set by the user indicating the user is capable of processing
these large dumps. Older user space which doesnt set this flag
doesnt get the large (than 32) batches.
The kernel uses the TCA_ROOT_COUNT attribute to tell the user how many
actions are put in a single batch. As such user space app knows how long
to iterate (independent of the type of action being dumped)
instead of hardcoded maximum of 32 thus maintaining backward compat.

Some results dumping 1.5M actions below:
first an unpatched tc which doesnt understand these features...

prompt$ time -p tc actions ls action gact | grep index | wc -l
1500000
real 1388.43
user 2.07
sys 1386.79

Now lets see a patched tc which sets the correct flags when requesting
a dump:

prompt$ time -p updatedtc actions ls action gact | grep index | wc -l
1500000
real 178.13
user 2.02
sys 176.96

That is about 8x performance improvement for tc app which sets its
receive buffer to about 32K.
Signed-off-by: NJamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      90825b23
    • J
      net sched actions: Use proper root attribute table for actions · df823b02
      由 Jamal Hadi Salim 提交于 
      Bug fix for an issue which has been around for about a decade.
We got away with it because the enumeration was larger than needed.

Fixes: 7ba699c6 ("[NET_SCHED]: Convert actions from rtnetlink to new netlink API")
Suggested-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NJamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      df823b02
    • J
      net netlink: Add new type NLA_BITFIELD32 · 64c83d83
      由 Jamal Hadi Salim 提交于 
      Generic bitflags attribute content sent to the kernel by user.
With this netlink attr type the user can either set or unset a
flag in the kernel.

The value is a bitmap that defines the bit values being set
The selector is a bitmask that defines which value bit is to be
considered.

A check is made to ensure the rules that a kernel subsystem always
conforms to bitflags the kernel already knows about. i.e
if the user tries to set a bit flag that is not understood then
the _it will be rejected_.

In the most basic form, the user specifies the attribute policy as:
[ATTR_GOO] = { .type = NLA_BITFIELD32, .validation_data = &myvalidflags },

where myvalidflags is the bit mask of the flags the kernel understands.

If the user _does not_ provide myvalidflags then the attribute will
also be rejected.

Examples:
value = 0x0, and selector = 0x1
implies we are selecting bit 1 and we want to set its value to 0.

value = 0x2, and selector = 0x2
implies we are selecting bit 2 and we want to set its value to 1.
Suggested-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NJamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      64c83d83
    • A
      net: fec: Allow reception of frames bigger than 1522 bytes · fbbeefdd
      由 Andrew Lunn 提交于 
      The FEC Receive Control Register has a 14 bit field indicating the
longest frame that may be received. It is being set to 1522. Frames
longer than this are discarded, but counted as being in error.

When using DSA, frames from the switch has an additional header,
either 4 or 8 bytes if a Marvell switch is used. Thus a full MTU frame
of 1522 bytes received by the switch on a port becomes 1530 bytes when
passed to the host via the FEC interface.

Change the maximum receive size to 2048 - 64, where 64 is the maximum
rx_alignment applied on the receive buffer for AVB capable FEC
cores. Use this value also for the maximum receive buffer size. The
driver is already allocating a receive SKB of 2048 bytes, so this
change should not have any significant effects.

Tested on imx51, imx6, vf610.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      fbbeefdd
    • A
      net: fec: Issue error for missing but expected PHY · 9558df3a
      由 Andrew Lunn 提交于 
      If the PHY is missing but expected, e.g. because of a typ0 in the dt
file, it is not possible to open the interface. ip link returns:

RTNETLINK answers: No such device

It is not very obvious what the problem is. Add a netdev_err() in this
case to make it easier to debug the issue.

[   21.409385] fec 2188000.ethernet eth0: Unable to connect to phy
RTNETLINK answers: No such device
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Acked-by: NFugang Duan <fugang.duan@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      9558df3a
    • D
      Merge branch 'dsa-lan9303-Fix-MDIO-issues' · 509394e8
      由 David S. Miller 提交于 
      Egil Hjelmeland says:

====================
net: dsa: lan9303: Fix MDIO issues.

This series fix the MDIO interface for the lan9303 DSA driver.
Bugs found after testing on actual HW.

This series is extracted from the first patch of my first large
series. Significant changes from that version are:
 - use mdiobus_write_nested, mdiobus_read_nested.
 - EXPORT lan9303_indirect_phy_ops

Unfortunately I do not have access to i2c based system for
testing.

Changes from first version:
 - Change EXPORT_SYMBOL to EXPORT_SYMBOL_GPL
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      509394e8
    • E
      net: dsa: lan9303: MDIO access phy registers directly · 2c340898
      由 Egil Hjelmeland 提交于 
      Indirect access (PMI) to phy register only work in I2C mode. In
MDIO mode phy registers must be accessed directly. Introduced
struct lan9303_phy_ops to handle the two modes.
Signed-off-by: NEgil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      2c340898
    • E
      net: dsa: lan9303: Renamed indirect phy access functions · 9e866e5d
      由 Egil Hjelmeland 提交于 
      Preparing for the following fix of MDIO phy access:

Renamed functions that access PHY 1 and 2 indirectly through PMI
registers.

 lan9303_port_phy_reg_wait_for_completion() to
 lan9303_indirect_phy_wait_for_completion()

 lan9303_port_phy_reg_read() to
 lan9303_indirect_phy_read()

 lan9303_port_phy_reg_write() to
 lan9303_indirect_phy_write()

Also changed "val" parameter of lan9303_indirect_phy_write() to u16,
for clarity.
Signed-off-by: NEgil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      9e866e5d
    • E
      net: dsa: lan9303: Multiply by 4 to get MDIO register · ab78acb1
      由 Egil Hjelmeland 提交于 
      lan9303_mdio_write()/_read() must multiply register number by 4 to get
offset.

Added some commments to the register definitions.
Signed-off-by: NEgil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      ab78acb1
    • E
      net: dsa: lan9303: Fix lan9303_detect_phy_setup() for MDIO · d329ac88
      由 Egil Hjelmeland 提交于 
      Handle that MDIO read with no response return 0xffff.
Signed-off-by: NEgil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      d329ac88
  5. 30 7月, 2017 6 次提交
    • D
      Merge branch 'ethtool-fec' · 736b9b9c
      由 David S. Miller 提交于 
      Roopa Prabhu says:

====================
ethtool: support for forward error correction mode setting on a link

Forward Error Correction (FEC) modes i.e Base-R
and Reed-Solomon modes are introduced in 25G/40G/100G standards
for providing good BER at high speeds. Various networking devices
which support 25G/40G/100G provides ability to manage supported FEC
modes and the lack of FEC encoding control and reporting today is a
source for interoperability issues for many vendors.
FEC capability as well as specific FEC mode i.e. Base-R
or RS modes can be requested or advertised through bits D44:47 of base link
codeword.

This patch set intends to provide option under ethtool to manage and
report FEC encoding settings for networking devices as per IEEE 802.3
bj, bm and by specs.

v2 :
        - minor patch format fixes and typos pointed out by Andrew
        - there was a pending discussion on the use of 'auto' vs
          'automatic' for fec settings. I have left it as 'auto'
          because in most cases today auto is used in place of
          automatic to represent automatically generated values.
          We use it in other networking config too. I would prefer
          leaving it as auto.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      736b9b9c
    • C
      cxgb4: ethtool forward error correction management support · 7fece840
      由 Casey Leedom 提交于 
      Signed-off-by: NCasey Leedom <leedom@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      7fece840
    • C
      cxgb4: core hardware/firmware support for Forward Error Correction on a link · 158a5c0a
      由 Casey Leedom 提交于 
      Signed-off-by: NCasey Leedom <leedom@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      158a5c0a
    • V
      net: ethtool: add support for forward error correction modes · 1a5f3da2
      由 Vidya Sagar Ravipati 提交于 
      Forward Error Correction (FEC) modes i.e Base-R
and Reed-Solomon modes are introduced in 25G/40G/100G standards
for providing good BER at high speeds. Various networking devices
which support 25G/40G/100G provides ability to manage supported FEC
modes and the lack of FEC encoding control and reporting today is a
source for interoperability issues for many vendors.
FEC capability as well as specific FEC mode i.e. Base-R
or RS modes can be requested or advertised through bits D44:47 of
base link codeword.

This patch set intends to provide option under ethtool to manage
and report FEC encoding settings for networking devices as per
IEEE 802.3 bj, bm and by specs.

set-fec/show-fec option(s) are designed to provide control and
report the FEC encoding on the link.

SET FEC option:
root@tor: ethtool --set-fec  swp1 encoding [off | RS | BaseR | auto]

Encoding: Types of encoding
Off    :  Turning off any encoding
RS     :  enforcing RS-FEC encoding on supported speeds
BaseR  :  enforcing Base R encoding on supported speeds
Auto   :  IEEE defaults for the speed/medium combination

Here are a few examples of what we would expect if encoding=auto:
- if autoneg is on, we are  expecting FEC to be negotiated as on or off
  as long as protocol supports it
- if the hardware is capable of detecting the FEC encoding on it's
      receiver it will reconfigure its encoder to match
- in absence of the above, the configuration would be set to IEEE
  defaults.

>From our  understanding , this is essentially what most hardware/driver
combinations are doing today in the absence of a way for users to
control the behavior.

SHOW FEC option:
root@tor: ethtool --show-fec  swp1
FEC parameters for swp1:
Active FEC encodings: RS
Configured FEC encodings:  RS | BaseR

ETHTOOL DEVNAME output modification:

ethtool devname output:
root@tor:~# ethtool swp1
Settings for swp1:
root@hpe-7712-03:~# ethtool swp18
Settings for swp18:
    Supported ports: [ FIBRE ]
    Supported link modes:   40000baseCR4/Full
                            40000baseSR4/Full
                            40000baseLR4/Full
                            100000baseSR4/Full
                            100000baseCR4/Full
                            100000baseLR4_ER4/Full
    Supported pause frame use: No
    Supports auto-negotiation: Yes
    Supported FEC modes: [RS | BaseR | None | Not reported]
    Advertised link modes:  Not reported
    Advertised pause frame use: No
    Advertised auto-negotiation: No
    Advertised FEC modes: [RS | BaseR | None | Not reported]
<<<< One or more FEC modes
    Speed: 100000Mb/s
    Duplex: Full
    Port: FIBRE
    PHYAD: 106
    Transceiver: internal
    Auto-negotiation: off
    Link detected: yes

This patch includes following changes
a) New ETHTOOL_SFECPARAM/SFECPARAM API, handled by
  the new get_fecparam/set_fecparam callbacks, provides support
  for configuration of forward error correction modes.
b) Link mode bits for FEC modes i.e. None (No FEC mode), RS, BaseR/FC
  are defined so that users can configure these fec modes for supported
  and advertising fields as part of link autonegotiation.
Signed-off-by: NVidya Sagar Ravipati <vidya.chowdary@gmail.com>
Signed-off-by: NDustin Byford <dustin@cumulusnetworks.com>
Signed-off-by: NRoopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      1a5f3da2
    • D
      Merge branch 'netvsc-minor-fixes-and-optimization' · fe21b269
      由 David S. Miller 提交于 
      Stephen Hemminger says:

====================
netvsc: minor fixes and optimization

This is a subset of earlier submission with a few more fixes
found during testing. The are two small optimizations, one is to
better manage the receive completion ring, and the other is removing
one unneeded level of indirection.

Will submit the improved VF support and buffer sizing in a later
patch so they get more review.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      fe21b269
    • S
      netvsc: signal host if receive ring is emptied · f4e40363
      由 stephen hemminger 提交于 
      Latency improvement related to NAPI conversion.
If all packets are processed from receive ring then need
to signal host.
Signed-off-by: NStephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      f4e40363