This is not used anymore with the new fragmentation, and it might
actually mess up the bonding code because find_router() assumes it
is only called once per packet.
Signed-off-by: NSimon Wunderlich <simon@open-mesh.com>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NAntonio Quartulli <antonio@meshcoding.com>

The module prints a warning when the MTU on the hard interface is too
small to transfer payload traffic without fragmentation. The required
MTU is calculated based on the encapsulation header size. If network
coding is compild into the module its header size is taken into
account as well.
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NAntonio Quartulli <antonio@meshcoding.com>

the icmp and the icmp_rr packets share the same initial
fields since they use the same code to be processed and
forwarded.

Extract the common fields and put them into a separate
struct so that future ICMP packets can be easily added
without bloating the packet definition.

However, keep the seqno field outside of the newly created
common header because future ICMP types may require a
bigger sequence number space.

This change breaks compatibility due to fields reordering
in the ICMP headers.
Signed-off-by: NAntonio Quartulli <antonio@open-mesh.com>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>

When comparing a network ordered value with a constant, it
is better to convert the constant at compile time by means
of htons() instead of converting the value at runtime using
ntohs().

This refactoring may slightly improve the code performance.

Moreover substitute __constant_htons() with htons() since
the latter increase readability and it is smart enough to be
as efficient as the former
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Acked-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>

Non-broadcast packets larger than MTU are fragmented and sent with
an encapsulating header. Up to 16 fragments are supported, which are
sent in reverse order on the wire to allow minimal memory copying when
creating fragments.
Signed-off-by: NMartin Hundebøll <martin@hundeboll.net>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NAntonio Quartulli <antonio@meshcoding.com>

Fragments arriving at their destination are buffered for later merge.
Merged packets are passed to the main receive function as had they never
been fragmented.

Fragments are forwarded without merging if the MTU of the outgoing
interface is smaller than the size of the merged packet.
Signed-off-by: NMartin Hundebøll <martin@hundeboll.net>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NAntonio Quartulli <antonio@meshcoding.com>

Remove the existing fragmentation code before adding the new version
and delete unicast.{h,c}.

batadv_unicast_send_skb() is moved to send.c and renamed to
batadv_send_skb_unicast().

fragmentation entry in sysfs (bat_priv->fragmentation) is kept for use in
the new fragmentation code.

BATADV_UNICAST_FRAG packet type is renamed to BATADV_FRAG for use in the
new fragmentation code.
Signed-off-by: NMartin Hundebøll <martin@hundeboll.net>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NAntonio Quartulli <antonio@meshcoding.com>

Signed-off-by: NAntonio Quartulli <ordex@autistici.org>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>

In case of a VLAN tagged frame the ethhdr pointer is
moved forward by 4 bytes so that the offset of h_proto
in struct ethhdr matches the real
h_vlan_encapsulated_proto address in the skb. While this
trickery is correct it makes the code harder to understand
and may lead to bugs in case of re-use of ethhdr for other
purposes.

This patch introduces a proto variable to make things
cleaner and easier to understand.
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>

batadv_tt_global_entry_free_ref uses call_rcu to schedule a
function which will only free the global entry itself.

For this reason call_rcu is useless and kfree_rcu can be
used to simplify the code.
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>

batadv_tt_global_add_orig is neither used nor implemented
anymore, therefore it is possible to remove its declaration
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>

batadv_tt_global_add is not used anymore outside of the TT
code thanks to the TVLV implementation. It can therefore be
declared as static

Last user has been removed by 3de4e64df0f1326db7cc0ef25f5af8522850252d
("batman-adv: tvlv - convert roaming adv packet to use tvlv unicast packets")

Moreover make it return bool since its result can be either 0 or 1.
Reported-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>

Adding host information for record route is only required for ICMP
requests and replys, and should not be added to just any (future?)
packet type.
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NAntonio Quartulli <antonio@meshcoding.com>

1) We need to take a timestamp only for skb that should be cloned.

Other skbs are not in write queue and no rtt estimation is done on them.

2) the unlikely() hint is wrong for receivers (they send pure ACK)
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: MF Nowlan <fitz@cs.yale.edu>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-By: NYuchung Cheng <ycheng@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In commit 634fb979 ("inet: includes a sock_common in request_sock")
I forgot that the two ports in sock_common do not have same byte order :

skc_dport is __be16 (network order), but skc_num is __u16 (host order)

So sparse complains because ir_loc_port (mapped into skc_num) is
considered as __u16 while it should be __be16

Let rename ir_loc_port to ireq->ir_num (analogy with inet->inet_num),
and perform appropriate htons/ntohs conversions.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Reported-by: NWu Fengguang <fengguang.wu@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

sk_pacing_rate is read by sch_fq packet scheduler at any time,
with no synchronization, so make sure we update it in a
sensible way. ACCESS_ONCE() is how we instruct compiler
to not do stupid things, like using the memory location
as a temporary variable.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

TCP listener refactoring, part 5 :

We want to be able to insert request sockets (SYN_RECV) into main
ehash table instead of the per listener hash table to allow RCU
lookups and remove listener lock contention.

This patch includes the needed struct sock_common in front
of struct request_sock

This means there is no more inet6_request_sock IPv6 specific
structure.

Following inet_request_sock fields were renamed as they became
macros to reference fields from struct sock_common.
Prefix ir_ was chosen to avoid name collisions.

loc_port   -> ir_loc_port
loc_addr   -> ir_loc_addr
rmt_addr   -> ir_rmt_addr
rmt_port   -> ir_rmt_port
iif        -> ir_iif
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

skb_gro_receive() is currently limited to 16 or 17 MSS per GRO skb,
typically 24616 bytes, because it fills up to MAX_SKB_FRAGS frags.

It's relatively easy to extend the skb using frag_list to allow
more frags to be appended into the last sk_buff.

This still builds very efficient skbs, and allows reaching 45 MSS per
skb.

(45 MSS GRO packet uses one skb plus a frag_list containing 2 additional
sk_buff)

High speed TCP flows benefit from this extension by lowering TCP stack
cpu usage (less packets stored in receive queue, less ACK packets
processed)

Forwarding setups could be hurt, as such skbs will need to be
linearized, although its not a new problem, as GRO could already
provide skbs with a frag_list.

We could make the 65536 bytes threshold a tunable to mitigate this.

(First time we need to linearize skb in skb_needs_linearize(), we could
lower the tunable to ~16*1460 so that following skb_gro_receive() calls
build smaller skbs)
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is a enhancement.

for the first node in fib_trie, newpos is 0, bit is 1.
Only for the leaf or node with unmatched key need calc pos.
Signed-off-by: Nbaker.zhang <baker.kernel@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The vis flag is not needed anymore, and since we do a compat bump we
can start with the first bit again
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NAntonio Quartulli <antonio@meshcoding.com>

As we decreased the struct size from 26 to 24 byte, we can remove
__packed as the compiler will not add any more padding.
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NAntonio Quartulli <antonio@meshcoding.com>

Reordering the packet type numbers allows us to handle unicast
packets in a general way - even if we don't know the specific packet
type, we can still forward it. There was already code handling
this for a couple of unicast packets, and this is the more
generalized version to do that.
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NAntonio Quartulli <antonio@meshcoding.com>

Since we removed the __packed from most of the packets, we should
make sure that the offset generated by the compiler are correct for
sent/received data.
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NAntonio Quartulli <antonio@meshcoding.com>

This is replaced by a userspace program, we don't need this
functionality to bloat the kernel.
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NAntonio Quartulli <antonio@meshcoding.com>

Client flags from bit 0 to 7 are sent over the wire.
BATADV_TT_CLIENT_TEMP is a local flag and is not supposed
to be sent to the network. Therefore it has occupy a
higher bit.
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>

CRC32C has to be preferred to CRC16 because of its possible
HW native support and because of the reduced collision
probability. With this change the Translation Table
component now uses CRC32C to compute the local and global
table checksum.
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>

Instead of generating roaming specific packets the TVLV unicast API is
used to send roaming information.
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NAntonio Quartulli <antonio@meshcoding.com>

Instead of generating TT specific packets the TVLV unicast API is used
to send translation table data.
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NAntonio Quartulli <antonio@meshcoding.com>

The translation table meta data (version number, crc checksum, etc)
as well as the translation table diff propgated within OGMs now uses
the newly introduced tvlv infrastructure.
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NAntonio Quartulli <antonio@meshcoding.com>

Create network coding container to announce network coding
capabilities (if enabled).
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NAntonio Quartulli <antonio@meshcoding.com>

Create DAT container to announce DAT capabilities (if enabled).
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NAntonio Quartulli <antonio@meshcoding.com>

Prior to this patch batman-adv read the advertised uplink bandwidth
from userspace and compressed this information into a single byte
called "gateway class".
Now the download & upload bandwidth information is sent as-is. No
userspace change is necessary since the sysfs API always allowed
to specify a bandwidth.
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NSpyros Gasteratos <morfeas3000@gmail.com>
Signed-off-by: NAntonio Quartulli <antonio@meshcoding.com>

The goal is to provide the infrastructure for sending, receiving and
parsing information 'containers' while preserving backward
compatibility. TVLV (based on the commonly known Type Length Value
technique) was chosen as the format for those containers. Even if a
node does not know the tvlv type of a certain container it can simply
skip the current container and proceed with the next. Past experience
has shown features evolve over time, so a 'version' field was added
right from the start to allow differentiating between feature
variants - hence the name: T(ype) V(ersion) L(ength) V(alue).

This patch introduces the basic TVLV infrastructure:
 * register / unregister tvlv containers to be sent with each OGM
   (on primary interfaces only)
 * register / unregister callback handlers to be called upon
   finding the corresponding tvlv type in a tvlv buffer
 * unicast tvlv send / receive API calls
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NSpyros Gasteratos <morfeas3000@gmail.com>
Signed-off-by: NAntonio Quartulli <antonio@meshcoding.com>

With this change batman-adv is breaking compatibility with
older versions and it is moving to compat-version 15.
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NMartin Hundebøll <martin@hundeboll.net>
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>

CONFIG_IPV6=n is still a valid choice ;)

It appears we can remove dead code.
Reported-by: NWu Fengguang <fengguang.wu@intel.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

At this point sk might contain garbage.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

TCP listener refactoring, part 4 :

To speed up inet lookups, we moved IPv4 addresses from inet to struct
sock_common

Now is time to do the same for IPv6, because it permits us to have fast
lookups for all kind of sockets, including upcoming SYN_RECV.

Getting IPv6 addresses in TCP lookups currently requires two extra cache
lines, plus a dereference (and memory stall).

inet6_sk(sk) does the dereference of inet_sk(__sk)->pinet6

This patch is way bigger than its IPv4 counter part, because for IPv4,
we could add aliases (inet_daddr, inet_rcv_saddr), while on IPv6,
it's not doable easily.

inet6_sk(sk)->daddr becomes sk->sk_v6_daddr
inet6_sk(sk)->rcv_saddr becomes sk->sk_v6_rcv_saddr

And timewait socket also have tw->tw_v6_daddr & tw->tw_v6_rcv_saddr
at the same offset.

We get rid of INET6_TW_MATCH() as INET6_MATCH() is now the generic
macro.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

TCP listener refactoring, part 3 :

Our goal is to hash SYN_RECV sockets into main ehash for fast lookup,
and parallel SYN processing.

Current inet_ehash_bucket contains two chains, one for ESTABLISH (and
friend states) sockets, another for TIME_WAIT sockets only.

As the hash table is sized to get at most one socket per bucket, it
makes little sense to have separate twchain, as it makes the lookup
slightly more complicated, and doubles hash table memory usage.

If we make sure all socket types have the lookup keys at the same
offsets, we can use a generic and faster lookup. It turns out TIME_WAIT
and ESTABLISHED sockets already have common lookup fields for IPv4.

[ INET_TW_MATCH() is no longer needed ]

I'll provide a follow-up to factorize IPv6 lookup as well, to remove
INET6_TW_MATCH()

This way, SYN_RECV pseudo sockets will be supported the same.

A new sock_gen_put() helper is added, doing either a sock_put() or
inet_twsk_put() [ and will support SYN_RECV later ].

Note this helper should only be called in real slow path, when rcu
lookup found a socket that was moved to another identity (freed/reused
immediately), but could eventually be used in other contexts, like
sock_edemux()

Before patch :

dmesg | grep "TCP established"

TCP established hash table entries: 524288 (order: 11, 8388608 bytes)

After patch :

TCP established hash table entries: 524288 (order: 10, 4194304 bytes)
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Steinar reported FQ pacing was not working for UDP flows.

It looks like the initial sk->sk_pacing_rate value of 0 was
a wrong choice. We should init it to ~0U (unlimited)

Then, TCA_FQ_FLOW_DEFAULT_RATE should be removed because it makes
no real sense. The default rate is really unlimited, and we
need to avoid a zero divide.
Reported-by: NSteinar H. Gunderson <sesse@google.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the calculation of the nlmsg size, by adding the missing
nla_total_size().

Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>