ath6kl: If wow deepsleep pno suspend failure driver will choose cutpower.
in this scenario MMC_PM_KEEP_POWER should be cleared so that mmc will power
off the ar6000

kvalo: remove extra parenthesis
Signed-off-by: NMing Jiang <mjiang@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Set max_scan_ssids and max_sched_scan_ssids to same value. These use the
same probed SSID list, so there is no point in using different maximum
number of SSIDs.

Clear probed SSID entries that are not used. This was already done for
sched_scan, but not for scan. Be consistent and clear the table for both
cases to avoid leaving bogus entries.

In addition, share the same function for setting the probed SSIDs for
scan and sched_scan paths. This fixes setting of wildcard SSID flag
(ANY_SSID_FLAG) and changes the scan path to use probed SSID index
consistently (i.e., start with 0 similarly to sched_scan; firmware
will handle the needed internal mapping).
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

ath6kl does not support Probe Response offloading for Interworking (IEEE
802.11u), so remove the incorrectly added capability flag for it.
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Background scan interval should not be modified while starting
schedule scanning as it changes the bg scan interval when connected to AP.
Use the currently configured interval instead.

kvalo: improve commit log
Signed-off-by: NSubramania Sharma <sharmat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Added a new member bg_scan_period in struct ath6kl_vif
to retain background scan period value configured via debugfs
entry 'bgscan_interval'. This backup is needed in schedule scan
path while configuring scan parameters.
Signed-off-by: NRaja Mani <rmani@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

We can remove the NULL check here.  It triggers a Smatch warning because
list_first_entry() never is NULL and people who check for it normally
intend to check for list_empty() instead.  In these cases however,
we've already verified that the lists are not empty.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

kvalo: do the same changes for ar6004 hw1.2 as well

Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: NTim Gardner <tim.gardner@canonical.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Aafter wlan interface is down WLAN_ENABLED flags will be cleared and
deepsleep_suspend function will be blocked in this senario. This patch
allows deepsleep_suspend function when wlan interface down by removed
the WLAN_ENABLED flag checking.

kvalo: fix commit log
Signed-off-by: NMing Jiang <mjiang@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

System crash because of NULL pointer reference due to
cleanup_scatter is not implemented for USB.
Signed-off-by: NRay Chen <raychen@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Found by checkpatch:

WARNING: quoted string split across lines
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

If, in
drivers/net/wireless/ath/ath6kl/debug.c::ath6kl_fwlog_block_read(),
the call to wait_for_completion_interruptible() returns -ERESTARTSYS
then we'll return without freeing the (as yet unused) memory we
allocated for 'buf' - thus leaking it.
Signed-off-by: NJesper Juhl <jj@chaosbits.net>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Add the necessary change for AR6004 1.2 chip support
Signed-off-by: NRay Chen <raychen@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Currently rsn capability is not set when it is not available in
rsn IE. Set it to 0 in firmware when it is not there in the ie to
make sure host and target are consistent.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

alignment is not taken care in accessing pairwise cipher and AKM suite
count which are parsed from rsn ie. Fix this alignment issue.
Reported-by: NJoe Perches <joe@perches.com>
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

If an ath6kl AP vif is beaconing on one channel, and a STA vif
associates on a different channel, a WMI_DISCONNECT event will be sent
to the AP vif. Make the AP vif follow the STA interface, and notify
userspace.

kvalo: fix a sparse warning with vif->next_chan
Signed-off-by: NThomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Use a more current logging style.
Make sure all output is prefixed appropriately.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

RSN capability field of RSN IE which is generated (which is what really
advertised in beacon/probe response) differs from the one generated in
wpa_supplicant. This inconsistency in rsn IE results in 4-way handshake
failure. To fix this, configure rsn capability used in wpa_supplicant
in firmware using a new wmi command, WMI_SET_IE_CMDID. There is a bit
(ATH6KL_FW_CAPABILITY_RSN_CAP_OVERRIDE) in fw_capabilities to advertise
this support to driver.
Signed-off-by: NSubramania Sharma <sharmat@qca.qualcomm.com>
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This patch disables HT in start_ap if the type of the channel on
which the AP mode is going to be operating is non-HT. HT is enabled
with default ht cap setting if the operating channel is going to be
11n.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

HT40 is not supported in 2.4Ghz.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Using interface 0 for p2p causes target assert. This is because
interface 0 is always initialized to non-p2p operations. Fix this
issue by initializing all the interfaces for p2p when fw is capable
of dynamic interface switching. When fw is not capable of dynamic
switching, make sure p2p is not brought up on interface which is
not initialized for this purpose.

Reported-by: Naveen Singh navesing@qca.qualcomm.com
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

net_stats.multicast is updated with the count of received multicast packets.

kvalo: indentation changes
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

When a scan request is pending while going to suspend, any new
scan request after resume will fail. So, cancel all scan requests
in all the vifs before moving to suspend state.
Signed-off-by: NPingYang Zhang <pingzhan@qca.qualcomm.com>
Signed-off-by: NVivek Natarajan <nataraja@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Sometimes it has been observed that allocating a contiguous memory
of more than 100K fails with kmalloc. This has been modified to
use vmalloc instead.
Signed-off-by: NPingYang Zhang <pingzhan@qca.qualcomm.com>
Signed-off-by: NVivek Natarajan <nataraja@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

After connect command, send scan params WMI command to
set background scan period. If period value is zero
send 0xffff as bg scan period to disable bg scan.
Set default bg scan period to be 60 seconds if
not specified.

This patch depends on below patch
cfg80211: Add background scan period attribute.

kvalo: fix open parenthesis alignment
Signed-off-by: NBala Shanmugam <bkamatch@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

In current code, Scan request info is recorded in vif->scan_req
after sending SCAN request to the firmware in ath6kl_cfg80211_scan().

In some corner cases, firmware sends SCAN_COMPLETE event immediately
when it receives SCAN request, which internally executes scan
complete event handler ath6kl_cfg80211_scan_complete_event() first.
So, Scan completion handler will a get a chance to executed even
before storing scan request info in ath6kl_cfg80211_scan().

Scan completion handler never report SCAN_COMPLETE event to
cfg80211 if scan request info(vif->scan_req) is NULL. This leads
to scan failure issue ("Device or resource busy error") during
next SCAN request from the user space. This patch ensures that scan
request info is stored before sending SCAN request.
Signed-off-by: NRaja Mani <rmani@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Now, with HTC pipe, it's possible to fully support USB version of AR6004.

Based on code by Kevin Fang.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This is needed for USB.

Based on code by Kevin Fang.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

In preparation for adding HTC pipe implementation add htc-ops.h to make
it possible dynamically choose which HTC type is used.

Needed for full USB support.

Based on the code by Ray Chen <raychen@qca.qualcomm.com>.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: NRay Chen <raychen@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Void pointers are bad.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Needed when using USB.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Needed by the USB code.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It's also needed by the USB code.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This is needed by the USB code. Also while at it replace one void pointer
with a properly typed pointer.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Ram reserved size is not needed with ar6004.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Configure the inactivity timeout passed in start_ap() to
firmware. This capability is advertised only when fw supports
it, there is a new bit (ATH6KL_FW_CAPABILITY_INACTIVITY_TIMEOUT)
in firmware capability ie for driver to learn fw's capability.
After the fw finds out the station is inactive, it will probe
the station with null func frames. By default, the timeout is
10 secs.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Adding below steps helps to get good power numbers
in deep sleep suspend path,

    * Disable WOW mode.
    * Flush data packets and wait for all control packets.
      to be cleared in TX path before deep sleep suspend.
    * Set host sleep mode to SLEEP.

Below steps are added to perform the recovery action
while the system resume from deep sleep,

     * Set host sleep mode to AWAKE.
     * Reset scan parameters to default value.

In addition, Debug prints are added to track deep sleep
suspend/resume state.
Signed-off-by: NRaja Mani <rmani@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The piece of code used in ath6kk_wow_suspend function
to configure the host sleep mode is needed in deep sleep
case also.

Moving that portion to a separate function called
ath6kl_update_host_mode() would be helpful to avoid
the duplication of the same code in deep sleep path.

There is no functional change.

kvalo: move inline functions to cfg80211.c and fix a long line
Signed-off-by: NRaja Mani <rmani@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Dump htc header along with the warning message when the request
to Rx with invalid frame length is detected.

kvalo: fix open parenthesis alignment
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

If the device disconnects from an AP when it is in suspending state. You will
get the following message from wpa_supplicant after waking the device up and
sending scan request:

"Scan trigger failed: ret=-16 (Device or resource busy)"

Fix the issue by sending a scan complete event before starting scheduled
scan.

kvalo: cosmetic changes to commit log
Signed-off-by: NIsaac.li <shonmou@gmail.com>
Tested-by: NRaja Mani <rmani@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Make sure printf formats and arguments match.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>