It was superfluous and confusing. It's better to
define the structure explicitly.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

There's no need to store rate values in hw_value.
This frees up the hw_value for better future use.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Prepare the code for future changes so that new
code can refer to rate-related stuff without
forward declarations.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This patch introduces tdls without tdls peer uapsd and tdls channel switching.
Transmitting tdls data frames works only for ethernet type frames, that's why
data addressed to tdls sta is in ethernet format.

This patch depends on commit c23e31cf ("mac80211: initialize rate control
earlier for tdls station").
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NMarek Kwaczynski <marek.kwaczynski@tieto.com>
Signed-off-by: NMarek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Currently station counting functions
(inc_num_stations/dec_num_stations) does not handle
tdls type of stations. Tdls station should be counted
because it consumes peer in firmware. Only not tdls
stations are excluded from this counting.
Signed-off-by: NMarek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Peer type was hardcoded to default value.
For future implementation it is required
to make is configurable.
Signed-off-by: NMarek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: NMarek Kwaczynski <marek.kwaczynski@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

There are a few different tx paths depending on
firmware and frame itself.

Creating a uniform decision will make it possible
to switch between different txmode easier, both
for testing and for future features as well.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NMarek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

If htt.freq isn't cleared and contains garbage fw
may discard tx packets. Prevent this from
happening by clearing htt.freq properly.

Possible manifestation of the problem could be not
being able to send auth request/response frames on
firmware with HTT >= 3.4 (when freq param was
introduced), e.g. on qca6174.

Fixes: 8d6d3624 ("ath10k: fix offchan reliability")
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Add support for WOW disconnect and magic-packet.
Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Now that ANI is enabled by default, allow user to disable or enable ANI feature
from debugfs

echo 0|1 > /sys/kernel/debug/ieee80211/phyX/ath10k/ani_enable
Signed-off-by: NAshok Raj Nagarajan <arnagara@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

ANI helps to improve connectvity and performance in a noisy environment.
Enabling this feature would help the user experience a better and stable
wireless connection in a noisy environmnet. This feature is currently not
enabled for ath10k. Enable this feature by default.
Signed-off-by: NAshok Raj Nagarajan <arnagara@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Enable channel 144 on 5GHz band since 802.11ac introduced it.
Signed-off-by: NPeter Oh <poh@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Thermal throttling is not handled in software restart and device
bootup. Also it needs to be configured whenever quiet period got
updated. Fix that.
Reported-by: NMatthias Kaehlcke <mka@google.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

By default rts protection is enabled in firmware for the second
rateset. Currently ath10k selects RTS profile (only for software
retries), when legacy stations are associated or asked by mac80211.
On congested environment, when AP is running in HT/VHT mode and
there are no legacy clients associated, this will impact the
robustness. Also enabling RTS protection only for second rateset will
not impact performance on clear environment. Fix that.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Setup maximum number of associated stations supported in
AP/P2P_GO mode.

This allow hostapd/wpa_supplicant to play with that limit
and set more information (eg. P2P group limit bit for P2P_GO).
Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

NativeWifi tx mode expects QoS Data frames to be
delivered as Data frames with QoS part (e.g. tid)
being delievered out-of-band in fw tx command.

The QoS bit wasn't stripped before submitting to
firmware.

Stripping fixes two known problems:

 * qca6174 IOT with some APs, e.g.
   Cisco AIR-AP 1252 (which would crash after
   ath10k association). Some ath9k APs would
   crash as well.

 * sniffing own tx frames via radiotap because,
   e.g. wireshark was seeing QoS bit set but
   since QoS Control was stripped in ath10k it
   would parse beginning of LLC/SNAP

>From debugability point of view this removes the
ability to distinguish QoS from non-QoS frames
when sniffing own tx via radiotap. On the other
hand frames can be now parsed correctly without
special software modification.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

While testing with older supplicant, .drv_set_key() was failing due to
higher than ath10k firmware could handle key_index (WMI_MAX_KEY_INDEX == 3).

--
wpa_driver_nl80211_set_key: ifindex=15 alg=4 addr=0x7f02b129fbe3 key_idx=4 set_tx=0 seq_len=6 key_len=16
    broadcast key
nl80211: set_key failed; err=-22 Invalid argument)
wlan0: WPA: Failed to configure IGTK to the driver
wlan0: RSN: Failed to configure IGTK
--

In order to fix this case (PMF: AES-CMAC/IGTK) force the AES_CMAC cipher to
be handled by software.
Signed-off-by: NBartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Some firmware revisions (e.g. qca6174 with fw73)
don't deliver beacons to host reliably. This
causes random disconnects even in perfect
conditions. This is most visible with
multi-channel operation.

All available firmware revisions seem to support
beacon miss offloading so there shouldn't be any
problems.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Commit 370e5673 ("ath10k: fix broken traffic for 802.1x in client mode")
introduced a regression on WPA crypto. All keys were treated as if they were
WEP which resulted in WPA being incorrectly installed to fw/hw and subsequently
no traffic.
Reported-by: NMarek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Commit 54846213 ("ath10k: fix interrupt storm") introduced a
regression. The condition responsible for bringing up monitor vdev was broken
and it was never started for CAC so effectivelly CAC would not detect radar
pulses.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Mistakenly v1 of `ath10k: fix AP/IBSS CSA with
template based fw`
(81a9a17d) was
applied.

This patch applies the missing bits from v2:
 * remove unnecessary locking
 * add some (sanity) checks

There are no practical functionality differences
between v1 and v2.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Promiscuous mode is enabled when wlan interface is added to
bridge. ath10k creates a monitor mode when promiscuous mode
is enabled. When monitor vdev is running along with other
vdev(s) there is a huge number of interrupts generated
especially in noisy condition. Fix this by not enabling
promiscuous(monitor) mode when already a vdev is running.
As disabling promiscuous mode may have issues with 4-address
bridging in STA mode, the change is done specific to non-sta/ibss
mode types. This does not change the support of virtual interface of
type monitor along with other vdevs of any type.

This could fix management frame drop in fw due to unavailable
buffers because in monitor mode device receives everything seen
on the air. In noisy condition, disabling monitor mode helps assoc
go through without any issue.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This patches does not modify any functionality. Just a code move
so that ath10k_vdev_stop() can be used in ath10k_vdev_start_restart()
for any failure cases which involves vdev_stop().
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This improves coexistance with 11b legacy devices
on wmi-tlv and qca6174.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Firmware doesn't report a complete and
ready-to-use vht cap. Instead the driver is
supposed to fill in the missing bits related to
number of chains.

This effectively increases Compressed Steering
Number and Number of Sounding Dimensions in
AssocReq frames for devices with more than one RF
chain and should improve TxBF performance.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

When WEP keys are uploaded it's possible that
there are stations associated already (e.g. when
merging) without any keys. Static WEP needs an
explicit per-peer key upload.

Make sure to re-upload wep keys if necessary.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

When running 802.1x WEP keys must be installed
without pairwise-groupwise swap (which is
necessary for static WEP).
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

qca6174 with wmi-tlv firmware uses offloaded
beaconing scheme (i.e. templates). This requires a
little different approach when implementing CSA.

Add missing code to update CS count and report CSA
completion to mac80211. Without it channel switch
was never finished.

To avoid races during interface teardown data_lock
has been used to protect is_up and is_started so
they can be compared against before scheduling
count down work.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Not all firmware revisions have a proper
multi-interface client powersaving implementation,
e.g. qca6174 WLAN.RM.2.0-00073.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

qca6184 WLAN.RM.2.0-00073 has a bug in sta
powersave state machine and requires peer param to
be poked to enable the powersave.

Calling this unconditionally should be safe for
other chips/firmwares.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

802.11ad adds new a network type (PBSS) and changes the capability
field interpretation for the DMG (60G) band.
The same 2 bits that were interpreted as "ESS" and "IBSS" before are
re-used as a 2-bit field with 3 valid values (and 1 reserved). Valid
values are: "IBSS", "PBSS" (new) and "AP".

In order to get the BSS struct for the new PBSS networks, change the
cfg80211_get_bss() function to take a new enum ieee80211_bss_type
argument with the valid network types, as "capa_mask" and "capa_val"
no longer work correctly (the search must be band-aware now.)

The remaining bits in "capa_mask" and "capa_val" are used only for
privacy matching so replace those two with a privacy enum as well.
Signed-off-by: NDedy Lansky <dlansky@codeaurora.org>
[rewrite commit log, tiny fixes]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

If firmware advertises support for TxBF then the
driver has to instruct the firmware accordingly
during runtime. Without this patch connecting to
an AP with beamformer support would yield abysmal
Rx performance.

This has been tested with wmi-tlv and qca6174
while acting as a STA beamformee only.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Some firmware revisions don't notify host about
self-bss-peer removal until after associated vdev
is deleted. This has been observed with qca6174
WLAN.RM.2.0-00073 firmware.

This patch fixes AP teardown slowdowns and
prevents delays and warnings:

 ath10k_pci 0000:00:05.0: failed to remove peer for AP vdev 0: -110
 ath10k_pci 0000:00:05.0: removing stale peer xx:xx:xx:xx:xx:xx from vdev_id 0
 ath10k_pci 0000:00:05.0: peer-unmap-event: unknown peer id 24
 ath10k_pci 0000:00:05.0: peer-unmap-event: unknown peer id 8
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

A bit of general cleanup to make debug messages more useful.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

In case firmware fails to start the scan, then complete
the start condition and clean up so that driver does not
block on timeout.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This should fix a very rare occurrence of the following deadlock:

  [<ffffffffa018265e>] ath10k_wmi_tx_beacons_nowait+0x1e/0x50 [ath10k_core]
  [<ffffffffa01829b6>] ath10k_wmi_op_ep_tx_credits+0x16/0x40 [ath10k_core]
  [<ffffffffa017d685>] ath10k_htc_send+0x285/0x3d0 [ath10k_core]
  [<ffffffffa0184b81>] ath10k_wmi_cmd_send_nowait+0x81/0x110 [ath10k_core]
  [<ffffffffa0184c61>] ath10k_wmi_tx_beacon_nowait.part.33+0x51/0x90 [ath10k_core]
  [<ffffffffa0184cd0>] ath10k_wmi_tx_beacons_iter+0x30/0x40 [ath10k_core]
  [<ffffffff81882246>] __iterate_active_interfaces+0xa6/0x100
  [<ffffffffa0184ca0>] ? ath10k_wmi_tx_beacon_nowait.part.33+0x90/0x90 [ath10k_core]
  [<ffffffff818822ae>] ieee80211_iterate_active_interfaces_atomic+0xe/0x10
  [<ffffffffa0182676>] ath10k_wmi_tx_beacons_nowait+0x36/0x50 [ath10k_core]
  [<ffffffffa01829b6>] ath10k_wmi_op_ep_tx_credits+0x16/0x40 [ath10k_core]
  [<ffffffffa017d140>] ath10k_htc_rx+0x280/0x410 [ath10k_core]
  [<ffffffffa01bcbf0>] ? ath10k_ce_completed_recv_next+0x60/0x80 [ath10k_pci]
  [<ffffffffa01bc6ab>] ath10k_pci_ce_recv_data+0x11b/0x1d0 [ath10k_pci]
  [<ffffffffa01bcf44>] ath10k_ce_per_engine_service+0x64/0xc0 [ath10k_pci]
  [<ffffffffa01bcfc2>] ath10k_ce_per_engine_service_any+0x22/0x50 [ath10k_pci]
  [<ffffffffa01bc4d0>] ath10k_pci_tasklet+0x30/0x90 [ath10k_pci]
  [<ffffffff81055a55>] tasklet_action+0xc5/0x100

To prevent this make sure to release ar->data_lock
while calling to ath10k_wmi_beacon_send_ref_nowait().
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Ath10k driver sets wrong default key idx that results in
sending unicast frames with multicast key.

The reason for this behavior is that cached broadcast key
is installed for station MAC address on association. After
dot1x completes, unicast key is installed for station
MAC address. Default key idx is set to broadcast key id when
driver tries to send broadcast frame. This causes firmware
to use broadcast key id to transmit unicast frames to stations.

Used TX_USAGE flag to set default key for stations.

Added callback for setting unicast default idx which will be
invoked on every default key idx configuration.
Signed-off-by: NSenthilKumar Jegadeesan <sjegadee@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Enable the MCS8 and MCS9 support for 2.4G band, it will
use these data rate with other devices having the same
capability.
Signed-off-by: NYanbo Li <yanbol@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Firmware revisions providing sta keepalive service
have it enabled by default.

mac80211 already does idle connection polling so
it makes no sense to duplicate this in ath10k.
mac80211 wouldn't even know of the offloaded
keepalive NullFunc frames.

This prevents sending out some extraneous frames
on the air.
Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

New wmi-tlv firmware for qca6174 supports this.

This should fix issues related to multi-vif WMM.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>