If already requested, gpio_data and irq should be freed in the case of an
error.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Acked-by: NJonathan Cameron <jic23@cam.ac.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Occasionally it is helpful to be able to turn a temperature sensor off
(for example if it's making unwanted electrical noise).  This patch
adds a sysfs node to put any adm1021 compatible device into low power mode.
Signed-off-by: NMichael Abbott <michael.abbott@diamond.ac.uk>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The ADM1023 temperature sensor supports higher resolution for its external
sensor (sensitivity of 1/8 deg C).  This patch makes this higher
resolution available through the appropriate temperature sysfs nodes.

Curiously, this functionality was available in the 2.4 kernel driver (but
formatted in a less helpful manner).

Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: NMichael Abbott <michael.abbott@diamond.ac.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Acked-by: NPavel Machek <pavel@ucw.cz>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This enabled power management functions for the SPI transport layer of the
lis3 devices.  The device's suspend mode is only entered in case no wakeup
threshold has been given.  In this case, the device is supposed to wake up
the system and must thus not be put to deep sleep.

[randy.dunlap@oracle.com: fix lis3-spi for CONFIG_PM=n]
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Acked-by: NPavel Machek <pavel@ucw.cz>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This offers a way for platforms to define flags and thresholds for the
free-fall/wakeup functions of the lis302d chips.

More registers needed to be seperated as they are specific to the
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Acked-by: NPavel Machek <pavel@ucw.cz>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Bit 0x80 in CTRL_REG3 is an ACTIVE_LOW rather than an ACTIVE_HIGH
function, I got that wrong during my last change.
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Acked-by: NPavel Machek <pavel@ucw.cz>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Enable the coretemp driver on an Intel Atom.

I'm not sure if the readings are correct, however - on my 330, the driver
reports values between 27 and 41 °C (with core1 being about 8°C hotter
than core0, given the same load).  Maybe the maximum temperature of 100 °C
is wrong for Atom CPUs.

Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add checks for Blackfin-specific issues that seem to crop up from time to
time.  In particular, we have helper macros to break a 32bit address into
the hi/lo parts, and we want to make sure people use the csync/ssync
variant that includes fun anomaly workarounds.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NAndy Whitcroft <apw@canonical.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Limit our type matcher to the s/u/le/be etc sizes that actually exist to
prevent miss categorising s2 as a type.  Fix up the spelling of the error
also.
Signed-off-by: NAndy Whitcroft <apw@canonical.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

We should not recommend braces for the following:

    #define pr_fmt(fmt)    "%s: " fmt, __func__

allow things with double quotes round them to avoid this check.
Signed-off-by: NAndy Whitcroft <apw@canonical.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Impact:
  - More verbose help/usage message.
  - Make the option -f an alias for --file.
  - On -h, --help, and --version display help message and exit(0).
  - With no FILE(s) given, exit(1) with "no input files".
  - On invalid options display help/usage and exit(1).

Based on a patch by Pavel Machek.
Signed-off-by: NHannes Eder <hannes@hanneseder.net>
Acked-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NAndy Whitcroft <apw@canonical.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Ensure we terminate when there are no futher continuation lines when
trying to determine relative indent of conditionals and their blocks.
Reported-by: NJohn Daiker <daikerjohn@gmail.com>
Signed-off-by: NAndy Whitcroft <apw@canonical.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This fixes the sanitation process in checkpatch.pl so that it blocks out
the text after a C99 style comment the same way it does with block style
comments.  This prevents the text from getting processed as regular code.
Signed-off-by: NDaniel Walker <dwalker@fifo99.com>
Signed-off-by: NAndy Whitcroft <apw@canonical.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

An else cannot start a type, it would have to be within a block after the
else.  This can trigger false modifier matching.
Signed-off-by: NAndy Whitcroft <apw@canonical.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add kerneldoc annotations for function formals of type struct flex_array
and gfp_t which are currently lacking.
Signed-off-by: NDavid Rientjes <rientjes@google.com>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

FLEX_ARRAY_INIT(element_size, total_nr_elements) cannot determine if
either parameter is valid, so flex arrays which are statically allocated
with this interface can easily become corrupted or reference beyond its
allocated memory.

This removes FLEX_ARRAY_INIT() as a struct flex_array initializer since no
initializer may perform the required checking.  Instead, the array is now
defined with a new interface:

	DEFINE_FLEX_ARRAY(name, element_size, total_nr_elements)

This may be prefixed with `static' for file scope.

This interface includes compile-time checking of the parameters to ensure
they are valid.  Since the validity of both element_size and
total_nr_elements depend on FLEX_ARRAY_BASE_SIZE and FLEX_ARRAY_PART_SIZE,
the kernel build will fail if either of these predefined values changes
such that the array parameters are no longer valid.

Since BUILD_BUG_ON() requires compile time constants, several of the
static inline functions that were once local to lib/flex_array.c had to be
moved to include/linux/flex_array.h.
Signed-off-by: NDavid Rientjes <rientjes@google.com>
Acked-by: NDave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add a new function to the flex_array API:

	int flex_array_shrink(struct flex_array *fa)

This function will free all unused second-level pages.  Since elements are
now poisoned if they are not allocated with __GFP_ZERO, it's possible to
identify parts that consist solely of unused elements.

flex_array_shrink() returns the number of pages freed.
Signed-off-by: NDavid Rientjes <rientjes@google.com>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Newly initialized flex_array's and/or flex_array_part's are now poisoned
with a new poison value, FLEX_ARRAY_FREE.  It's value is similar to
POISON_FREE used in the various slab allocators, but is different to
distinguish between flex array's poisoned kmem and slab allocator poisoned
kmem.

This will allow us to identify flex_array_part's that only contain free
elements (and free them with an addition to the flex_array API).  This
could also be extended in the future to identify `get' uses on elements
that have not been `put'.

If __GFP_ZERO is passed for a part's gfp mask, the poisoning is avoided.
These elements are considered to be in-use since they have been
initialized.
Signed-off-by: NDavid Rientjes <rientjes@google.com>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add a new function to the flex_array API:

	int flex_array_clear(struct flex_array *fa,
				unsigned int element_nr)

This function will zero the element at element_nr in the flex_array.

Although this is equivalent to using flex_array_put() and passing a
pointer to zero'd memory, flex_array_clear() does not require such a
pointer to memory that would most likely need to be allocated on the
caller's stack which could be significantly large depending on
element_size.
Signed-off-by: NDavid Rientjes <rientjes@google.com>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NMarcin Slusarz <marcin.slusarz@gmail.com>
Reviewed-by: NFrederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NJoe Perches <joe@perches.com>
Cc: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

A couple of new uses of separate "P: name" "M: address" lines are
converted to single line "M: name <address>"
Signed-off-by: NJoe Perches <joe@perches.com>
Cc: Anil Ravindranath <anil_ravindranath@pmc-sierra.com>
Cc: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Otherwise 'arch/arm/*omap*/foo.c' wouldn't match
Signed-off-by: NFelipe Contreras <felipe.contreras@gmail.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NFelipe Contreras <felipe.contreras@gmail.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Previous behavior was "bottom-up" in each section from the pattern "F:"
entry that matched.  Now information is entered into the various lists in
the "as entered" order for each matched section.

This also allows the F: entry to be put anywhere in a section, not just as
the last entries in the section.

And a couple of improvements:

Don't alphabetically sort before outputting the matched scm, status,
subsystem and web sections.

Ignore content after a single email address so these entries are acceptable
M:	name <address> whatever other comment

And a fix:

Make an M: entry without a name again use the name from an immediately
preceding P: line if it exists.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Allow control over the elimination of duplicate email names and addresses

--remove-duplicates will use the first email name or address presented
--noremove-duplicates will emit all names and addresses

--remove-duplicates is enabled by default

For instance:

$ ./scripts/get_maintainer.pl -f drivers/char/tty_ioctl.c
Greg Kroah-Hartman <gregkh@suse.de>
Alan Cox <alan@linux.intel.com>
Mike Frysinger <vapier@gentoo.org>
Alexey Dobriyan <adobriyan@gmail.com>
linux-kernel@vger.kernel.org

$ ./scripts/get_maintainer.pl -f --noremove-duplicates drivers/char/tty_ioctl.c
Greg Kroah-Hartman <gregkh@suse.de>
Alan Cox <alan@redhat.com>
Alan Cox <alan@linux.intel.com>
Alan Cox <alan@lxorguk.ukuu.org.uk>
Mike Frysinger <vapier@gentoo.org>
Alexey Dobriyan <adobriyan@gmail.com>
linux-kernel@vger.kernel.org

Using --remove-duplicates could eliminate multiple maintainers that
share the same name but not the same email address.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If a person sets a separator, it's only used if --nomultiline is set.
Don't make the command line also include --nomultiline in that case.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add reading and using .mailmap file if it exists
Convert address entries in .mailmap to first encountered address
Don't terminate shell commands with \n
Strip characters found after sign-offs by: name <address> [stripped]
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Added format_email and parse_email routines to reduce inline use.

Added email_address_inuse to eliminate multiple maintainer entries
for the same email address, the first name encountered is used.

Used internal perl equivalents of shell cmd use of grep|cut|sort|uniq
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

--pattern-depth is used to control how many levels of directory traversal
should be performed to find maintainers.  default is 0 (all directory levels).

For instance:

MAINTAINERS currently has multiple M: and F: entries that match
net/netfilter/ipvs/ip_vs_app.c

IPVS
M:	Wensong Zhang <wensong@linux-vs.org>
M:	Simon Horman <horms@verge.net.au>
M:	Julian Anastasov <ja@ssi.bg>
[...]
F:	net/netfilter/ipvs/

NETFILTER/IPTABLES/IPCHAINS
[...]
M:	Patrick McHardy <kaber@trash.net>
[...]
F:	net/netfilter/

NETWORKING [GENERAL]
M:	"David S. Miller" <davem@davemloft.net>
[...]
F:	net/

THE REST
M:	Linus Torvalds <torvalds@linux-foundation.org>
[...]
F:	*/

Using this command will return all of those maintainers:
(except Linus unless --git-chief-maintainers is specified)

$ ./scripts/get_maintainer.pl --nogit -nol \
	-f net/netfilter/ipvs/ip_vs_app.c
Julian Anastasov <ja@ssi.bg>
Simon Horman <horms@verge.net.au>
Wensong Zhang <wensong@linux-vs.org>
Patrick McHardy <kaber@trash.net>
David S. Miller <davem@davemloft.net>

Adding --pattern-depth=1 will match at the deepest level
$ ./scripts/get_maintainer.pl --nogit -nol --pattern-depth=1 \
	-f net/netfilter/ipvs/ip_vs_app.c
Julian Anastasov <ja@ssi.bg>
Simon Horman <horms@verge.net.au>
Wensong Zhang <wensong@linux-vs.org>

Adding --pattern-depth=2 will match at the deepest level and 1 higher
$ ./scripts/get_maintainer.pl --nogit -nol --pattern-depth=2 \
	-f net/netfilter/ipvs/ip_vs_app.c
Julian Anastasov <ja@ssi.bg>
Simon Horman <horms@verge.net.au>
Wensong Zhang <wensong@linux-vs.org>
Patrick McHardy <kaber@trash.net>

and so on.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Before this change, matched sections were added in the order
of appearance in the normally alphabetic section order of
the MAINTAINERS file.

For instance, finding the maintainer for drivers/scsi/wd7000.c
would first find "SCSI SUBSYSTEM", then "WD7000 SCSI SUBSYSTEM",
then "THE REST".

before patch:

$ ./scripts/get_maintainer.pl --nogit -f drivers/scsi/wd7000.c
James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
Miroslav Zagorac <zaga@fly.cc.fer.hr>
linux-scsi@vger.kernel.org
linux-kernel@vger.kernel.org

get_maintainer.pl now selects matched sections by longest pattern match.
Longest is the number of "/"s and any specific file pattern.

This changes the example output order of MAINTAINERS to whatever is
selected in "WD7000 SUBSYSTEM", then "SCSI SYSTEM", then "THE REST".

after patch:

$ ./scripts/get_maintainer.pl --nogit -f drivers/scsi/wd7000.c
Miroslav Zagorac <zaga@fly.cc.fer.hr>
James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
linux-scsi@vger.kernel.org
linux-kernel@vger.kernel.org
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Julia Lawall suggested that get_maintainers.pl should have the
ability to include signatories of commits that are modified by
a particular patch.

Vegard Nossum did something similar once.
http://lkml.org/lkml/2008/5/29/449

The modified script looks the commits for all lines in the
patch, and includes the "-by:" signatories for those commits.
It uses the same git-min-percent, git-max-maintainers, and
git-min-signatures options.  git-since is ignored.

It can be used independently from the --git default, so
        ./scripts/get_maintainers.pl --nogit --git-blame <patch>
or
        ./scripts/get_maintainers.pl --nogit --git-blame -f <file>
is acceptable.

If used with -f <file>, all lines/commits for the file are
checked.

--git-blame can be slow if used with -f <file>
--git-blame does not work with -f <directory>
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NHannes Eder <heder@google.com>
Cc: Joe Perches <joe@perches.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If pmd_alloc() fails we should only free the prior allocated pud, if
pte_alloc_map() fails, we should free pmd as well.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NChristoph Hellwig <hch@lst.de>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Move the state residency accounting and statistics computation off the hot
exit path.

On exit, the need to recompute statistics is recorded, and new statistics
will be computed when menu_select is called again.

The expected effect is to reduce processor wakeup latency from sleep
(C-states).  We are speaking of few hundreds of cycles reduction out of a
several microseconds latency (determined by the hardware transition), so
it is difficult to measure.
Signed-off-by: NCorrado Zoccolo <czoccolo@gmail.com>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Adam Belay <abelay@novell.com
Acked-by: NArjan van de Ven <arjan@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix the menu idle governor which balances power savings, energy efficiency
and performance impact.

The reason for a reworked governor is that there have been serious
performance issues reported with the existing code on Nehalem server
systems.

To show this I'm sure Andrew wants to see benchmark results:
(benchmark is "fio", "no cstates" is using "idle=poll")

		no cstates	current linux	new algorithm
1 disk		107 Mb/s	85 Mb/s		105 Mb/s
2 disks		215 Mb/s	123 Mb/s	209 Mb/s
12 disks	590 Mb/s	320 Mb/s	585 Mb/s

In various power benchmark measurements, no degredation was found by our
measurement&diagnostics team.  Obviously a small percentage more power was
used in the "fio" benchmark, due to the much higher performance.

While it would be a novel idea to describe the new algorithm in this
commit message, I cheaped out and described it in comments in the code
instead.

[changes since first post: spelling fixes from akpm, review feedback,
folded menu-tng into menu.c]
Signed-off-by: NArjan van de Ven <arjan@linux.intel.com>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Yanmin Zhang <yanmin_zhang@linux.intel.com>
Acked-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NChristoph Hellwig <hch@lst.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>