- 30 3月, 2006 1 次提交
-
-
由 Denis Vlasenko 提交于
On a allyesconfig'ured kernel: Size Uses Wasted Name and definition ===== ==== ====== ================================================ 95 162 12075 netif_wake_queue include/linux/netdevice.h 129 86 9265 dev_kfree_skb_any include/linux/netdevice.h 127 56 5885 netif_device_attach include/linux/netdevice.h 73 86 4505 dev_kfree_skb_irq include/linux/netdevice.h 46 60 1534 netif_device_detach include/linux/netdevice.h 119 16 1485 __netif_rx_schedule include/linux/netdevice.h 143 5 492 netif_rx_schedule include/linux/netdevice.h 81 7 366 netif_schedule include/linux/netdevice.h netif_wake_queue is big because __netif_schedule is a big inline: static inline void __netif_schedule(struct net_device *dev) { if (!test_and_set_bit(__LINK_STATE_SCHED, &dev->state)) { unsigned long flags; struct softnet_data *sd; local_irq_save(flags); sd = &__get_cpu_var(softnet_data); dev->next_sched = sd->output_queue; sd->output_queue = dev; raise_softirq_irqoff(NET_TX_SOFTIRQ); local_irq_restore(flags); } } static inline void netif_wake_queue(struct net_device *dev) { #ifdef CONFIG_NETPOLL_TRAP if (netpoll_trap()) return; #endif if (test_and_clear_bit(__LINK_STATE_XOFF, &dev->state)) __netif_schedule(dev); } By de-inlining __netif_schedule we are saving a lot of text at each callsite of netif_wake_queue and netif_schedule. __netif_rx_schedule is also big, and it makes more sense to keep both of them out of line. Patch also deinlines dev_kfree_skb_any. We can deinline dev_kfree_skb_irq instead... oh well. netif_device_attach/detach are not hot paths, we can deinline them too. Signed-off-by: NDenis Vlasenko <vda@ilport.com.ua> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 21 3月, 2006 2 次提交
-
-
由 Stephen Hemminger 提交于
Get rid of the old __dev_put macro that is just a hold over from pre 2.6 kernel. And turn dev_hold into an inline instead of a macro. Signed-off-by: NStephen Hemminger <shemminger@osdl.org> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Stefan Rompf 提交于
this patch adds a dormant flag to network devices, RFC2863 operstate derived from these flags and possibility for userspace interaction. It allows drivers to signal that a device is unusable for user traffic without disabling queueing (and therefore the possibility for protocol establishment traffic to flow) and a userspace supplicant (WPA, 802.1X) to mark a device unusable without changes to the driver. It is the result of our long discussion. However I must admit that it represents what Jamal and I agreed on with compromises towards Krzysztof, but Thomas and Krzysztof still disagree with some parts. Anyway I think it should be applied. Signed-off-by: NStefan Rompf <stefan@loplof.de> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 01 12月, 2005 1 次提交
-
-
由 shemminger@osdl.org 提交于
I didn't like the name netif_rx_schedule_test(), in earlier patches and changed to __netif_rx_schedule_prep to be more consistent. Signed-off-by: NStephen Hemminger <shemminger@osdl.org> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
- 14 11月, 2005 1 次提交
-
-
由 Mitch Williams 提交于
dev_valid_name() is a useful function. Make it public. Signed-off-by: NMitch Williams <mitch.a.williams@intel.com> Acked-by: NJay Vosburgh <fubar@us.ibm.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 11 11月, 2005 1 次提交
-
-
由 Herbert Xu 提交于
Here is the patch that introduces the generic skb_checksum_complete which also checks for hardware RX checksum faults. If that happens, it'll call netdev_rx_csum_fault which currently prints out a stack trace with the device name. In future it can turn off RX checksum. I've converted every spot under net/ that does RX checksum checks to use skb_checksum_complete or __skb_checksum_complete with the exceptions of: * Those places where checksums are done bit by bit. These will call netdev_rx_csum_fault directly. * The following have not been completely checked/converted: ipmr ip_vs netfilter dccp This patch is based on patches and suggestions from Stephen Hemminger and David S. Miller. Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 29 10月, 2005 1 次提交
-
-
由 Ananda Raju 提交于
Attached is kernel patch for UDP Fragmentation Offload (UFO) feature. 1. This patch incorporate the review comments by Jeff Garzik. 2. Renamed USO as UFO (UDP Fragmentation Offload) 3. udp sendfile support with UFO This patches uses scatter-gather feature of skb to generate large UDP datagram. Below is a "how-to" on changes required in network device driver to use the UFO interface. UDP Fragmentation Offload (UFO) Interface: ------------------------------------------- UFO is a feature wherein the Linux kernel network stack will offload the IP fragmentation functionality of large UDP datagram to hardware. This will reduce the overhead of stack in fragmenting the large UDP datagram to MTU sized packets 1) Drivers indicate their capability of UFO using dev->features |= NETIF_F_UFO | NETIF_F_HW_CSUM | NETIF_F_SG NETIF_F_HW_CSUM is required for UFO over ipv6. 2) UFO packet will be submitted for transmission using driver xmit routine. UFO packet will have a non-zero value for "skb_shinfo(skb)->ufo_size" skb_shinfo(skb)->ufo_size will indicate the length of data part in each IP fragment going out of the adapter after IP fragmentation by hardware. skb->data will contain MAC/IP/UDP header and skb_shinfo(skb)->frags[] contains the data payload. The skb->ip_summed will be set to CHECKSUM_HW indicating that hardware has to do checksum calculation. Hardware should compute the UDP checksum of complete datagram and also ip header checksum of each fragmented IP packet. For IPV6 the UFO provides the fragment identification-id in skb_shinfo(skb)->ip6_frag_id. The adapter should use this ID for generating IPv6 fragments. Signed-off-by: NAnanda Raju <ananda.raju@neterion.com> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (forwarded) Signed-off-by: NArnaldo Carvalho de Melo <acme@mandriva.com>
-
- 28 9月, 2005 1 次提交
-
-
由 Eric Dumazet 提交于
Place them on separate cache lines in SMP to lower memory bouncing between multiple CPU accessing the device. - One part is mostly used on receive path (including eth_type_trans()) (poll_list, poll, quota, weight, last_rx, dev_addr, broadcast) - One part is mostly used on queue transmit path (qdisc) (queue_lock, qdisc, qdisc_sleeping, qdisc_list, tx_queue_len) - One part is mostly used on xmit path (device) (xmit_lock, xmit_lock_owner, priv, hard_start_xmit, trans_start) 'features' is placed outside of these hot points, in a location that may be shared by all cpus (because mostly read) name_hlist is moved close to name[IFNAMSIZ] to speedup __dev_get_by_name() Signed-off-by: NEric Dumazet <dada1@cosmosbay.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 16 9月, 2005 1 次提交
-
-
由 Stephen Hemminger 提交于
Here is revised patch against netdev sky2 branch. It includes whitespace fixes, all the changes from the previous review as well as some optimizations and timing fixes to solve some of the hangs. The stall problem is better but not perfect. It appears that under stress the chip can't keep up with the bus and sends a pause frame, then hangs. This version is for testing, and hopefully other eyes might see the root cause of the problem. I don't want to reinvent the ugly watchdog code in the syskonnect version of sk98lin. If you read it you will see, the original driver writer and the hardware developer obviously didn't understand each other. Dual port support is included, but not tested yet. It did require small change to NAPI since both ports share same IRQ. Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
- 14 9月, 2005 1 次提交
-
-
由 Nishanth Aravamudan 提交于
Use schedule_timeout_interruptible() instead of set_current_state()/schedule_timeout() to reduce kernel size. Signed-off-by: NNishanth Aravamudan <nacc@us.ibm.com> Cc: Jeff Garzik <jgarzik@pobox.com> Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
- 30 8月, 2005 4 次提交
-
-
由 Jon Wetzel 提交于
This patch adds a new field to net device to hold the permanent hardware address, and adds a new generic ethtool_op function to get that address. Signed-off-by: NJon Wetzel <jon_wetzel@dell.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Arnaldo Carvalho de Melo 提交于
Of this type, mostly: CHECK net/ipv6/netfilter.c net/ipv6/netfilter.c:96:12: warning: symbol 'ipv6_netfilter_init' was not declared. Should it be static? net/ipv6/netfilter.c:101:6: warning: symbol 'ipv6_netfilter_fini' was not declared. Should it be static? Signed-off-by: NArnaldo Carvalho de Melo <acme@mandriva.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Denis Vlasenko 提交于
# grep -r 'netif_carrier_o[nf]' linux-2.6.12 | wc -l 246 # size vmlinux.org vmlinux.carrier text data bss dec hex filename 4339634 1054414 259296 5653344 564360 vmlinux.org 4337710 1054414 259296 5651420 563bdc vmlinux.carrier And this ain't an allyesconfig kernel! Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Bonding just wants the device before the skb_bond() decapsulation occurs, so simply pass that original device into packet_type->func() as an argument. It remains to be seen whether we can use this same exact thing to get rid of skb->input_dev as well. Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 24 6月, 2005 4 次提交
-
-
由 Stephen Hemminger 提交于
Eliminate the throttling behaviour when the netif receive queue fills because it behaves badly when using high speed networks under load. The throttling cause multiple packet drops that cause TCP to go into slow start mode. The same effective patch has been part of BIC TCP and H-TCP as well as part of Web100. The existing code drops 100's of packets when the queue fills; this changes it to individual packet drop-tail. Signed-off-by: NStephen Hemmminger <shemminger@osdl.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Stephen Hemminger 提交于
Remove the congestion sensing mechanism from netif_rx, and always return either full or empty. Almost no driver checks the return value from netif_rx, and those that do only use it for debug messages. The original design of netif_rx was to do flow control based on the receive queue, but NAPI has supplanted this and no driver uses the feedback. Signed-off-by: NStephen Hemminger <shemminger@osdl.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Stephen Hemminger 提交于
Remove last vestiages of fastroute code that is no longer used. Signed-off-by: NStephen Hemminger <shemminger@osdl.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Paulo Marques 提交于
This patch creates a new kstrdup library function and changes the "local" implementations in several places to use this function. Most of the changes come from the sound and net subsystems. The sound part had already been acknowledged by Takashi Iwai and the net part by David S. Miller. I left UML alone for now because I would need more time to read the code carefully before making changes there. Signed-off-by: NPaulo Marques <pmarques@grupopie.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
- 23 6月, 2005 1 次提交
-
-
由 Jeff Moyer 提交于
This patch introduces a netpoll_info structure, which the struct net_device will now point to instead of pointing to a struct netpoll. The reason for this is two-fold: 1) fields such as the rx_flags, poll_owner, and poll_lock should be maintained per net_device, not per netpoll; and 2) this is a first step in providing support for multiple netpoll clients to register against the same net_device. The struct netpoll is now pointed to by the netpoll_info structure. As such, the previous behaviour of the code is preserved. Signed-off-by: NJeff Moyer <jmoyer@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 03 6月, 2005 1 次提交
-
-
由 Jiri Benc 提交于
When the hardware header size is a multiple of HH_DATA_MOD, HH_DATA_OFF() incorrectly returns HH_DATA_MOD (instead of 0). This affects ieee80211 layer as 802.11 header is 32 bytes long. Signed-off-by: NJiri Benc <jbenc@suse.cz> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 30 5月, 2005 2 次提交
-
-
由 Stephen Hemminger 提交于
The features field in netdevice is really a bitmask, and bitmask's should be unsigned. Signed-off-by: NStephen Hemminger <shemminger@osdl.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Stephen Hemminger 提交于
Resend of earlier patch (no changes) from Catalin used to provide device feature change notification. Signed-off-by: Catalin BOIE <catab at umbrella.ro> Acked-by: NStephen Hemminger <shemminger@osdl.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 24 5月, 2005 1 次提交
-
-
由 Alexey Dobriyan 提交于
Everybody does struct packet_type foo_packet_type = { .type = __constant_htons(ETH_P_FOO); }; 5 introduced warnings will be properly fixed later. Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 06 5月, 2005 1 次提交
-
-
由 Jesper Juhl 提交于
Ross moved. Remove the bad email address so people will find the correct one in ./CREDITS. Signed-off-by: NJesper Juhl <juhl-lkml@dif.dk> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
- 17 4月, 2005 1 次提交
-
-
由 Linus Torvalds 提交于
Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
-