Jouni reported that certain combinations of hwsim test cases failed,
and we found that beaconing was erroneously enabled too early on any
channel switch, which lead to the BI of 2000 TU from the first test
case to leak into the second one, which then didn't beacon properly.

To fix this, set data->beacon_int to zero when all stop beaconing so
that beaconing cannot be started (which was intended as 'restarted')
elsewhere.

Additionally, Jouni found that due to this 'restart' and the beacon
interval handling station interfaces would also have a needlessly
running beacon timer all the time, of course not doing anything.

To also fix the latter case only use the beacon interval when it's
actually needed, i.e. when beaconing gets enabled.
Reported-by: NJouni Malinen <j@w1.fi>
Tested-by: NJouni Malinen <j@w1.fi>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This allows wpa_supplicant/hostapd to send a vendor command and verify
response to that command and a vendor event.
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Due to the checks in get_hwsim_data_ref_from_addr, wmediumd
was only able to use the second mac address (those starting with
0x42).  This is confusing and needlessly limiting, so allow any
configured address.
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Contrary to common expectations for an "int" return, these functions
return only a positive value -- if used correctly they cannot even
return 0 because the message header will necessarily be in the skb.

This makes the very common pattern of

  if (genlmsg_end(...) < 0) { ... }

be a whole bunch of dead code. Many places also simply do

  return nlmsg_end(...);

and the caller is expected to deal with it.

This also commonly (at least for me) causes errors, because it is very
common to write

  if (my_function(...))
    /* error condition */

and if my_function() does "return nlmsg_end()" this is of course wrong.

Additionally, there's not a single place in the kernel that actually
needs the message length returned, and if anyone needs it later then
it'll be very easy to just use skb->len there.

Remove this, and make the functions void. This removes a bunch of dead
code as described above. The patch adds lines because I did

-	return nlmsg_end(...);
+	nlmsg_end(...);
+	return 0;

I could have preserved all the function's return values by returning
skb->len, but instead I've audited all the places calling the affected
functions and found that none cared. A few places actually compared
the return value with <= 0 in dump functionality, but that could just
be changed to < 0 with no change in behaviour, so I opted for the more
efficient version.

One instance of the error I've made numerous times now is also present
in net/phonet/pn_netlink.c in the route_dumpit() function - it didn't
check for <0 or <=0 and thus broke out of the loop every single time.
I've preserved this since it will (I think) have caused the messages to
userspace to be formatted differently with just a single message for
every SKB returned to userspace. It's possible that this isn't needed
for the tools that actually use this, but I don't even know what they
are so couldn't test that changing this behaviour would be acceptable.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The functions called within the iterators must be called with
tasklets disabled, so use atomic iteration like the rest of
the code and disable tasklets around the whole operation.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

David Binderman reports that the conditions in the first loop
are the wrong way around - checking the array contents before
the size.

Instead of leaving the empty loop there and reordering the two
checks unify it into a single loop that skips over non-matches
and exits after the first match.
Reported-by: NDavid Binderman <dcb314@hotmail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This reverts commit c17aa52c.

It was wrong, IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160_80PLUS80MHZ
already implies that 160 MHz is supported, as it isn't a bitmap
but rather a value in a 2-bit field.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

A properly set alpha2 value consists of two chars that both contain
letters or digits. If no value is set, both chars keep their initial
value zero. Therefore do not send the alpha2 parameter to user space
if either of the characters has been left at its initial zero value.
Signed-off-by: NPatrik Flykt <patrik.flykt@linux.intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

HWSIM_CMD_GET_RADIO returns information about a specific radio id or
all of them in response to a dump. Create the netlink skb or use the
one provided by the dump functionality. Use the existing attribute
appending function to fill in the same attributes when creating a
new hwsim radio.

Save alpha2 and struct ieee80211_regdomain in the hwsim data or else
they will be lost in the depths of regulatory infrastructure.
Signed-off-by: NPatrik Flykt <patrik.flykt@linux.intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Factor out netlink message attribute appending in order to reuse it
with later code. As a result move netlink skb allocation to the
calling function.
Signed-off-by: NPatrik Flykt <patrik.flykt@linux.intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The hwname will always be set if idx is negative (as it's
a u32 read into an s64 it can't overflow either) so we can
remove the unnecessary check for hwname being non-NULL.

This was reported by smatch.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

We can always know the hwname of the radio so use the value
from wiphy.
Signed-off-by: NJukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This adds support for scanning with random MAC address for
both software and hardware scan.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Allow drivers to support NL80211_SCAN_FLAG_RANDOM_ADDR with software
based scanning and generate a random MAC address for them for every
scan request with the flag.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Radiotap vendor namespace data might still be useful, but we
reverted it because it used too much space in the RX status.
Put it back, but address the space problem by using a single
bit only and putting everything else into the skb->data.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When deleting old radio via HWSIM_CMD_DEL_RADIO then listeners on the
multicast group "config" are informed.
Signed-off-by: NJukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When adding new radio via HWSIM_CMD_NEW_RADIO then listeners on the
multicast group "config" are informed.

While at it, refactor the configuration parameters to be able to
pass them directly and have fewer function arguments.
Signed-off-by: NJukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

A few recent additions to the netlink attributes neglected
to add policy entries, fix that now.
Reported-by: NJukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This newline shouldn't be there, remove it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This lets hostapd start if you have SGI-20 configured
as one of your HT capabilities.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add frequency attribute when sending to user-space over
netlink socket.  The frequency is currently ignored when
receiving from user-space.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The driver is not released when ieee80211_register_hw fails in
mac80211_hwsim_create_radio, leading to the access to the unregistered (and
possibly freed) device in platform_driver_unregister:

[    0.447547] mac80211_hwsim: ieee80211_register_hw failed (-2)
[    0.448292] ------------[ cut here ]------------
[    0.448854] WARNING: CPU: 0 PID: 1 at ../include/linux/kref.h:47 kobject_get+0x33/0x50()
[    0.449839] CPU: 0 PID: 1 Comm: swapper Not tainted 3.17.0-00001-gdd46990-dirty #2
[    0.450813] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
[    0.451512]  00000000 00000000 78025e38 7967c6c6 78025e68 7905e09b 7988b480 00000000
[    0.452579]  00000001 79887d62 0000002f 79170bb3 79170bb3 78397008 79ac9d74 00000001
[    0.453614]  78025e78 7905e15d 00000009 00000000 78025e84 79170bb3 78397000 78025e8c
[    0.454632] Call Trace:
[    0.454921]  [<7967c6c6>] dump_stack+0x16/0x18
[    0.455453]  [<7905e09b>] warn_slowpath_common+0x6b/0x90
[    0.456067]  [<79170bb3>] ? kobject_get+0x33/0x50
[    0.456612]  [<79170bb3>] ? kobject_get+0x33/0x50
[    0.457155]  [<7905e15d>] warn_slowpath_null+0x1d/0x20
[    0.457748]  [<79170bb3>] kobject_get+0x33/0x50
[    0.458274]  [<7925824f>] get_device+0xf/0x20
[    0.458779]  [<7925b5cd>] driver_detach+0x3d/0xa0
[    0.459331]  [<7925a3ff>] bus_remove_driver+0x8f/0xb0
[    0.459927]  [<7925bf80>] ? class_unregister+0x40/0x80
[    0.460660]  [<7925bad7>] driver_unregister+0x47/0x50
[    0.461248]  [<7925c033>] ? class_destroy+0x13/0x20
[    0.461824]  [<7925d07b>] platform_driver_unregister+0xb/0x10
[    0.462507]  [<79b51ba0>] init_mac80211_hwsim+0x3e8/0x3f9
[    0.463161]  [<79b30c58>] do_one_initcall+0x106/0x1a9
[    0.463758]  [<79b517b8>] ? if_spi_init_module+0xac/0xac
[    0.464393]  [<79b517b8>] ? if_spi_init_module+0xac/0xac
[    0.465001]  [<79071935>] ? parse_args+0x2f5/0x480
[    0.465569]  [<7906b41e>] ? __usermodehelper_set_disable_depth+0x3e/0x50
[    0.466345]  [<79b30dd9>] kernel_init_freeable+0xde/0x17d
[    0.466972]  [<79b304d6>] ? do_early_param+0x7a/0x7a
[    0.467546]  [<79677b1b>] kernel_init+0xb/0xe0
[    0.468072]  [<79075f42>] ? schedule_tail+0x12/0x40
[    0.468658]  [<79686580>] ret_from_kernel_thread+0x20/0x30
[    0.469303]  [<79677b10>] ? rest_init+0xc0/0xc0
[    0.469829] ---[ end trace ad8ac403ff8aef5c ]---
[    0.470509] ------------[ cut here ]------------
[    0.471047] WARNING: CPU: 0 PID: 1 at ../kernel/locking/lockdep.c:3161 __lock_acquire.isra.22+0x7aa/0xb00()
[    0.472163] DEBUG_LOCKS_WARN_ON(id >= MAX_LOCKDEP_KEYS)
[    0.472774] CPU: 0 PID: 1 Comm: swapper Tainted: G        W      3.17.0-00001-gdd46990-dirty #2
[    0.473815] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
[    0.474492]  78025de0 78025de0 78025da0 7967c6c6 78025dd0 7905e09b 79888931 78025dfc
[    0.475515]  00000001 79888a93 00000c59 7907f33a 7907f33a 78028000 fffe9d09 00000000
[    0.476519]  78025de8 7905e10e 00000009 78025de0 79888931 78025dfc 78025e24 7907f33a
[    0.477523] Call Trace:
[    0.477821]  [<7967c6c6>] dump_stack+0x16/0x18
[    0.478352]  [<7905e09b>] warn_slowpath_common+0x6b/0x90
[    0.478976]  [<7907f33a>] ? __lock_acquire.isra.22+0x7aa/0xb00
[    0.479658]  [<7907f33a>] ? __lock_acquire.isra.22+0x7aa/0xb00
[    0.480417]  [<7905e10e>] warn_slowpath_fmt+0x2e/0x30
[    0.480479]  [<7907f33a>] __lock_acquire.isra.22+0x7aa/0xb00
[    0.480479]  [<79078aa5>] ? sched_clock_cpu+0xb5/0xf0
[    0.480479]  [<7907fd06>] lock_acquire+0x56/0x70
[    0.480479]  [<7925b5e8>] ? driver_detach+0x58/0xa0
[    0.480479]  [<79682d11>] mutex_lock_nested+0x61/0x2a0
[    0.480479]  [<7925b5e8>] ? driver_detach+0x58/0xa0
[    0.480479]  [<7925b5e8>] ? driver_detach+0x58/0xa0
[    0.480479]  [<7925b5e8>] driver_detach+0x58/0xa0
[    0.480479]  [<7925a3ff>] bus_remove_driver+0x8f/0xb0
[    0.480479]  [<7925bf80>] ? class_unregister+0x40/0x80
[    0.480479]  [<7925bad7>] driver_unregister+0x47/0x50
[    0.480479]  [<7925c033>] ? class_destroy+0x13/0x20
[    0.480479]  [<7925d07b>] platform_driver_unregister+0xb/0x10
[    0.480479]  [<79b51ba0>] init_mac80211_hwsim+0x3e8/0x3f9
[    0.480479]  [<79b30c58>] do_one_initcall+0x106/0x1a9
[    0.480479]  [<79b517b8>] ? if_spi_init_module+0xac/0xac
[    0.480479]  [<79b517b8>] ? if_spi_init_module+0xac/0xac
[    0.480479]  [<79071935>] ? parse_args+0x2f5/0x480
[    0.480479]  [<7906b41e>] ? __usermodehelper_set_disable_depth+0x3e/0x50
[    0.480479]  [<79b30dd9>] kernel_init_freeable+0xde/0x17d
[    0.480479]  [<79b304d6>] ? do_early_param+0x7a/0x7a
[    0.480479]  [<79677b1b>] kernel_init+0xb/0xe0
[    0.480479]  [<79075f42>] ? schedule_tail+0x12/0x40
[    0.480479]  [<79686580>] ret_from_kernel_thread+0x20/0x30
[    0.480479]  [<79677b10>] ? rest_init+0xc0/0xc0
[    0.480479] ---[ end trace ad8ac403ff8aef5d ]---
[    0.495478] BUG: unable to handle kernel paging request at 00200200
[    0.496257] IP: [<79682de5>] mutex_lock_nested+0x135/0x2a0
[    0.496923] *pde = 00000000
[    0.497290] Oops: 0002 [#1]
[    0.497653] CPU: 0 PID: 1 Comm: swapper Tainted: G        W      3.17.0-00001-gdd46990-dirty #2
[    0.498659] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
[    0.499321] task: 78028000 ti: 78024000 task.ti: 78024000
[    0.499955] EIP: 0060:[<79682de5>] EFLAGS: 00010097 CPU: 0
[    0.500620] EIP is at mutex_lock_nested+0x135/0x2a0
[    0.501145] EAX: 00200200 EBX: 78397434 ECX: 78397460 EDX: 78025e70
[    0.501816] ESI: 00000246 EDI: 78028000 EBP: 78025e8c ESP: 78025e54
[    0.502497]  DS: 007b ES: 007b FS: 0000 GS: 0000 SS: 0068
[    0.503076] CR0: 8005003b CR2: 00200200 CR3: 01b9d000 CR4: 00000690
[    0.503773] Stack:
[    0.503998]  00000000 00000001 00000000 7925b5e8 78397460 7925b5e8 78397474 78397460
[    0.504944]  00200200 11111111 78025e70 78397000 79ac9d74 00000001 78025ea0 7925b5e8
[    0.505451]  79ac9d74 fffffffe 00000001 78025ebc 7925a3ff 7a251398 78025ec8 7925bf80
[    0.505451] Call Trace:
[    0.505451]  [<7925b5e8>] ? driver_detach+0x58/0xa0
[    0.505451]  [<7925b5e8>] ? driver_detach+0x58/0xa0
[    0.505451]  [<7925b5e8>] driver_detach+0x58/0xa0
[    0.505451]  [<7925a3ff>] bus_remove_driver+0x8f/0xb0
[    0.505451]  [<7925bf80>] ? class_unregister+0x40/0x80
[    0.505451]  [<7925bad7>] driver_unregister+0x47/0x50
[    0.505451]  [<7925c033>] ? class_destroy+0x13/0x20
[    0.505451]  [<7925d07b>] platform_driver_unregister+0xb/0x10
[    0.505451]  [<79b51ba0>] init_mac80211_hwsim+0x3e8/0x3f9
[    0.505451]  [<79b30c58>] do_one_initcall+0x106/0x1a9
[    0.505451]  [<79b517b8>] ? if_spi_init_module+0xac/0xac
[    0.505451]  [<79b517b8>] ? if_spi_init_module+0xac/0xac
[    0.505451]  [<79071935>] ? parse_args+0x2f5/0x480
[    0.505451]  [<7906b41e>] ? __usermodehelper_set_disable_depth+0x3e/0x50
[    0.505451]  [<79b30dd9>] kernel_init_freeable+0xde/0x17d
[    0.505451]  [<79b304d6>] ? do_early_param+0x7a/0x7a
[    0.505451]  [<79677b1b>] kernel_init+0xb/0xe0
[    0.505451]  [<79075f42>] ? schedule_tail+0x12/0x40
[    0.505451]  [<79686580>] ret_from_kernel_thread+0x20/0x30
[    0.505451]  [<79677b10>] ? rest_init+0xc0/0xc0
[    0.505451] Code: 89 d8 e8 cf 9b 9f ff 8b 4f 04 8d 55 e4 89 d8 e8 72 9d 9f ff 8d 43 2c 89 c1 89 45 d8 8b 43 30 8d 55 e4 89 53 30 89 4d e4 89 45 e8 <89> 10 8b 55 dc 8b 45 e0 89 7d ec e8 db af 9f ff eb 11 90 31 c0
[    0.505451] EIP: [<79682de5>] mutex_lock_nested+0x135/0x2a0 SS:ESP 0068:78025e54
[    0.505451] CR2: 0000000000200200
[    0.505451] ---[ end trace ad8ac403ff8aef5e ]---
[    0.505451] Kernel panic - not syncing: Fatal exception

Fixes: 9ea92774 ("mac80211_hwsim: Register and bind to driver")
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NJunjie Mao <eternal.n08@gmail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Good for automated testing, where user can create wlan
interfaces with specified names.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Otherwise, it can be very difficult to know which is which
if you are trying to do detailed testing.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

It is not always convenient to have to know the device-id,
so allow deleting by name as well.
Signed-off-by: NBen Greear <greearb@candelatech.com>
[use wiphy_name() instead of dev_name()]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This gives a view into packet activity at the virtual radio
level.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

A platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Add support for new attribute HWSIM_ATTR_DESTROY_RADIO_ON_CLOSE
which can be set by the user space component. The attribute
will cause the kernel to destroy all those radios that were
created by a process if that process dies. The old behaviour
i.e., radios are persistent is still the default.
Signed-off-by: NJukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Trivial cleanups.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

If the packet can't be delivered to userspace (at all or
quickly enough) then it can leak - fix that.
Signed-off-by: NBen Greear <greearb@candelatech.com>
[rewrite commit message]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Use the new static_smps / dynamic_smps feature bits
instead of mac80211-internal hw flags.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The dividend in do_div() is expected to be an unsigned 64-bit integer,
which leads to the following warning when building for 32-bit MIPS:

  drivers/net/wireless/mac80211_hwsim.c: In function 'mac80211_hwsim_set_tsf':
  drivers/net/wireless/mac80211_hwsim.c:664:98: warning: comparison of distinct pointer types lacks a cast [enabled by default]
    data->bcn_delta = do_div(delta, bcn_int);

Since we care about the signedness of delta when adjusting tsf_offset
and bcm_delta, use the absolute value for the division and compare
the two timestamps to determine the sign.
Signed-off-by: NAndrew Bresticker <abrestic@chromium.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Extend alloc_netdev{,_mq{,s}}() to take name_assign_type as argument, and convert
all users to pass NET_NAME_UNKNOWN.

Coccinelle patch:

@@
expression sizeof_priv, name, setup, txqs, rxqs, count;
@@

(
-alloc_netdev_mqs(sizeof_priv, name, setup, txqs, rxqs)
+alloc_netdev_mqs(sizeof_priv, name, NET_NAME_UNKNOWN, setup, txqs, rxqs)
|
-alloc_netdev_mq(sizeof_priv, name, setup, count)
+alloc_netdev_mq(sizeof_priv, name, NET_NAME_UNKNOWN, setup, count)
|
-alloc_netdev(sizeof_priv, name, setup)
+alloc_netdev(sizeof_priv, name, NET_NAME_UNKNOWN, setup)
)

v9: move comments here from the wrong commit
Signed-off-by: NTom Gundersen <teg@jklm.no>
Reviewed-by: NDavid Herrmann <dh.herrmann@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some drivers (such as iwlmvm) can handle multiple bands in a single
HW scan request. Add a HW flag to indicate that the driver support
this. To hold the required data, create a separate structure for
HW scan request that holds cfg scan request and data about
different parts of the scan IEs.

As this changes the mac80211 API, update all drivers using it to
use the correct new function type/argument.
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Using perm_addr is always wrong, it may be reassigned by
anyone using standard netdev APIs. Remove that from the
match function and also use the match function where only
the perm_addr was used now.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

mac80211 takes care of all the needed steps for hwsim, so indicate
support for this capability.
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This will allow the low level driver to make decision based
on the vif such as queues etc...
Since the vif might be NULL, we can't add it to the tracing
functions.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
[fix staging rtl8821ae driver]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add a new HWSIM_ATTR_USE_CHANCTX attribute to the
HWSIM_CMD_CREATE_RADIO command to allow the creation of radios with
one channel that use channel contexts.  If this attribute is not
present, the behaviour is the same as before (ie. single channel
radios don't use channel contexts and multi channel radios do).
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There's little point in setting the number of channels if the
entire combination struct is overwritten again later - that
was clearly intended the other way around, fix it.
Reported-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The purpose of this housekeeping is to make some room for
VHT flags. The radiotap vendor fields weren't in use.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>