Add more items to sensitivity range table to avoid using hardcoded values.
Initialize the table per device since unique per device information is
required to perform sensitivity calibration.

additional items in sensitivity range table:
   .barker_corr_th_min: Barker correlation threshold minimum
   .barker_corr_th_min_mrc: Barker correlation threshold minimum for MRC
   .nrg_th_cca: Energy threshold for Clear Channel Assessment

Barker codes are a technique used in WLAN encoding for transmission.
MRC is "Maximal Ratio Combining", a technique for optimally combining the
signals from 2 or more receivers to achieve a better signal.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

"IWL_CMD_QUEUE_NUM" is being defined in multiple places and used by all
the devices. move it to iwl-dev.h file and shared by all the devices.

Remove "IWL_CMD_FIFO_NUM", replaced by "IWL49_CMD_FIFO_NUM" and IWL50_CMD_FIFO_NUM"
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Clean up device-specific apm_reset() functions and library infrastructure,
now that these reset() functions are no longer being used.
Signed-off-by: NBen Cahill <ben.m.cahill@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Now that we're unconditionally using apm_ops.stop() to reset and power-down
the device in __iwl3945_down(), the apm_ops.reset() is redundant.  Removing
this call will also allow us to remove iwl3945_apm_reset().

Remove unneeded iwl_clear_bit(CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ) because
this bit will be set again very soon in iwl3945_hw_txq_ctx_stop() and other
following calls.
Signed-off-by: NBen Cahill <ben.m.cahill@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In some cases (e.g. when mac80211 calls iwl_mac_stop() for suspend or user
no longer wants device active), device has not been going into low power state
via __iwl_down().  apm_ops.reset() does not put device into low power state;
instead it resets the device, then puts it into a powered-up state ready to be
re-loaded with uCode and re-started.  This has needlessly warmed up user's
laptops and drained batteries.

With current architecture in which mac80211 controls device up/down (including
resetting device after firmware errors), there is no need for apm_ops.reset()
any more; apm_ops.reset() is basically a combination of apm_ops.stop() and
apm_ops.init().

Instead, __iwl_down() now unconditionally places the device into a low-power
state via apm_ops.stop(). Device may be re-started via __iwl_up() calling
apm_ops.init() as soon as it may be needed (e.g. quickly for firmware errors),
but in the meantime, device will stop wasting energy.

Note that, even in this low power state, if driver re-enables interrupts,
the device retains the ability to sense the hardware RF-KILL switch, and
(except for 3945) interrupt the host when it changes.
Signed-off-by: NBen Cahill <ben.m.cahill@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Update iwl3945_apm_init() to set up device registers in sequence most recently
recommended by factory.

Add resets for APMG interrupts and radio chip, formerly done only in
iwl3945_apm_reset(); moving them here assures that apm_init() will do
a complete job of preparing hardware not only after platform boot,
but also after apm_stop() has executed (due to rfkill, ifconfig down,
driver unload, etc.).  This is in preparation to completely remove apm_reset().

Add some comments.
Signed-off-by: NBen Cahill <ben.m.cahill@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some airo card don't support power Management [1].
Don't abort suspend with those cards.

00:06.0 Network controller: AIRONET Wireless Communications PC4800 (rev 01)
        Flags: medium devsel, IRQ 17
        Memory at dffffe00 (32-bit, non-prefetchable) [size=128]
        I/O ports at d000 [size=128]
        I/O ports at cc00 [size=64]
        Kernel driver in use: airo
Signed-off-by: NMatthieu CASTET <castet.matthieu@free.fr>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove me
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This slightly shrinks the structure.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We must check the bustype before using the host_pci pointer.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When TX is hung, the chip is reset. Ensure that
the chip is awake by using the PS wrappers.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Return status of lbs_prepare_and_send_command and lbs_cmd_with_response
functions is not checked at some places. Those checks are added.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently several events are enabled from the firmware for which there
is no handling. This wakes up the host unnecessarily. Mask those
unneeded events.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Enable beacon filtering when PSM is enabled
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Enable beacon filtering with the mac80211 stack.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add configuration for connection monitor (number of allowed beacons, and
timeout after last received beacon.)
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use vmalloc to allocate memory for the firmware image, and use a smaller
linear buffer for the actual transfer of the firmware to the chipset.

This patch is an adaptation of a similar patch for wl1251 by Kalle Valo.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Enable multicast filtering. This way by default no multicast frames will
reach the host, and when needed, only required multicast frames can be
passed from the WLAN chipset to the host.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Clear the probe-request template on the firmware after scan. Unless
cleared, the firmware can independently send probe requests to the AP
and interfere with the mac80211 logic.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use the workqueue provided by the mac80211 stack instead of the system
default queue.

Modified to use new ieee_queue_work() as required by changes in the
stack.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is a hack to disable all filters in the join command.  This is based on
Kalle Valo's patch for wl1251.

Cc: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add Juuso as one of the module authors, since he's working heavily on this
module as well.

Cc: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Corrections to the TX path - use correct number of maximum descriptors
(32 instead of 16) and correct checking and setting of excessive retries
on completion.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Update the usage of join's, including using actual beacon interval and
dtim from AP, and configuring a basic rate set from AP.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Configure the rate policies to the firmware based on the rates given by
the AP.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds implementation for checking for SPI busy words - i.e.
honoring a delay request from the WLAN chipset upon reading
registers/memory.

To optimized the average SPI ready by 32 bits, also configure the number
of busywords to one to disable the "fixed-busy-word" functionality.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NVidhya Govindan <vidhya.govindan@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In ps-poll template aid bits 14 and 15 were not masked as required by
the standard. Mask them so that aid is sent in correct format.

This patch is a direct port of the respective patch for the wl1251
driver by Kalle Valo.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NVidhya Govindan <vidhya.govindan@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Implement delayed entry into ELP. This will promote the following:
 - Less redundant sleep/wake cycles (better perf)
 - Avoids known firmware issues with going to ELP too fast after an
   operation
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NVidhya Govindan <vidhya.govindan@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Correct the position to which TKIP header space is appended for TX
packets.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NVidhya Govindan <vidhya.govindan@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add security sequence number handling to the driver TX data path needed
by WPA.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Correct the TX path implementation to allocate sufficient blocks in the
firmware for TX packets.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The qual element in ieee80211_rx_status is not used anymore, so we don't need
to set it in the wl1271_rx_status() function.  This saves a bit of time in
the RX path.
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NDavid Kilroy <kilroyd@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The PA calibration for ar9271 ath9k_hw_9271_pa_cal() can run during
reset or initial calibration, update the PA calibration to account
for that and initialize PA calibration variables for both conditions.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is required for the ar9271 hardware as well.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The 'XFP' driver is really a driver for the QT2022C2 and QT2025C PHYs,
covering both more and less than XFP.  Rename its functions and
constants to reflect reality and to reduce namespace pollution when
sfc is a built-in driver.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The only multi-speed PHY driver using this is 10Xpress, and it does
not support non-autoneg operation.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

efx_fc_resolve() is specific to MDIO and is not used by any other
function.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MTD partition is named based on the netdev name, which is set to
'eth%d' before registration.  Also, the MTD partition will currently
be left registered if netdev registration fails.

Fix both these problems by moving the MTD probe after netdev
registration.  Hold the RTNL to serialise this with the netdev
notifier that calls efx_mtd_rename().
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These cleanup functions will never be called if the MMIO region could
not be mapped.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>