This enum is already perfectly aliased to enum nl80211_band, and
the only reason for it is that we get IEEE80211_NUM_BANDS out of
it. There's no really good reason to not declare the number of
bands in nl80211 though, so do that and remove the cfg80211 one.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When starting a PCP, pass the is_go flag to firmware in
wmi_pcp_start. This flag indicates whether we started
a PCP which is also a GO(P2P group owner) or just a regular
PCP.
Signed-off-by: NLior David <qca_liord@qca.qualcomm.com>
Signed-off-by: NMaya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Added support for the P2P_DEVICE virtual interface. This interface
is intended for P2P management operations such as discovery and
GO negotiation. Normally it is implemented by drivers to allow
a separate interface for P2P management with its own MAC address,
but for 11ad drivers it is needed to support P2P search, since it
cannot otherwise be separated from normal scan.

Since we only support a single interface/MAC address, we can't
easily separate between primary and P2P_DEVICE interfaces.
For example when a management packet arrives we can't tell for
which interface it is intended. To work around this, we store
a pointer to the interface where the last "radio operation" was
triggered such as scan or remain on channel, and we forward
management packets and scan results to this interface.
Signed-off-by: NLior David <qca_liord@qca.qualcomm.com>
Signed-off-by: NMaya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

supporting p2p_find, p2p_listen and p2p_connect
Use updated cfg80211_get_bss API (additional argument)
Signed-off-by: NDedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: NLior David <qca_liord@qca.qualcomm.com>
Signed-off-by: NMaya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Switch to auto-generated version of wmi.h which is maintained
by FW team. This will allow better sync between teams in the
future and avoid bugs because of unexpected API changes.
The wmi.h will have many differences but most are cosmetic.
It also includes these real differences:
1. is_go parameter added to BCON_CTRL and START_PCP commands.
2. max_rx_pl_per_desc added to CFG_RX_CHAIN command.
3. various small API updates that are not currently used by
driver.
Signed-off-by: NLior David <qca_liord@qca.qualcomm.com>
Signed-off-by: NMaya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

wmi_evt_connect doesn't check if the connect event is received for
an already connected station.
This can lead to memory leak as a new vring is allocated without
freeing the previously allocated vring and to unexpected behavior
of nl80211 layer due to unexpected notification of a new station.

Add a check in wmi_evt_connect in AP mode to verify that the requested
CID is not associated to an already connected station.
Signed-off-by: NMaya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

In case there are multiple WMI commands with the same reply_id,
the following scenario can occur:
- Driver sends the first command to the device
- The reply didn’t get on time and there is timeout
- Reply_id, reply_buf and reply_size are set to 0
- Driver sends second wmi command with the same reply_id as the first
- Driver sets wil->reply_id
- Reply for the first wmi command arrives and handled by wmi_recv_cmd
- As its ID fits the reply_id but the reply_buf is not set yet it is
handled as a reply with event handler, and WARN_ON is printed

This patch guarantee atomic setting of all the reply variables and
prevents the above scenario.
Signed-off-by: NMaya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

In the current solution wil6210 configures the vring in a worker
and holds only one pending CID. This implementation may lead to
race conditions between connect and disconnect events of multiple
stations or fast connect/disconnect events of the same station.

In order to allow the removal of the connect worker and handling of
WMI_VRING_CFG_DONE_EVENTID in the connect event, the WMI replies
that provide the reply in a given buffer needs to be handled
immediately in the WMI event interrupt thread.
To prevent deadlocks, WMI replies that requires additional
handling are still handled via the events list.
Signed-off-by: NMaya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

In __wmi_send we check if fw is ready at the beginning of the function.
While we wait for the completion of the previous command, system suspend
can be invoked and reset the HW, causing __wmi_send to read from HW
registers while it is not ready.
Taking the wmi_mutex in the reset flow when setting the FW ready bit
to zero will prevent the above race condition.
Signed-off-by: NMaya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Adjust driver behavior during FW boot. Proper sequence of
events after reset and FW download, is as following:

- FW prepares mailbox structure and reports IRQ "FW_READY"
- driver caches mailbox registers, marks mailbox readiness
- FW sends WMI_FW_READY event, ignore it
- FW sends WMI_READY event with some data
- driver stores relevant data marks FW is operational
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Some events are ignored for purpose; such events should not
be treated as "unhandled events". Replace info message
saying "unhandled" with debug one saying "ignore", to reduce
dmesg pollution
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

For the sniffer (monitor) mode, capture either control only or both
control and data PHY.

It used to be control only or data only PHY due to firmware
issues with configuration for PHY auto-detection; but now
it is resolved.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Return type of wait_for_completion_timeout is unsigned long not int.
As remain is exclusively used for wait_for_completion_timeout here its
type is simply changed to unsigned long.

API conformance testing for completions with coccinelle spatches are being
used to locate API usage inconsistencies:
./drivers/net/wireless/ath/wil6210/wmi.c:827
	int return assigned to unsigned long

Patch was compile tested with x86_64_defconfig + CONFIG_ATH_CARDS=m,
CONFIG_WIL6210=m

Patch is against 4.1-rc3 (localversion-next is -next-20150514)
Signed-off-by: NNicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Replace macros like "R", "W", "S", "C", defined multiple times,
with inline functions "wil_[rwsc]".

Use "readl" and "writel" instead of "ioread32" and "iowrite32"
since it is granted that memory transactions are used,
not port ones like IN/OUT
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

When printing error message, provide string describing IE kind.
Derive it from IE type
This allows removing of error messages printing
in callers
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

FW is allowed to generate WMI events that are not handled by this driver.
Treat such case as warning instead of error.
Signed-off-by: NDedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Check event length;
hex dump both Rx and Tx frames
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Multiple del_station requests may be sent to the driver by the
supplicant when turning down AP. This may overflow mailbox
between the FW and ucode

Wait till disconnect of one STA completed before sending next command.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Pass hidden SSID information to FW for proper operation.
In order to be able to scan/connect to the hidden SSID, SSID
setting is added when scan is requested from FW. SSID
scanning currently supports single SSID due to FW limitation.
Signed-off-by: NHamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Firmware defines new memory region, mac_rgf_ext
that need to be accessed from the host for debug purposes.

Add corresponded mapping
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Introduce 2 types of GTK, Tx (for this STA) and Rx (for each peer).
Now, AP has only Tx GTK, STA - only Rx one. PBSS not supported yet;
for it, continue using pseudo-DMS.
Handle per-vring .1x state, update it from WMI_VRING_EN_EVENTID
event. This allows unification for unicast and broadcast vrings.
This mechanism replaces former per-CID "data_port_open"
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Sometimes it takes for the firmware more than 20ms to
react on "echo" command after reset. Increase timeout
from 20 to 50ms
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Fix checkpatch warning:
WARNING: Prefer ether_addr_copy() over memcpy() if the
Ethernet addresses are __aligned(2)
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

For the networking code and for hardware network accelerators,
it is better to have IP header 4*n aligned. On the other side,
DMA on Rx path require buffer to be aligned on 4*n as well.
Having 14 bytes of Ethernet header, these 2 alignment
requests are in contradiction.

To solve this, order hardware offload block to not remove
SNAP header. This adds extra 6 bytes between addresses and
ethertype, making it 20 bytes total. This way, both buffer and
IP header are 4*n aligned. Remaining is only to remove SNAP
by shifting addresses 6 bytes. This involves data copying, so
this feature should be disabled unless required by the platform.

Module parameter "rx_align_2" (bool, default - false)
introduced to control this feature. Feature is completely disabled
when parameter is false.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Make this field to track privacy attribute for all interface types
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Introduce boot loader. Instead of the operational firmware,
very small boot loader is burned to the on-board flash. Boot loader
initializes hardware upon reset, and prepares for low power mode.
Boot loader reports MAC address and detects radio chip connected.

Driver loads firmware only when bringing up interface. All information
required to set up network interface, most important is MAC address,
reported by the boot loader

The firmware composed of 2 files:
- wil6210.fw - firmware itself (compiled code + data)
- wil6210.board - board file (various board and radio dependent
  calibrations and parameters)
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

netif_carrier_on indication was too late. In case Rx packet received
before netif_carrier_on indication, upper layers could not send
Tx packet back.

The fix is to indicate netif_carrier_on earlier:
for STA, indicate netif_carrier_on when association starts.
for AP/PCP, indicate netif_carrier_on upon starting AP/PCP.
Signed-off-by: NDedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Incorporate changes from firmware.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

In the Rx reorder mechanism, nothing is done in the interrupt
context, so there is no need to use 'irq' flavors of spinlock.
Rx done in NAPI context (tasklet), other manipulations - in the
thread context.

Having interrupts enabled makes it better for the OS in general.
Besides, if enslaved under bonding, bridge or team driver, Rx
won't work with interrupts disabled.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Rx high threshold interrupt is reported by the hardware in case
when number of not utilized by the HW descriptors in the Rx ring
becomes low.
Introduce module parameter for RX high threshold.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

wil->status used as bitmap; use DECLARE_BITMAP for it.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Change default to support maximum number of associated
stations to an AP
Signed-off-by: NHamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When configuring Tx/Rx VRING's, driver need to specify max. MPDU size
It should take into account all overhead introduced by 802.3->208.11
transformation.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Implement delba flow for the responder (Rx) side
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When establishing Block Ack as originator (Tx), control
AMSDU flag when sending ADDBA and update status upon
establishment flow completion. To be used in AMSDU flows
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

For manual ADDBA configuration, allow to set desired window size or
disable automatic mechanism.

Introduce module parameter (int) agg_wsize. It can be changed on run time,
will be taken into account on the next connect. Interpretation:
- <0 - disable automatic ADDBA; intended for manual testing through debugfs
- 0 - use automatically calculated window size
- >0 - use this for window size. Clipped by maximum supported by the hardware
with current environment.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Upon Tx vring creation, initiate BACK establishment
with maximum possible window size.

When establishing secure connection, there is EAPOL data exchange
between connection itself and "data port open", where security
is done and non-EAPOL data may be transferred. It is better to
send EAPOL frames using normal ACK because of firmware considerations.

send ADDBA only is 2 conditions met:
- data port open for the corresponded STA
- vring created
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Introduce BACK establishment procedures; decision logic is not implemented
yet; debugfs entry 'addba' used to manually trigger addba/delba for ringid 0.

debugfs usage:
to establish BACK with agg_wsize 16:
  echo 16 > /sys/kernel/debug/ieee80211/phy0/wil6210/addba
to delete BACK:
  echo 0 > /sys/kernel/debug/ieee80211/phy0/wil6210/addba
to change agg_wsize, one need to delete BACK and establish it anew

ADDBA flow for:

- originator

Tx side (initiator) sends WMI_VRING_BA_EN_CMDID providing
agg_wsize and timeout parameters.
Eventually, it gets event confirming BACK agreement - WMI_BA_STATUS_EVENTID
with negotiated parameters. On this event, update Tx vring data
(struct vring_tx_data) and display BACK parameters on debugfs

- recipient

Rx side (recipient) firmware informs driver about ADDBA with
WMI_RCP_ADDBA_REQ_EVENTID, driver process it in service work
queue wq_service. It adjusts parameters and sends response
with WMI_RCP_ADDBA_RESP_CMDID, and final confirmation provided
by firmware with WMI_ADDBA_RESP_SENT_EVENTID. In case of success,
driver updates Rx BACK reorder buffer.

policy for BACK parameters:
- aggregation size (agg_wsize * MPDUsize)) to not exceed 64Kbytes

DELBA flow for:

- originator

driver decides to terminate BACK, it sends WMI_VRING_BA_DIS_CMDID
and updates struct vring_tx_data associated with vring; ignore
WMI_DELBA_EVENTID.

- recipient

firmware informs driver with WMI_DELBA_EVENTID,
driver deletes correspondent reorder buffer

ADDBA request processing requires sending WMI command, therefore
it is processed in work queue context. Same work queue used as for
connect, it get renamed to wq_service
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This is really just duplicating the list of information that's
already available in the nl80211 attribute, so remove the list.
Two small changes are needed:
 * remove STATION_INFO_ASSOC_REQ_IES complete, but the length
   (assoc_req_ies_len) can be used instead
 * add NL80211_STA_INFO_RX_DROP_MISC which exists internally
   but not in nl80211 yet

This gets rid of the duplicate maintenance of the two lists.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Propagate reason for the disconnect through the relevant call chains:
- report to cfg80211 reason as reported by the firmware
- provide to the firmware reason as requested by cfg80211
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>