Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, tmspci tokenring driver crashes on device initialization
because it requests its irq before initializing corresponding data
structures. Fix this by moving request_irq call to a safer place.
Signed-off-by: NMeelis Roos <mroos@linux.ee>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A commit c1b56878 "tc: policing requires
a rate estimator" introduced a test which invalidates previously working
configs, based on examples from iproute2: doc/actions/actions-general.
This is too rigorous: a rate estimator is needed only when police's
"avrate" option is used.
Reported-by: NJoao Correia <joaomiguelcorreia@gmail.com>
Diagnosed-by: NJohn Dykstra <john.dykstra1@gmail.com>
Signed-off-by: NJarek Poplawski <jarkao2@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 6833c043 introduced the phy
auto-powerdown capability.  While the APD feature only works for 5761
and 5784 asic revisions, the (harmless portion of the) code was applied
to all 5705 and newer devices.  However, the 5906 phy departs from the
usual design.  This commit was interfering with the 5906's ability to
negotiate link against some switches.  This patch corrects the problem.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change sctp_ctl_sock_init() to try IPv4 if IPv6 socket registration
fails.  Required if the IPv6 module is loaded with "disable=1", else
SCTP will fail to load.
Signed-off-by: NBrian Haley <brian.haley@hp.com>
Signed-off-by: NVlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add "disable" module parameter support to ipv6.ko by specifying
"disable=1" on module load.  We just do the minimum of initializing
inetsw6[] so calls from other modules to inet6_register_protosw()
won't OOPs, then bail out.  No IPv6 addresses or sockets can be
created as a result, and a reboot is required to enable IPv6.
Signed-off-by: NBrian Haley <brian.haley@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Another error was printed one too early.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

with while (i-- > 0); i reaches -1 after the loop, so the test below is printed
one too early: 0 still means success.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

with while (--worklimit >= 0); worklimit reaches -1 after the loop. In
3c589_cs.c this caused a warning not to be printed.

In 3c574_cs.c contrastingly, el3_rx() treats worklimit differently:

static int el3_rx(struct net_device *dev, int worklimit)
{
	while (--worklimit >= 0) { ... }
	return worklimit;
}

el3_rx() is only called by function el3_interrupt(): twice:

static irqreturn_t el3_interrupt(int irq, void *dev_id)
{
        int work_budget = max_interrupt_work;
	while(...) {
		if (...)
			work_budget = el3_rx(dev, work_budget);
		if (...)
			work_budget = el3_rx(dev, work_budget);
		if (--work_budget < 0) {
		        ...
		        break;
		}
	}
}
The error path can occur 2 too early.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

with while (timeout-- > 0); timeout reaches -1 after the loop, so the tests
below are off by one. also don't do an '< 0' test on an unsigned.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, modular tokenring ("tr") lacks a license and fails to load:

tr: module license 'unspecified' taints kernel.
tr: Unknown symbol proc_net_fops_create

Beacuse of this, no tokenring driver can load if it depends on modular 
tr. Fix this by adding GPL module license as it is in the kernel.

With this fix, tr module loads fine and tms380 driver also loads. Well, 
it does'nt work but that's a different bug.
Signed-off-by: NMeelis Roos <mroos@linux.ee>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add vendor/product IDs for new no name dm9601 compatible usb ethernet
adaptors.
Reported-by: NEric Lauriault <eric@linux.ca>
Signed-off-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The callers of netlink_set_err() currently pass a negative value
as parameter for the error code. However, sk->sk_err wants a
positive error value. Without this patch, skb_recv_datagram() called
by netlink_recvmsg() may return a positive value to report an error.

Another choice to fix this is to change callers to pass a positive
error value, but this seems a bit inconsistent and error prone
to me. Indeed, the callers of netlink_set_err() assumed that the
(usual) negative value for error codes was fine before this patch :).

This patch also includes some documentation in docbook format
for netlink_set_err() to avoid this sort of confusion.
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It turns out that net_alive is unnecessary, and the original problem
that led to it being added was simply that the icmp code thought
it was a network device and wound up being unable to handle packets
while there were still packets in the network namespace.

Now that icmp and tcp have been fixed to properly register themselves
this problem is no longer present and we have a stronger guarantee
that packets will not arrive in a network namespace then that provided
by net_alive in netif_receive_skb.  So remove net_alive allowing
packet reception run a little faster.

Additionally document the strong reason why network namespace cleanup
is safe so that if something happens again someone else will have
a chance of figuring it out.
Signed-off-by: NEric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To remove the possibility of packets flying around when network
devices are being cleaned up use reisger_pernet_subsys instead of
register_pernet_device.
Signed-off-by: NEric W. Biederman <ebiederm@aristanetworks.com>
Acked-by: NDenis V. Lunev <den@openvz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Recently I had a kernel panic in icmp_send during a network namespace
cleanup.  There were packets in the arp queue that failed to be sent
and we attempted to generate an ICMP host unreachable message, but
failed because icmp_sk_exit had already been called.

The network devices are removed from a network namespace and their
arp queues are flushed before we do attempt to shutdown subsystems
so this error should have been impossible.

It turns out icmp_init is using register_pernet_device instead
of register_pernet_subsys.  Which resulted in icmp being shut down
while we still had the possibility of packets in flight, making
a nasty NULL pointer deference in interrupt context possible.

Changing this to register_pernet_subsys fixes the problem in
my testing.
Signed-off-by: NEric W. Biederman <ebiederm@aristanetworks.com>
Acked-by: NDenis V. Lunev <den@openvz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a network namespace is destroyed the network interfaces are
all unregistered, making addrconf_ifdown called by the netdevice
notifier. 
In the other hand, the addrconf exit method does a loop on the network
devices and does addrconf_ifdown on each of them. But the ordering of 
the netns subsystem is not right because it uses the register_pernet_device
instead of register_pernet_subsys. If we handle the loopback as
any network device, we can safely use register_pernet_subsys.

But if we use register_pernet_subsys, the addrconf exit method will do
exactly what was already done with the unregistering of the network
devices. So in definitive, this code is pointless.

I removed the netns addrconf exit method and moved the code to the
addrconf cleanup function.
Signed-off-by: NDaniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Acked-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The following patch enables SMC911x support to work on the OMAP LDP
board.  Although the SMC911x driver will eventually be obsoleted, the
smsc911x patches are rather invasive for the -rc kernels.

Rather than risk destablising smsc911x, this simpler patch is preferred
to allow the network interface to work.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If ERROR chunk is received with too many error causes in ESTABLISHED
state, the kernel get panic.

This is because sctp limit the max length of cmds to 14, but while
ERROR chunk is received, one error cause will add around 2 cmds by
sctp_add_cmd_sf(). So many error causes will fill the limit of cmds
and panic.

This patch fixed the problem.

This bug can be test by SCTP Conformance Test Suite
<http://networktest.sourceforge.net/>.
Signed-off-by: NWei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: NVlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

An extra list_del() during the module load failure and unload
resulted in a crash with a list corruption.  Now sctp can
be unloaded again.
Signed-off-by: NVlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Motorola MOTOMAGX phones (Z6, E8, Zn5 so far) are providing
combined ACM/BLAN USB configuration. Since it has Vendor Specific
class, the corresponding drivers (cdc-acm, zaurus) can't find it just
by interface info. This patch adds usb id so the zaurus driver can
properly handle this combined device.
Signed-off-by: NDmitriy Taychenachev <dimichxp@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make usbnet_get_link() fall back to ethtool_op_get_link() instead of
defaulting to 1.  
     
This makes usbnet_get_link return valid results without the need for a
driver specific check_connect or mii ops as long as the driver calls
netif_carrier_{on,off}() as appropriate.  cdc_ether is an example of
such a driver.
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current implementation of carrier detect in veth is broken.
It reports the link is down until both sides of the veth pair
are administatively up and then forever after it reports link up.

So fix veth so that it only reports link up when both interfaces
of the pair are administratively up.
Signed-off-by: NEric Biederman <ebiederm@aristanetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Ericsson F3507g wireless broadband module provides a CDC Ethernet
compliant interface, but identifies it as a "Mobile Direct Line" CDC
subclass, thereby preventing the CDC Ethernet class driver from picking
it up.  This patch adds the device id to cdc_ether.c as a workaround.

Ericsson has provided a "class" driver for this device:
http://kerneltrap.org/mailarchive/linux-net/2008/10/28/3832094
But closer inspection of that driver reveals that it adds little more
than duplication of code from cdc_ether.c.  See also
http://marc.info/?l=linux-usb&m=123334979706403&w=2Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is 2nd attempt to implement the initialization/reading of MAC address
from EEPROM. The first used PCI's VPD and there were some problems, some
devices are not able to read EEPROM content by VPD. The 2nd one uses direct
access to EEPROM through bit-banging interface and my testing results seem
to be much better.

I tested 5 systems each with different Realtek NICs and I didn't find any
problem. AFAIK Francois's NICs also works fine.

Original description:
This fixes the problem when MAC address is set by ifconfig or by
ip link commands and this address is stored in the device after
reboot. The power-off is needed to get right MAC address.
This is problem when Xen daemon is running because it renames the device
name from ethX to pethX and sets its MAC address to FE:FF:FF:FF:FF:FF.
After reboot the device is still using FE:FF:FF:FF:FF:FF.
Signed-off-by: NIvan Vecera <ivecera@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There's conflicting assumptions in shifting, the caller assumes
that dupsack results in S'ed skbs (or a part of it) for sure but
never gave a hint to tcp_sacktag_one when dsack is actually in
use. Thus DSACK retrans_out -= pcount was not taken and the
counter became out of sync. Remove obstacle from that information
flow to get DSACKs accounted in tcp_sacktag_one as expected.
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Tested-by: NDenys Fedoryshchenko <denys@visp.net.lb>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The DCB netlink interface is required for building the userspace tools
available at e1000.sourceforge.net
Signed-off-by: NChris Leech <christopher.leech@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1) add an include for <linux/types.h>
2) change dcbmsg.dcb_family from unsigned char to __u8 to be more
   consistent with use of kernel types
Signed-off-by: NChris Leech <christopher.leech@intel.com>
Acked-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The netpoll entry checks are required to ensure that we don't
receive normal packets when invoked via netpoll.  Unfortunately
it only ever worked for the netif_receive_skb/netif_rx entry
points.  The VLAN (and subsequently GRO) entry point didn't
have the check and therefore can trigger all sorts of weird
problems.

This patch adds the netpoll check to all entry points.

I'm still uneasy with receiving at all under netpoll (which
apparently is only used by the out-of-tree kdump code).  The
reason is it is perfectly legal to receive all data including
headers into highmem if netpoll is off, but if you try to do
that with netpoll on and someone gets a printk in an IRQ handler                                             
you're going to get a nice BUG_ON.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
  Staging: w35und: fix usb_control_msg() error handling in wb35_probe()
  Staging: w35und: fix registration with wlan stack
  Staging: panel: fix oops on panel_cleanup_module
  Staging: rtl8187se: Fix oops and memory poison caused by builtin ieee80211.
  Staging: rtl8187se: fix Kconfig dependencies

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (21 commits)
  USB: musb: fix srp sysfs entry deletion
  USB: musb: resume suspended root hub on disconnect
  USB: musb: use right poll limit for low speed devices
  USB: musb: be careful with 64K+ transfer lengths, host side
  USB: musb: fix data toggle saving with shared FIFO
  USB: musb: host endpoint_disable() oops fixes
  USB: musb: fix urb_dequeue() method
  USB: musb: fix musb_host_tx() for shared endpoint FIFO
  USB: musb: be careful with 64K+ transfer lengths (gadget side)
  usb: musb: make Davinci *work* in mainline
  USB: usb_get_string should check the descriptor type
  USB: gadget: fix build error in omap_apollon_2420_defconfig
  USB: g_file_storage: automatically disable stalls under Atmel
  USB: usb-storage: add IGNORE_RESIDUE flag for Genesys Logic adapters
  USB: Quirk for Hummingbird huc56s / Conexant ACM modem
  USB: serial: add support for second revision of Ericsson F3507G WWAN card
  USB: cdc-acm: add usb id for motomagx phones
  USB: option: add BenQ 3g modem information
  usb: gadget: obex: select correct ep descriptors
  USB: EHCI: slow down ITD reuse
  ...

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  Revert "MIPS: Print irq handler description"
  MIPS: CVE-2009-0029: Enable syscall wrappers.
  MIPS: Alchemy: In plat_time_init() t reaches -1, tested: 0
  MIPS: Only allow Cavium OCTEON to be configured for boards that support it

Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86: enable DMAR by default
  xen: disable interrupts early, as start_kernel expects
  gpu/drm, x86, PAT: io_mapping_create_wc and resource_size_t
  gpu/drm, x86, PAT: Handle io_mapping_create_wc() errors in a clean way
  x86, Voyager: fix compile by lifting the degeneracy of phys_cpu_present_map
  x86, doc: fix references to Documentation/x86/i386/boot.txt

* 'sh/for-2.6.29' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
  sh: ap325rxa: Revert ov772x support.
  serial: sh-sci: fix overrun error handling for SH7785 SCIF.
  sh: Storage class should be before const qualifier

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
  V4L/DVB (10696): Remove outdated README for the flexcop-driver
  V4L/DVB (10695): Update Technisat card documentation
  V4L/DVB (10694): [PATCH] software IRQ watchdog for Flexcop B2C2 DVB PCI cards
  V4L/DVB (10663): soc-camera: fix S_CROP breakage on PXA and SuperH
  V4L/DVB (10659): em28xx: register device to soundcard for sysfs

Commit 8e961870 removed the FREEZE/THAW
handling in xfs_compat_ioctl but never added any compat handler back, so
now any freeze/thaw request from a 32-bit binary ond 64-bit userspace
will fail.

As these ioctls are 32/64-bit compatible two simple COMPATIBLE_IOCTL
entries in fs/compat_ioctl.c will do the job.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>