Due to IP_GRE GSO support, GRE can recieve non linear skb which
results in panic in case of GRE_CSUM.  Following patch fixes it by
using correct csum API.

Bug introduced in commit 6b78f16e (gre: add GSO support)
Signed-off-by: NPravin B Shelar <pshelar@nicira.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While sctp handling a duplicate COOKIE-ECHO and the action is
'Association restart', sctp_sf_do_dupcook_a() will processing
the unexpected COOKIE-ECHO for peer restart, but it does not set
the association state to SCTP_STATE_ESTABLISHED, so the association
could stuck in SCTP_STATE_SHUTDOWN_PENDING state forever.
This violates the sctp specification:
  RFC 4960 5.2.4. Handle a COOKIE ECHO when a TCB Exists
  Action
  A) In this case, the peer may have restarted. .....
     After this, the endpoint shall enter the ESTABLISHED state.

To resolve this problem, adding a SCTP_CMD_NEW_STATE cmd to the
command list before SCTP_CMD_REPLY cmd, this will set the restart
association to SCTP_STATE_ESTABLISHED state properly and also avoid
I-bit being set in the DATA chunk header when COOKIE_ACK is bundled
with DATA chunks.
Signed-off-by: NXufeng Zhang <xufeng.zhang@windriver.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Acked-by: NVlad Yasevich <vyasevich@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We did this for IPv4 in b49d3c1e "net: ipmr: limit MRT_TABLE
identifiers" but we need to do it for IPv6 as well.  On IPv6 the name
is "pim6reg" instead of "pimreg" so there is one less digit allowed.

The strcpy() is in ip6mr_reg_vif().
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We never want multicast MAC addresses in the Distributed ARP Table, so it's
best to completely ignore ARP packets containing them where we expect unicast
addresses.
Signed-off-by: NMatthias Schiffer <mschiffer@universe-factory.net>
Acked-by: NAntonio Quartulli <ordex@autistici.org>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>

There are more types of IP addresses that may appear in ARP packets that we
don't want to process. While some of these should never appear in sane ARP
packets, a 0.0.0.0 source is used for duplicate address detection and thus seen
quite often.
Signed-off-by: NMatthias Schiffer <mschiffer@universe-factory.net>
Acked-by: NAntonio Quartulli <ordex@autistici.org>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>

The callers of batadv_dat_snoop_incoming_arp_reply() assume the skb has been
freed when it returns true; fix this by calling kfree_skb before returning as
it is done in batadv_dat_snoop_incoming_arp_request().
Signed-off-by: NMatthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Acked-by: NAntonio Quartulli <ordex@autistici.org>
Signed-off-by: NAntonio Quartulli <ordex@autistici.org>

git commit 9cb3a50c (ipv4: Invalidate the socket cached route on
pmtu events if possible) introduced a refcount problem. We don't
get a refcount on the route if we get it from__sk_dst_get(), but
we need one if we want to reuse this route because __sk_dst_set()
releases the refcount of the old route. This patch adds proper
refcount handling for that case. We introduce a 'new' flag to
indicate that we are going to use a new route and we release the
old route only if we replace it by a new one.
Reported-by: NJulian Anastasov <ja@ssi.bg>
Signed-off-by: NSteffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 6a328d8c changed the update
logic for the socket but it does not update the SCM_RIGHTS update
as well. This patch is based on the net_prio fix commit

48a87cc2

    net: netprio: fd passed in SCM_RIGHTS datagram not set correctly

    A socket fd passed in a SCM_RIGHTS datagram was not getting
    updated with the new tasks cgrp prioidx. This leaves IO on
    the socket tagged with the old tasks priority.

    To fix this add a check in the scm recvmsg path to update the
    sock cgrp prioidx with the new tasks value.

Let's apply the same fix for net_cls.
Signed-off-by: NDaniel Wagner <daniel.wagner@bmw-carit.de>
Reported-by: NLi Zefan <lizefan@huawei.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: John Fastabend <john.r.fastabend@intel.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: netdev@vger.kernel.org
Cc: cgroups@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This implements a socket release callback function to check
if the socket cached route got invalid during the time
we owned the socket. The function is used from udp, raw
and ping sockets.
Signed-off-by: NSteffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The route lookup in ipv4_sk_update_pmtu() might return a route
different from the route we cached at the socket. This is because
standart routes are per cpu, so each cpu has it's own struct rtable.
This means that we do not invalidate the socket cached route if the
NET_RX_SOFTIRQ is not served by the same cpu that the sending socket
uses. As a result, the cached route reused until we disconnect.

With this patch we invalidate the socket cached route if possible.
If the socket is owened by the user, we can't update the cached
route directly. A followup patch will implement socket release
callback functions for datagram sockets to handle this case.
Reported-by: NYurij M. Plotnikov <Yurij.Plotnikov@oktetlabs.ru>
Signed-off-by: NSteffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On IPsec pmtu events we can't access the transport headers of
the original packet, so we can't find the socket that sent
the packet. The only chance to notify the socket about the
pmtu change is to force a relookup for all routes. This
patch implenents this for the IPsec protocols.
Signed-off-by: NSteffen Klassert <steffen.klassert@secunet.com>

Missing multiplication of block size by sizeof(struct hlist_head)
can cause xfrm_hash_free() to be called with wrong second argument
so that kfree() is called on a block allocated with vzalloc() or
__get_free_pages() or free_pages() is called with wrong order when
a namespace with enough policies is removed.

Bug introduced by commit a35f6c5d, i.e. versions >= 2.6.29 are
affected.
Signed-off-by: NMichal Kubecek <mkubecek@suse.cz>
Signed-off-by: NSteffen Klassert <steffen.klassert@secunet.com>

commit 9ca1b22d (net: splice: avoid high order page splitting)
forgot that skb->head could need a copy into several page frags.

This could be the case for loopback traffic mostly.

Also remove now useless skb argument from linear_to_page()
and __splice_segment() prototypes.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Willy Tarreau <w@1wt.eu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

splice() can handle pages of any order, but network code tries hard to
split them in PAGE_SIZE units. Not quite successfully anyway, as
__splice_segment() assumed poff < PAGE_SIZE. This is true for
the skb->data part, not necessarily for the fragments.

This patch removes this logic to give the pages as they are in the skb.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Willy Tarreau <w@1wt.eu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit 563d34d0 (tcp: dont drop MTU reduction indications)
added an error leading to incorrect accounting of
LINUX_MIB_LOCKDROPPEDICMPS

If socket is owned by the user, we want to increment
this SNMP counter, unless the message is a
(ICMP_DEST_UNREACH,ICMP_FRAG_NEEDED) one.
Reported-by: NMaciej Żenczykowski <maze@google.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Signed-off-by: NMaciej Żenczykowski <maze@google.com>
Acked-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

pmtu and redirect events are now handled in the protocols error handler,
so add an error handler for icmp6 to do this. It is needed in the case
when we have no socket context. Based on a patch by Duan Jiong.
Reported-by: NDuan Jiong <djduanjiong@gmail.com>
Signed-off-by: NSteffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All of the xfrm_replay->advance functions in xfrm_replay.c check if
x->replay_esn->replay_window is zero (and return if so).  However,
one of them, xfrm_replay_advance_bmp(), divides by that value (in the
'%' operator) before doing the check, which can potentially trigger
a divide-by-zero exception.  Some compilers will also assume that the
earlier division means the value cannot be zero later, and thus will
eliminate the subsequent zero check as dead code.

This patch moves the division to after the check.
Signed-off-by: NNickolai Zeldovich <nickolai@csail.mit.edu>
Signed-off-by: NSteffen Klassert <steffen.klassert@secunet.com>

Jamie Parsons reported a problem recently, in which the re-initalization of an
association (The duplicate init case), resulted in a loss of receive window
space.  He tracked down the root cause to sctp_outq_teardown, which discarded
all the data on an outq during a re-initalization of the corresponding
association, but never reset the outq->outstanding_data field to zero.  I wrote,
and he tested this fix, which does a proper full re-initalization of the outq,
fixing this problem, and hopefully future proofing us from simmilar issues down
the road.
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
Reported-by: NJamie Parsons <Jamie.Parsons@metaswitch.com>
Tested-by: NJamie Parsons <Jamie.Parsons@metaswitch.com>
CC: Jamie Parsons <Jamie.Parsons@metaswitch.com>
CC: Vlad Yasevich <vyasevich@gmail.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: netdev@vger.kernel.org
Acked-by: NVlad Yasevich <vyasevich@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Routes with locked mtu should not use learned pmtu informations,
so do not update the pmtu on these routes.
Reported-by: NJulian Anastasov <ja@ssi.bg>
Signed-off-by: NSteffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The output route check was introduced with git commit 261663b0
(ipv4: Don't use the cached pmtu informations for input routes)
during times when we cached the pmtu informations on the
inetpeer. Now the pmtu informations are back in the routes,
so this check is obsolete. It also had some unwanted side effects,
as reported by Timo Teras and Lukas Tribus.
Signed-off-by: NSteffen Klassert <steffen.klassert@secunet.com>
Acked-by: NTimo Teräs <timo.teras@iki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 299b0767 (ipv6: Fix IPsec slowpath fragmentation problem)
has introduced a error in the header length calculation that
provokes corrupted packets when non-fragmentable extensions
headers (Destination Option or Routing Header Type 2) are used.

rt->rt6i_nfheader_len is the length of the non-fragmentable
extension header, and it should be substracted to
rt->dst.header_len, and not to exthdrlen, as it was done before
commit 299b0767.

This patch reverts to the original and correct behavior. It has
been successfully tested with and without IPsec on packets
that include non-fragmentable extensions headers.
Signed-off-by: NRomain Kuntz <r.kuntz@ipflavors.com>
Acked-by: NSteffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Mesh PERR action frames are robust and thus may be encrypted, so add
proper head/tailroom to allow this.  Fixes this warning when operating
a Mesh STA on ath5k:

WARNING: at net/mac80211/wpa.c:427 ccmp_encrypt_skb.isra.5+0x7b/0x1a0 [mac80211]()
Call Trace:
 [<c011c5e7>] warn_slowpath_common+0x63/0x78
 [<c011c60b>] warn_slowpath_null+0xf/0x13
 [<e090621d>] ccmp_encrypt_skb.isra.5+0x7b/0x1a0 [mac80211]
 [<e090685c>] ieee80211_crypto_ccmp_encrypt+0x1f/0x37 [mac80211]
 [<e0917113>] invoke_tx_handlers+0xcad/0x10bd [mac80211]
 [<e0917665>] ieee80211_tx+0x87/0xb3 [mac80211]
 [<e0918932>] ieee80211_tx_pending+0xcc/0x170 [mac80211]
 [<c0121c43>] tasklet_action+0x3e/0x65
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

A user reported warnings in ath5k due to transmitting frames with no
rates set up.  The frames were Mesh PERR frames, and some debugging
showed an empty control block with just the vif pointer:

>  [  562.522682] XXX txinfo: 00000000: 00 00 00 00 00 00 00 00 00 00 00
>  00 00 00 00 00  ................
>  [  562.522688] XXX txinfo: 00000010: 00 00 00 00 00 00 00 00 54 b8 f2
>  db 00 00 00 00  ........T.......
>  [  562.522693] XXX txinfo: 00000020: 00 00 00 00 00 00 00 00 00 00 00
>  00 00 00 00 00  ................

Set the IEEE80211_TX_INTFL_NEED_TXPROCESSING flag to ensure that
rate control gets run before the frame is sent.
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Channel contexts are not always used with monitor interfaces. If no channel
context is set, use the oper channel, otherwise tx fails.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
[check local->use_chanctx]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Since:

commit b23b025f
Author: Ben Greear <greearb@candelatech.com>
Date:   Fri Feb 4 11:54:17 2011 -0800

    mac80211: Optimize scans on current operating channel.

we do not disable PS while going back to operational channel (on
ieee80211_scan_state_suspend) and deffer that until scan finish.
But since we are allowed to send frames, we can send a frame to AP
without PM bit set, so disable PS on AP side. Then when we switch
to off-channel (in ieee80211_scan_state_resume) we do not enable PS.
Hence we are off-channel with PS disabled, frames are not buffered
by AP.

To fix remove offchannel_ps_disable argument and always enable PS when
going off-channel and disable it when going on-channel, like it was
before.

Cc: stable@vger.kernel.org # 2.6.39+
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Tested-by: NSeth Forshee <seth.forshee@canonical.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

During FT roaming, wpa_supplicant attempts to set the
key before association. This used to be rejected, but
as a side effect of my commit 66e67e41
("mac80211: redesign auth/assoc") the key was accepted
causing hardware crypto to not be used for it as the
station isn't added to the driver yet.

It would be possible to accept the key and then add it
to the driver when the station has been added. However,
this may run into issues with drivers using the state-
based station adding if they accept the key only after
association like it used to be.

For now, revert to the behaviour from before the auth
and assoc change.

Cc: stable@vger.kernel.org
Reported-by: NCédric Debarge <cedric.debarge@acksys.fr>
Tested-by: NCédric Debarge <cedric.debarge@acksys.fr>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

spin_is_locked() on a non !SMP build is kind of useless.

BUG_ON(!spin_is_locked(xx)) is guaranteed to crash.

Just remove this check in reqsk_fastopen_remove() as
the callers do hold the socket lock.
Reported-by: NKetan Kulkarni <ketkulka@gmail.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Jerry Chu <hkchu@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Dave Taht <dave.taht@gmail.com>
Acked-by: NH.K. Jerry Chu <hkchu@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

arptables 0.0.4 (released on 10th Jan 2013) supports calling the
CLASSIFY target, but on adding a rule to the wrong chain, the
diagnostic is as follows:

	# arptables -A INPUT -j CLASSIFY --set-class 0:0
	arptables: Invalid argument
	# dmesg | tail -n1
	x_tables: arp_tables: CLASSIFY target: used from hooks
	PREROUTING, but only usable from INPUT/FORWARD

This is incorrect, since xt_CLASSIFY.c does specify
(1 << NF_ARP_OUT) | (1 << NF_ARP_FORWARD).

This patch corrects the x_tables diagnostic message to print the
proper hook names for the NFPROTO_ARP case.

Affects all kernels down to and including v2.6.31.
Signed-off-by: NJan Engelhardt <jengelh@inai.de>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

canqun zhang reported that we're hitting BUG_ON in the
nf_conntrack_destroy path when calling kfree_skb while
rmmod'ing the nf_conntrack module.

Currently, the nf_ct_destroy hook is being set to NULL in the
destroy path of conntrack.init_net. However, this is a problem
since init_net may be destroyed before any other existing netns
(we cannot assume any specific ordering while releasing existing
netns according to what I read in recent emails).

Thanks to Gao feng for initial patch to address this issue.
Reported-by: Ncanqun zhang <canqunzhang@gmail.com>
Acked-by: NGao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

Since:

commit 2c60db03
Author: Eric Dumazet <edumazet@google.com>
Date:   Sun Sep 16 09:17:26 2012 +0000

    net: provide a default dev->ethtool_ops

wireless core does not correctly assign ethtool_ops.

After alloc_netdev*() call, some cfg80211 drivers provide they own
ethtool_ops, but some do not. For them, wireless core provide generic
cfg80211_ethtool_ops, which is assigned in NETDEV_REGISTER notify call:

        if (!dev->ethtool_ops)
                dev->ethtool_ops = &cfg80211_ethtool_ops;

But after Eric's commit, dev->ethtool_ops is no longer NULL (on cfg80211
drivers without custom ethtool_ops), but points to &default_ethtool_ops.

In order to fix the problem, provide function which will overwrite
default_ethtool_ops and use it by wireless core.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Acked-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit c3ae62af (tcp: should drop incoming frames without ACK flag
set) added a regression on the handling of RST messages.

RST should be allowed to come even without ACK bit set. We validate
the RST by checking the exact sequence, as requested by RFC 793 and
5961 3.2, in tcp_validate_incoming()
Reported-by: NEric Wong <normalperson@yhbt.net>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Acked-by: NNeal Cardwell <ncardwell@google.com>
Tested-by: NEric Wong <normalperson@yhbt.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix new kernel-doc warnings in clnt.c:

  Warning(net/sunrpc/clnt.c:561): No description found for parameter 'flavor'
  Warning(net/sunrpc/clnt.c:561): Excess function parameter 'auth' description in 'rpc_clone_client_set_auth'
Signed-off-by: NRandy Dunlap <rdunlap@infradead.org>
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: linux-nfs@vger.kernel.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Replace ip6_route_lookup() with addrconf_get_prefix_route() when
looking up for a prefix route. This ensures that the connected prefix
is looked up in the main table, and avoids the selection of other
matching routes located in different tables as well as blackhole
or prohibited entries.

In addition, this fixes an Opps introduced by commit 64c6d08e (ipv6:
del unreachable route when an addr is deleted on lo), that would occur
when a blackhole or prohibited entry is selected by ip6_route_lookup().
Such entries have a NULL rt6i_table argument, which is accessed by
__ip6_del_rt() when trying to lock rt6i_table->tb6_lock.

The function addrconf_is_prefix_route() is not used anymore and is
removed.

[v2] Minor indentation cleanup and log updates.
Signed-off-by: NRomain Kuntz <r.kuntz@ipflavors.com>
Acked-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: NYOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The tests on the flags in addrconf_get_prefix_route() does no make
much sense: the 'noflags' parameter contains the set of flags that
must not match with the route flags, so the test must be done
against 'noflags', and not against 'flags'.
Signed-off-by: NRomain Kuntz <r.kuntz@ipflavors.com>
Acked-by: NYOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Under unusual circumstances, TCP collapse can split a big GRO TCP packet
while its being used in a splice(socket->pipe) operation.

skb_splice_bits() releases the socket lock before calling
splice_to_pipe().

[ 1081.353685] WARNING: at net/ipv4/tcp.c:1330 tcp_cleanup_rbuf+0x4d/0xfc()
[ 1081.371956] Hardware name: System x3690 X5 -[7148Z68]-
[ 1081.391820] cleanup rbuf bug: copied AD3BCF1 seq AD370AF rcvnxt AD3CF13

To fix this problem, we must eat skbs in tcp_recv_skb().

Remove the inline keyword from tcp_recv_skb() definition since
it has three call sites.
Reported-by: NChristian Becker <c.becker@traviangames.com>
Cc: Willy Tarreau <w@1wt.eu>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Tested-by: NWilly Tarreau <w@1wt.eu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit 02275a2e (tcp: don't abort splice() after small transfers)
added a regression.

[   83.843570] INFO: rcu_sched self-detected stall on CPU
[   83.844575] INFO: rcu_sched detected stalls on CPUs/tasks: { 6} (detected by 0, t=21002 jiffies, g=4457, c=4456, q=13132)
[   83.844582] Task dump for CPU 6:
[   83.844584] netperf         R  running task        0  8966   8952 0x0000000c
[   83.844587]  0000000000000000 0000000000000006 0000000000006c6c 0000000000000000
[   83.844589]  000000000000006c 0000000000000096 ffffffff819ce2bc ffffffffffffff10
[   83.844592]  ffffffff81088679 0000000000000010 0000000000000246 ffff880c4b9ddcd8
[   83.844594] Call Trace:
[   83.844596]  [<ffffffff81088679>] ? vprintk_emit+0x1c9/0x4c0
[   83.844601]  [<ffffffff815ad449>] ? schedule+0x29/0x70
[   83.844606]  [<ffffffff81537bd2>] ? tcp_splice_data_recv+0x42/0x50
[   83.844610]  [<ffffffff8153beaa>] ? tcp_read_sock+0xda/0x260
[   83.844613]  [<ffffffff81537b90>] ? tcp_prequeue_process+0xb0/0xb0
[   83.844615]  [<ffffffff8153c0f0>] ? tcp_splice_read+0xc0/0x250
[   83.844618]  [<ffffffff814dc0c2>] ? sock_splice_read+0x22/0x30
[   83.844622]  [<ffffffff811b820b>] ? do_splice_to+0x7b/0xa0
[   83.844627]  [<ffffffff811ba4bc>] ? sys_splice+0x59c/0x5d0
[   83.844630]  [<ffffffff8119745b>] ? putname+0x2b/0x40
[   83.844633]  [<ffffffff8118bcb4>] ? do_sys_open+0x174/0x1e0
[   83.844636]  [<ffffffff815b6202>] ? system_call_fastpath+0x16/0x1b

if recv_actor() returns 0, we should stop immediately,
because looping wont give a chance to drain the pipe.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Willy Tarreau <w@1wt.eu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

net/netfilter/xt_CT.c: In function ‘xt_ct_tg_check_v1’:
net/netfilter/xt_CT.c:250:6: warning: ‘ret’ may be used uninitialized in this function [-Wmaybe-uninitialized]
net/netfilter/xt_CT.c: In function ‘xt_ct_tg_check_v0’:
net/netfilter/xt_CT.c:112:6: warning: ‘ret’ may be used uninitialized in this function [-Wmaybe-uninitialized]
Reported-by: NBorislav Petkov <bp@alien8.de>
Acked-by: NBorislav Petkov <bp@alien8.de>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

Checking only for sco_conn seems to not be enough and lead to NULL
dereferences in the code, check for hcon instead.

<1>[11340.226404] BUG: unable to handle kernel NULL pointer dereference at
0000000
8
<4>[11340.226619] EIP is at __sco_sock_close+0xe8/0x1a0
<4>[11340.226629] EAX: f063a740 EBX: 00000000 ECX: f58f4544 EDX: 00000000
<4>[11340.226640] ESI: dec83e00 EDI: 5f9a081f EBP: e0fdff38 ESP: e0fdff1c
<0>[11340.226674] Stack:
<4>[11340.226682]  c184db87 c1251028 dec83e00 e0fdff38 c1754aef dec83e00
00000000
e0fdff5c
<4>[11340.226718]  c184f587 e0fdff64 e0fdff68 5f9a081f e0fdff5c c1751852
d7813800
62262f10
<4>[11340.226752]  e0fdff70 c1753c00 00000000 00000001 0000000d e0fdffac
c175425c
00000041
<0>[11340.226793] Call Trace:
<4>[11340.226813]  [<c184db87>] ? sco_sock_clear_timer+0x27/0x60
<4>[11340.226831]  [<c1251028>] ? local_bh_enable+0x68/0xd0
<4>[11340.226846]  [<c1754aef>] ? lock_sock_nested+0x4f/0x60
<4>[11340.226862]  [<c184f587>] sco_sock_shutdown+0x67/0xb0
<4>[11340.226879]  [<c1751852>] ? sockfd_lookup_light+0x22/0x80
<4>[11340.226897]  [<c1753c00>] sys_shutdown+0x30/0x60
<4>[11340.226912]  [<c175425c>] sys_socketcall+0x1dc/0x2a0
<4>[11340.226929]  [<c149ba78>] ? trace_hardirqs_on_thunk+0xc/0x10
<4>[11340.226944]  [<c18860f1>] syscall_call+0x7/0xb
<4>[11340.226960]  [<c1880000>] ? restore_cur+0x5e/0xd7
<0>[11340.226969] Code: <f0> ff 4b 08 0f 94 c0 84 c0 74 20 80 7b 19 01 74
2f b8 0a 00 00
Reported-by: NChuansheng Liu <chuansheng.liu@intel.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

If remote device sends l2cap info request before read_remote_ext_feature
completes then mgmt_connected will be sent in hci_acldata_packet() and
remote name request wont be sent and eventually authentication wont happen

Hcidump log of the issue

< HCI Command: Create Connection (0x01|0x0005) plen 13
    bdaddr BC:85:1F:74:7F:29 ptype 0xcc18 rswitch 0x01 clkoffset 0x4bf7 (valid)
    Packet type: DM1 DM3 DM5 DH1 DH3 DH5
> HCI Event: Command Status (0x0f) plen 4
    Create Connection (0x01|0x0005) status 0x00 ncmd 1
> HCI Event: Connect Complete (0x03) plen 11
    status 0x00 handle 12 bdaddr BC:85:1F:74:7F:29 type ACL encrypt 0x00
< HCI Command: Read Remote Supported Features (0x01|0x001b) plen 2
    handle 12
> HCI Event: Command Status (0x0f) plen 4
    Read Remote Supported Features (0x01|0x001b) status 0x00 ncmd 1
> HCI Event: Read Remote Supported Features (0x0b) plen 11
    status 0x00 handle 12
    Features: 0xbf 0xfe 0xcf 0xfe 0xdb 0xff 0x7b 0x87
> HCI Event: Max Slots Change (0x1b) plen 3
    handle 12 slots 5
< HCI Command: Read Remote Extended Features (0x01|0x001c) plen 3
    handle 12 page 1
> HCI Event: Command Status (0x0f) plen 4
    Read Remote Extended Features (0x01|0x001c) status 0x00 ncmd 1
> ACL data: handle 12 flags 0x02 dlen 10
    L2CAP(s): Info req: type 2
< ACL data: handle 12 flags 0x00 dlen 16
    L2CAP(s): Info rsp: type 2 result 0
      Extended feature mask 0x00b8
        Enhanced Retransmission mode
        Streaming mode
        FCS Option
        Fixed Channels
> HCI Event: Read Remote Extended Features (0x23) plen 13
    status 0x00 handle 12 page 1 max 1
    Features: 0x01 0x00 0x00 0x00 0x00 0x00 0x00 0x00
> ACL data: handle 12 flags 0x02 dlen 10
    L2CAP(s): Info req: type 3
< ACL data: handle 12 flags 0x00 dlen 20
    L2CAP(s): Info rsp: type 3 result 0
      Fixed channel list 0x00000002
        L2CAP Signalling Channel
> HCI Event: Number of Completed Packets (0x13) plen 5
    handle 12 packets 2

This patch moves sending mgmt_connected from hci_acldata_packet() to
l2cap_connect_req() since this code is to handle the scenario remote
device sends l2cap connect req too fast
Signed-off-by: NJaganath Kanakkassery <jaganath.k@samsung.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

The length parameter should be sizeof(req->name) - 1 because there is no
guarantee that string provided by userspace will contain the trailing
'\0'.

Can be easily reproduced by manually setting req->name to 128 non-zero
bytes prior to ioctl(HIDPCONNADD) and checking the device name setup on
input subsystem:

$ cat /sys/devices/pnp0/00\:04/tty/ttyS0/hci0/hci0\:1/input8/name
AAAAAA[...]AAAAAAAAf0:af:f0:af:f0:af

("f0:af:f0:af:f0:af" is the device bluetooth address, taken from "phys"
field in struct hid_device due to overflow.)

Cc: stable@vger.kernel.org
Signed-off-by: NAnderson Lizardo <anderson.lizardo@openbossa.org>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>