- 11 5月, 2010 22 次提交
-
-
由 Marek 提交于
This patch adds basic support for the Voipac PXA270 SBC. The device consists of the following hardware: - PXA270 @ 520 MHz - 256MB RAM (sparsemem, 2*128MB regions) - 64MB NOR flash - 640x480 LCD - Ports: 2xUHC, 1xUDC, 1xPCMCIA, VGA, FFUART, 2xPS2, Speaker, MIC Signed-off-by: NMarek Vasut <marek.vasut@gmail.com> Signed-off-by: NEric Miao <eric.y.miao@gmail.com>
-
由 Marek Vasut 提交于
This patch adds support for the Zipit Z2. The parts missing from this patch are the battery support, SPI driver for the LCD and support for the Silicon Serial ID chip. Signed-off-by: NMarek Vasut <marek.vasut@gmail.com> Signed-off-by: NEric Miao <eric.y.miao@gmail.com>
-
由 Igor Grinberg 提交于
CM-X300 bootloader passes DRAM configuration information in ATAGS, however, the first memory bank is reported at actual physical address 0x8000000. Use the configuration information supplied by the bootloader and cope with the necessity to have PHYS_ADDR=0xa0000000. Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il> Signed-off-by: NMike Rapoport <mike@compulab.co.il> Signed-off-by: NEric Miao <eric.y.miao@gmail.com>
-
由 Igor Grinberg 提交于
Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il> Signed-off-by: NEric Miao <eric.y.miao@gmail.com>
-
由 Igor Grinberg 提交于
Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il> Signed-off-by: NEric Miao <eric.y.miao@gmail.com>
-
由 Igor Grinberg 提交于
Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il> Signed-off-by: NEric Miao <eric.y.miao@gmail.com>
-
由 Igor Grinberg 提交于
Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il> Signed-off-by: NEric Miao <eric.y.miao@gmail.com>
-
由 Eric Miao 提交于
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>
-
由 Eric Miao 提交于
Tosa is now able to use generic matrix keypad driver instead of the deprecated tosakbd.c, where CONFIG_KEYBOARD_TOSA_USE_EXT_KEYCODES is still useful. Move it to mach/Kconfig. Signed-off-by: NEric Miao <eric.y.miao@gmail.com>
-
由 Eric Miao 提交于
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>
-
由 Eric Miao 提交于
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>
-
由 Eric Miao 提交于
REVISIT: change to GPIO18 is ugly, need to make sure whether that's really necessary - GPIO18_RDY as an VLIO input signal - we don't normally need to do such kind of trick during low power mode. Signed-off-by: NEric Miao <eric.y.miao@gmail.com>
-
由 Eric Miao 提交于
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>
-
由 Eric Miao 提交于
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>
-
由 Eric Miao 提交于
Some pins are expected to keep their last level during suspend, and introduce MFP_LPM_KEEP_OUTPUT for this. Signed-off-by: NEric Miao <eric.y.miao@gmail.com>
-
由 Eric Miao 提交于
PXA_SSP is actually used by drivers like drivers/spi/pxa2xx_spi.c and sound/soc/pxa/pxa-ssp.c, not by boards. Remove those incorrect 'select' from Kconfig and make SOC_PXA_SSP to select. Signed-off-by: NEric Miao <eric.y.miao@gmail.com>
-
由 Haojian Zhuang 提交于
Signed-off-by: NHaojian Zhuang <haojian.zhuang@marvell.com> Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: NEric Miao <eric.y.miao@gmail.com>
-
由 Eric Miao 提交于
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>
-
由 Eric Miao 提交于
No need to separate them as they should be together from the begining. Signed-off-by: NEric Miao <eric.y.miao@gmail.com>
-
由 Eric Miao 提交于
The previous definitions of SSCR0_SCR and SSCR0_SerClkDiv() prevented them being used simultaneously when supporting multiple PXA SoCs, esp. in drivers/spi/pxa2xx_spi.c, make them correct. The change from SSCR0_SerClkDiv(2) to SSCR0_SCR(2), will make the result a little bit different in pxa2xx_spi_probe(), however, since that's only used as a default initialization value, it's acceptable. Signed-off-by: NEric Miao <eric.y.miao@gmail.com>
-
由 Eric Miao 提交于
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>
-
由 Eric Miao 提交于
The only use of corgi_ssp.c is corgi_ts.c, which is now deprecated and removed. Remove corgi_ssp.c and corgi_lcd.c and their relevant function declarations and data structures. Signed-off-by: NEric Miao <eric.y.miao@gmail.com> Cc: Richard Purdie <rpurdie@rpsys.net> Cc: Pavel Machek <pavel@ucw.cz>
-
- 06 5月, 2010 6 次提交
-
-
由 Jakob Viketoft 提交于
The use of mfp_cfg_t causes build errors without including <mach/mfp.h>. CC: stable@kernel.org CC: Daniel Mack <daniel@caiaq.de> Signed-off-by: NJakob Viketoft <jakob.viketoft@bitsim.com> Signed-off-by: NEric Miao <eric.y.miao@gmail.com>
-
由 Pavel Machek 提交于
On/Off contains slash in the name, which causes warning during boot. Signed-off-by: NPavel Machek <pavel@ucw.cz> Signed-off-by: NEric Miao <eric.y.miao@gmail.com>
-
由 Haojian Zhuang 提交于
Fix the wrong variable used in cpu_is_pxa950(). Signed-off-by: NHaojian Zhuang <haojian.zhuang@marvell.com> Signed-off-by: NEric Miao <eric.y.miao@gmail.com>
-
由 Wolfram Sang 提交于
The timeout value is in jiffies, so it should be using HZ, not a plain number. Assume with HZ=100 '100' means 1s here and adapt accordingly. Signed-off-by: NWolfram Sang <w.sang@pengutronix.de> Acked-by: NMarc Zyngier <maz@misterjones.org> Cc: Russell King <linux@arm.linux.org.uk> Cc: Paul Shen <paul.shen@marvell.com> Cc: Mike Rapoport <mike@compulab.co.il> Cc: Jean Delvare <khali@linux-fr.org> Signed-off-by: NEric Miao <eric.y.miao@gmail.com>
-
由 Daniel Mack 提交于
"on/off button" was recently renamed to remove the slash character. Follow that change in the pin polarity detection as well. While at it, fix another cosmetic coding style flaw as well. Signed-off-by: NDaniel Mack <daniel@caiaq.de> Signed-off-by: NEric Miao <eric.y.miao@gmail.com>
-
由 Igor Grinberg 提交于
Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il> Signed-off-by: NEric Miao <eric.y.miao@gmail.com>
-
- 30 3月, 2010 1 次提交
-
-
由 Tejun Heo 提交于
include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h percpu.h is included by sched.h and module.h and thus ends up being included when building most .c files. percpu.h includes slab.h which in turn includes gfp.h making everything defined by the two files universally available and complicating inclusion dependencies. percpu.h -> slab.h dependency is about to be removed. Prepare for this change by updating users of gfp and slab facilities include those headers directly instead of assuming availability. As this conversion needs to touch large number of source files, the following script is used as the basis of conversion. http://userweb.kernel.org/~tj/misc/slabh-sweep.py The script does the followings. * Scan files for gfp and slab usages and update includes such that only the necessary includes are there. ie. if only gfp is used, gfp.h, if slab is used, slab.h. * When the script inserts a new include, it looks at the include blocks and try to put the new include such that its order conforms to its surrounding. It's put in the include block which contains core kernel includes, in the same order that the rest are ordered - alphabetical, Christmas tree, rev-Xmas-tree or at the end if there doesn't seem to be any matching order. * If the script can't find a place to put a new include (mostly because the file doesn't have fitting include block), it prints out an error message indicating which .h file needs to be added to the file. The conversion was done in the following steps. 1. The initial automatic conversion of all .c files updated slightly over 4000 files, deleting around 700 includes and adding ~480 gfp.h and ~3000 slab.h inclusions. The script emitted errors for ~400 files. 2. Each error was manually checked. Some didn't need the inclusion, some needed manual addition while adding it to implementation .h or embedding .c file was more appropriate for others. This step added inclusions to around 150 files. 3. The script was run again and the output was compared to the edits from #2 to make sure no file was left behind. 4. Several build tests were done and a couple of problems were fixed. e.g. lib/decompress_*.c used malloc/free() wrappers around slab APIs requiring slab.h to be added manually. 5. The script was run on all .h files but without automatically editing them as sprinkling gfp.h and slab.h inclusions around .h files could easily lead to inclusion dependency hell. Most gfp.h inclusion directives were ignored as stuff from gfp.h was usually wildly available and often used in preprocessor macros. Each slab.h inclusion directive was examined and added manually as necessary. 6. percpu.h was updated not to include slab.h. 7. Build test were done on the following configurations and failures were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my distributed build env didn't work with gcov compiles) and a few more options had to be turned off depending on archs to make things build (like ipr on powerpc/64 which failed due to missing writeq). * x86 and x86_64 UP and SMP allmodconfig and a custom test config. * powerpc and powerpc64 SMP allmodconfig * sparc and sparc64 SMP allmodconfig * ia64 SMP allmodconfig * s390 SMP allmodconfig * alpha SMP allmodconfig * um on x86_64 SMP allmodconfig 8. percpu.h modifications were reverted so that it could be applied as a separate patch and serve as bisection point. Given the fact that I had only a couple of failures from tests on step 6, I'm fairly confident about the coverage of this conversion patch. If there is a breakage, it's likely to be something in one of the arch headers which should be easily discoverable easily on most builds of the specific arch. Signed-off-by: NTejun Heo <tj@kernel.org> Guess-its-ok-by: NChristoph Lameter <cl@linux-foundation.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
-
- 22 3月, 2010 6 次提交
-
-
由 Daniel Mack 提交于
This fixes a warning when booting 2.6.34-rc2: [ 26.619814] ------------[ cut here ]------------ [ 26.624604] WARNING: at fs/proc/generic.c:316 __xlate_proc_name+0xac/0xc0() [ 26.631555] name 'on/off button' [ 26.634753] Modules linked in: Signed-off-by: NDaniel Mack <daniel@caiaq.de> Cc: Sven Neumann <s.neumann@raumfeld.com> Signed-off-by: NEric Miao <eric.y.miao@gmail.com>
-
由 Huang Weiyi 提交于
Remove duplicated #include('s) in arch/arm/mach-pxa/raumfeld.c Signed-off-by: NHuang Weiyi <weiyi.huang@gmail.com> Signed-off-by: NEric Miao <eric.y.miao@gmail.com>
-
由 Eric Miao 提交于
sharpsl_pm.c actually depends on max1111 driver being built-in when not using legacy ssp code. Reported-by: NJonathan Cameron <jic23@cam.ac.uk> Signed-off-by: NEric Miao <eric.y.miao@gmail.com>
-
由 Eric Miao 提交于
Reported-by: NJonathan Cameron <jic23@cam.ac.uk> Signed-off-by: NEric Miao <eric.y.miao@gmail.com>
-
由 Jonathan Cameron 提交于
Signed-off-by: NJonathan Cameron <jic23@cam.ac.uk> Signed-off-by: NEric Miao <eric.y.miao@gmail.com>
-
由 Jonathan Cameron 提交于
Due to commit: 5de813b6 ARM: Eliminate decompressor -Dstatic= PIC hack The data section will be discarded for the decompressor, thus move the static variables into BSS section by initializing them at run time. Signed-off-by: NJonathan Cameron <jic23@cam.ac.uk> Signed-off-by: NEric Miao <eric.y.miao@gmail.com>
-
- 13 3月, 2010 2 次提交
-
-
由 FUJITA Tomonori 提交于
This converts arm to the generic pci_set_dma_mask and pci_set_consistent_dma_mask (removes HAVE_ARCH_PCI_SET_DMA_MASK for dmabounce). Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Looked-over-by: NRussell King <rmk+kernel@arm.linux.org.uk> Cc: Jesse Barnes <jbarnes@virtuousgeek.org> Cc: Greg KH <greg@kroah.com> Cc: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Jaya Kumar 提交于
Update broadsheetfb to add support for multiple panel types. The 3.7" and 6" are known to work but the 9.7" is untested due to lack of hardware. Signed-off-by: NJaya Kumar <jayakumar.lkml@gmail.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Krzysztof Helt <krzysztof.h1@wp.pl> Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 08 3月, 2010 1 次提交
-
-
由 Uwe Kleine-König 提交于
A pointer to a probe callback is passed to the core via platform_driver_register and so the function must not disappear when the .init sections are discarded. Otherwise (if also having HOTPLUG=y) unbinding and binding a device to the driver via sysfs will result in an oops as does a device being registered late. An alternative to this patch is using platform_driver_probe instead of platform_driver_register plus removing the pointer to the probe function from the struct platform_driver. Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Ben Dooks <ben-linux@fluff.org> Cc: Dmitry Baryshkov <dbaryshkov@gmail.com> Cc: Eric Miao <eric.miao@marvell.com> Cc: Liam Girdwood <liam.girdwood@wolfsonmicro.com> Cc: Paul Sokolovsky <pmiscml@gmail.com> Cc: Richard Purdie <rpurdie@rpsys.net> Cc: Russell King <rmk+kernel@arm.linux.org.uk> Acked-by: NArnaud Patard <arnaud.patard@rtp-net.org> Acked-by: NDmitry Eremin-Solenikov <dbaryshkov@gmail.com> Acked-by: NKristoffer Ericson <kristoffer.ericson@gmail.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
- 02 3月, 2010 2 次提交
-
-
由 Eric Miao 提交于
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>
-
由 Daniel Mack 提交于
Set GPIO bits to pull the pins connected to LEDs for lower power mode. We want all LEDs off when devices are in suspend. Signed-off-by: NDaniel Mack <daniel@caiaq.de> Signed-off-by: NEric Miao <eric.y.miao@gmail.com>
-