Prevents code that assumes that the encoder is active when asked to be
disabled from dying a horrible death.
Reported-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Kristian Høgsberg <krh@bitplanet.net>
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDave Airlie <airlied@redhat.com>

As we may try to power down the link at various times, it is not
necessarily still coupled with an encoder and so we must be careful not
to depend upon an operation that is only valid when the link is still
attached to a pipe.

Fixes regression in 5bddd17f.
Reported-and-tested-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org [after applying 5bddd17f]

In order for bos to retire eventually, a request must be sent down the
ring. This is expected, for example, by occlusion queries for which mesa
will wait upon (whilst running glean) before issuing more batches and so
the normal activity upon the ring is suspended and we need to emit a
request to clear the idle ring.
Reported-by: NJinjin, Wang <jinjin.wang@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=30380Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

While looking for the duplicates in /sys/class/wmi/, I couldn't find
them. The code that looks for duplicates uses strncmp in a binary GUID,
which may contain zero bytes. The right function is memcmp, which is
also used in another section of wmi code.

It was finding 49142400-C6A3-40FA-BADB-8A2652834100 as a duplicate of
39142400-C6A3-40FA-BADB-8A2652834100. Since the first byte is the fourth
printed, they were found as equal by strncmp.
Signed-off-by: NThadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Cc: stable@kernel.org

Linus Torvalds pointed out that our code was unbalanced when powering on
the panel with respect to the power off sequence in that we were failing
to restore the panel-fitter. The consequence of this would be that
across a simple DPMS off/on for a non-native mode, without an intervening
modeset, the panel fitter would remain disabled and the output would shift
on the panel.
Reported-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

There's not much we can do here but hope for the best. However the first
failure happens quite frequently and if often remedied by the second
attempt to reset HEAD. So only print the error if that attempt also
fails.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=19802Reported-by: NThomas Meyer <thomas@m3y3r.de>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org

Otherwise we can't really fix the abi-braindeadness of forcing
libva to manually wait for rendering when switching rings. Which
in turn makes implementing hw semaphores a pointless exercise
(at least for ironlake).

[Also added the relaxed fencing param to explain the jump in
numbering - relaxed fencing is in -next.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Add a missing NULL check and fix the wrong address passed to kunmap()
in i830_cleanup().

Cc: stable@kernel.org
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
[danvet: added cc stable]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Fix kernel warnings caused by the driver name of GSC PS/2 containing '/'.

The following warnings are observed on a K410 system :

[   10.700000] name 'GSC PS/2 keyboard'
[   10.732000] ------------[ cut here ]------------
[   10.772000] WARNING: at fs/proc/generic.c:323
[   10.828000] Modules linked in:
[   10.916000]
[   10.916000]      YZrvWESTHLNXBCVMcbcbcbcbOGFRQPDI
[   10.936000] PSW: 00000000000001000000000000001111 Not tainted
[   10.992000] r00-03  0004000f 104fe3e0 10201ea0 00000000
[   11.060000] r04-07  4fc405c8 00000006 4fc405c8 4fc40694
[   11.124000] r08-11  4fc40708 10438aa0 00000001 1043bfc8
[   11.184000] r12-15  104ff2a0 104ff2a0 4fc38634 104ff2a0
[   11.248000] r16-19  f0001570 10479af0 f000006c 1044fe50
[   11.308000] r20-23  00000000 00000028 104cd858 00000000
[   11.372000] r24-27  ffffffff 0000000e 1044fe10 1043bbe0
[   11.436000] r28-31  0000002b 00000078 4fc40800 0000000d
[   11.496000] sr00-03  00000000 00000000 00000000 00000000
[   11.560000] sr04-07  00000000 00000000 00000000 00000000
[   11.624000]
[   11.688000] IASQ: 00000000 00000000 IAOQ: 10201ea0 10201ea4
[   11.704000]  IIR: 03ffe01f    ISR: 00000000  IOR: 0000000d
[   11.772000]  CPU:        0   CR30: 4fc40000 CR31: f01043b0
[   11.836000]  ORIG_R28: 4fc40940
[   11.904000]  IAOQ[0]: __xlate_proc_name+0x90/0xd0
[   11.940000]  IAOQ[1]: __xlate_proc_name+0x94/0xd0
[   11.996000]  RP(r2): __xlate_proc_name+0x90/0xd0
[   12.052000] Backtrace:
[   12.108000]  [<10257790>] vsnprintf+0x290/0x4f4
[   12.136000]
[   12.188000] ---[ end trace 91bf6ece17e322dd ]---
[   12.208000] serio: GSC PS/2 keyboard port at 0x0001c000 irq 19 @ 10:12:7
[   12.264000] name 'GSC PS/2 mouse'
[   12.344000] ------------[ cut here ]------------
[   12.384000] WARNING: at fs/proc/generic.c:323
[   12.436000] Modules linked in:
[   12.524000]
[   12.528000]      YZrvWESTHLNXBCVMcbcbcbcbOGFRQPDI
[   12.544000] PSW: 00000000000001000000000000001111 Tainted: G        W
[   12.600000] r00-03  0004000f 104fe3e0 10201ea0 00000000
[   12.680000] r04-07  4fc405c8 00000006 4fc405c8 4fc40694
[   12.740000] r08-11  4fc40708 10438aa0 00000001 1043bfc8
[   12.804000] r12-15  104ff2a0 104ff2a0 4fc38634 104ff2a0
[   12.868000] r16-19  f0001570 10479af0 f000006c 1044fe50
[   12.928000] r20-23  00000000 00000025 104cd858 00000000
[   12.992000] r24-27  ffffffff 0000000e 1044fe10 1043bbe0
[   13.056000] r28-31  00000028 00000078 4fc40800 0000000d
[   13.116000] sr00-03  00000000 00000000 00000000 00000000
[   13.180000] sr04-07  00000000 00000000 00000000 00000000
[   13.244000]
[   13.308000] IASQ: 00000000 00000000 IAOQ: 10201ea0 10201ea4
[   13.324000]  IIR: 03ffe01f    ISR: 00000000  IOR: 0000000d
[   13.392000]  CPU:        0   CR30: 4fc40000 CR31: f01043b0
[   13.456000]  ORIG_R28: 4fc40940
[   13.524000]  IAOQ[0]: __xlate_proc_name+0x90/0xd0
[   13.560000]  IAOQ[1]: __xlate_proc_name+0x94/0xd0
[   13.616000]  RP(r2): __xlate_proc_name+0x90/0xd0
[   13.672000] Backtrace:
[   13.728000]  [<10257790>] vsnprintf+0x290/0x4f4
[   13.756000]
[   13.808000] ---[ end trace 91bf6ece17e322de ]---
[   13.828000] serio: GSC PS/2 mouse port at 0x00020100 irq 19 @ 10:12:8
Signed-off-by: NGuy Martin <gmsoft@tuxicoman.be>
Acked-by: NHelge Deller <deller@gmx.de>
Signed-off-by: NKyle McMartin <kyle@mcmartin.ca>

K class aka KittyHawk don't have LED support on their LCD. Installing
HP-UX confirmed this. The current led_wq fills the LCD with black
characters each time it runs.

The patch prevents the led_wq workqueue and its proc entry to be
created for KittyHawk machines.

It also increase min_cmd_delay as currently, one character out of two
is lost when a string is sent to the LCD.
Signed-off-by: NGuy Martin <gmsoft@tuxicoman.be>
Signed-off-by: NKyle McMartin <kyle@mcmartin.c>

The generic conversion eliminates the spurious no_ack and no_end
routines, converts all the cascaded handlers to handle_simple_irq() and
makes iosapic use a modified handle_percpu_irq() to become the same as
the CPU irq's.  This isn't an essential change, but it eliminates the
mask/unmask overhead of handle_level_irq().
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>
Tested-by: NHelge Deller <deller@gmx.de>
Signed-off-by: NKyle McMartin <kyle@mcmartin.ca>

Fixes the modesetting on the secondary panel of the Libretto W100 and
presumably many more Ironlake laptops with SDVO LVDS displays.
Reported-and-tested-by: NMatthew Willoughby <mattfredwill@gmail.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org

This patch fixes a compilation issue when compiling PCMCIA SA1100
support as a module with PCMCIA_DEBUG enabled. The symbol
soc_pcmcia_debug was not beeing exported.
ARM: pcmcia: Fix for building DEBUG with sa11xx_base.c as a module.

This patch fixes a compilation issue when compiling PCMCIA SA1100
support as a module with PCMCIA_DEBUG enabled. The symbol
soc_pcmcia_debug was not beeing exported.

Cc: <stable@kernel.org>
Signed-off-by: NMarcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Use the hardware DDA to calculate the ratio with as much accuracy as is
possible.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org

If we leave the registers in a conflicting state then when we attempt
to teardown the active mode, we will not disable the pipes and planes
in the correct order -- leaving a plane reading from a disabled pipe and
possibly leading to undefined behaviour.
Reported-and-tested-by: NAndy Whitcroft <apw@canonical.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=32078Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org

My new shiny code for corrupted PEB detection has NOR specific bug.
We tread PEB as corrupted and preserve it, if

1. EC header is OK.
2. VID header is corrupted.
3. data area is not "all 0xFFs"

In case of NOR we have 'nor_erase_prepare()' quirk, which invalidates
the headers before erasing the PEB. And we invalidate first the VID
header, and then the EC header. So if a power cut happens after we have
invalidated the VID header, but before we have invalidated the EC
header, we end up with a PEB which satisfies the above 3 conditions,
and the scanning code will treat it as corrupted, and will print
scary warnings, wrongly.

This patch fixes the issue by firt invalidating the EC header, then
invalidating the VID header. In case of power cut inbetween, we still
just lose the EC header, and UBI can deal with this situation gracefully.

Thanks to Anatolij Gustschin <agust@denx.de> for tracking this down.
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Reported-by: NAnatolij Gustschin <agust@denx.de>
Tested-by: NAnatolij Gustschin <agust@denx.de>

Allocate irq descs on any NUMA node (we don't care) rather than
specifically node 0, which may not exist.

(At the moment NUMA is meaningless within a domain, so any info
the kernel has is just from an SRAT table we haven't suppressed/disabled.)
Signed-off-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>

If this is a non-HIGHMEM 32-bit kernel, then the page structures only go
up to the limit of addressable memory, even if more memory is physically
present.  Don't try to add that extra memory to the balloon.
Signed-off-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>

The AMD Geode CS5536 Companion Device Silicon Revision B1 Specification
Update mentions the follow as issue #36:

 "Atomic write transactions to the atomic GPIO High Bank Feature Bit
  registers should only affect the bits selected [...]"

 "after Suspend, an atomic write transaction [...] will clear all
  non-selected bits of the accessed register."

In other words, writing to the high bank for a single GPIO bit will
clear every other GPIO bit (but only sometimes after a suspend).

The workaround described is obvious and simple; do a read-modify-write.
This patch does that, and documents why we're doing it.
Signed-off-by: NAndres Salomon <dilinger@queued.net>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

It's not useful to build LED triggers when there's no LEDs that can be
triggered by them.  Therefore, fix up the dependencies so that this
cannot happen, and fix a few users that select triggers to depend on
LEDS_CLASS as well (there is also one user that also selects LEDS_CLASS,
which is OK).
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Reported-by: NRandy Dunlap <randy.dunlap@oracle.com>
Acked-by: NRandy Dunlap <randy.dunlap@oracle.com>
Tested-by: NIngo Molnar <mingo@elte.hu>
Cc: Arnd Hannemann <arnd@arndnet.de>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Richard Purdie <rpurdie@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This workaround only applies to Ironlake.
Signed-off-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org

The pipe is always set to 8BPC, but here we were leaving whatever
previous bits were set by the BIOS in place.
Signed-off-by: NEric Anholt <eric@anholt.net>
Tested-by: NKeith Packard <keithp@keithp.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org

Re-map and re-bind all the pirqs at resume time.
Signed-off-by: NStefano Stabellini <stefano.stabellini@eu.citrix.com>

Signed-off-by: NStefano Stabellini <stefano.stabellini@eu.citrix.com>

When remapping MSIs into pirqs for PV on HVM guests, qemu is responsible
for doing the actual mapping and unmapping.
We only give qemu the desired pirq number when we ask to do the mapping
the first time, after that we should be reading back the pirq number
from qemu every time we want to re-enable the MSI.

This fixes a bug in xen_hvm_setup_msi_irqs that manifests itself when
trying to enable the same MSI for the second time: the old MSI to pirq
mapping is still valid at this point but xen_hvm_setup_msi_irqs would
try to assign a new pirq anyway.
A simple way to reproduce this bug is to assign an MSI capable network
card to a PV on HVM guest, if the user brings down the corresponding
ethernet interface and up again, Linux would fail to enable MSIs on the
device.
Signed-off-by: NStefano Stabellini <stefano.stabellini@eu.citrix.com>

Use the new hypercall PHYSDEVOP_get_free_pirq to ask Xen to allocate a
pirq. Remove the unsupported PHYSDEVOP_get_nr_pirqs hypercall to get the
amount of pirq available.

This fixes find_unbound_pirq that otherwise would return a number
starting from nr_irqs that might very well be out of range in Xen.

The symptom of this bug is that when you passthrough an MSI capable pci
device to a PV on HVM guest, Linux would fail to enable MSIs on the
device.
Signed-off-by: NStefano Stabellini <stefano.stabellini@eu.citrix.com>

On some motherboards the it8712f watchdog does not work unless
the game port was enabled. see Bug 13140. We therefor add a note
to Kconfig.
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Add missing include "linux/fs.h".
This fixes compile failure.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NMartyn Welch <martyn.welch@ge.com>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

* fix devinit and devexit sections
* fix platform removal code so that the iounmap happens after the removal of the timer.
* changes the reboot_notifier by a platform shutdown method.
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

This patch adds an additional LPC Controller DeviceID for the Intel Patsburg PCH for TCO Watchdog.
Signed-off-by: NSeth Heasley <seth.heasley@intel.com>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

Input ABI requires reporting resolution on main axes in units per
millimeter, not units per inch, so we need to convert accordingly.
Tested-by: NNikolai Kondrashov <spbnick@gmail.com>
Acked-by: NNikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

ib_ucm_init_qp_attr() and ucma_init_qp_attr() pass struct ib_uverbs_qp_attr
with reserved, qp_state, {ah_attr,alt_ah_attr}{reserved,->grh.reserved}
fields uninitialized to copy_to_user().  This leads to leaking of
contents of kernel stack memory to userspace.
Signed-off-by: NVasiliy Kulikov <segoon@openwall.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Remove unused functions added by commit ff7f5aab ("IB/pack: IBoE UD
packet packing support").
Signed-off-by: NOr Gerlitz <ogerlitz@voltaire.com>

Use netif_running() and netif_carrier_ok() to report link state,
exactly as is done to report Ethernet link state in sysfs.
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The link rate is the product of the link speed in the link width. For
Etherent ports the rate is 10G, so we use 1 for the width and 4 for
speed to get the correct rate.
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

ConnectX firmware is supposed to report the number blue flame
registers per page as log2 of the value.  However, due to a firmware
bug, it reports actual number.  This patch works around this by
checking if the number of registers calculated fits within a page.  If
it does not, we use 8 registers per page.
Signed-off-by: NEli Cohen <eli@mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The new interface creates directories per mapped image
and under each it creates a subdir per available snapshot.
This allows keeping a cleaner interface within the sysfs
guidelines. The ABI documentation was updated too.
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NYehuda Sadeh <yehuda@hq.newdream.net>
Signed-off-by: NSage Weil <sage@newdream.net>

We must fully update the control segment before marking it as valid,
so that hardware doesn't start executing it before we're ready.
Signed-off-by: NEli Cohen <eli@mellanox.co.il>

[ Move VLAN control bit setting to before wmb().  - Roland ]
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The Geode X driver uses both of the LX's palettes, one for gamma
correction and one for colormaps.

The kernel driver currently only backs up the one used for colormaps
during suspend/resume. If you mess with gamma settings and do a
suspend/resume, colors go funny.

Fix this by backing up the video proc palette during suspend/resume,
alongside the display controller one which is already handled.
Signed-off-by: NDaniel Drake <dsd@laptop.org>
Acked-by: NAndres Salomon <dilinger@queued.net>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>