Support for the at91sam9g20 : Atmel 400Mhz ARM 926ej-s SOC.

AT91sam9g20 is an evolution of the at91sam9260 with a faster clock
speed.
We created a new board for this device but based the chip support
directly on 9260 files with little updates.
Here is the chip page on Atmel wabsite:
http://atmel.com/dyn/products/product_card.asp?part_id=4337Signed-off-by: NSedji Gaouaou <sedji.gaouaou@atmel.com>
Signed-off-by: NJustin Waters <justin.waters@timesys.com>
Acked-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The pxa2xx_udc.c driver is renamed to pxa25x_udc.c (the platform
driver name changes from pxa2xx-udc to pxa25x-udc) and the
platform driver name of pxa27x_udc.c is fixed to pxa27x-udc.
pxa_device_udc in devices.c is split into pxa25x and pxa27x flavors
and the pxa27x_device_udc is enabled in pxa27x.c.
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Acked-by: NNicolas Pitre <nico@cam.org>
Acked-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Including from Ian Molton:

Fixes for mistakes left over from the PXA2{5,7}X UDC split.
Signed-off-by: NIan Molton <spyro@f2s.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

	is handled in board code
Signed-off-by: NDmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NDmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Both i2c-pxa.c and irq.c still include pxa2xx-gpio.h although is is not
needed anymore.
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Acked-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch adds exit and remove handlers to pxafb so that it can be loaded
and unloaded as a module.
Signed-off-by: NJaya Kumar <jayakumar.lkml@gmail.com>
Acked-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Acked-by: NEric Miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

add support for mx2 in i.MX serial driver
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This patch adds MX3 support for the i.MX internal uart driver.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This patch introduces the clock API for i.MX and converts all
in-Kernel drivers to use it.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This patch removes the statically initialized tables from the i.MX serial
driver and makes the driver fully dependent on the information provided by
the platform_device.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Add platform specific init functions. Also rename the struct
platform_device dev into pdev.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

We assumed a 16MHz reference frequency for the UART. While this
is true for i.MX1 most of the time it is not true for MX27/MX31.
Also, add handling for the ONEMS register which is present on
newer versions of the chip and pass a sane minimum baudrate to
uart_get_baud_rate().
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

The reason for forcing a number of ports should be documented.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fixes bugzilla.kernel.org #10868
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

As reported by Ken A Scott <kscott9@sent.com>

Cc: Ken A Scott <kscott9@sent.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Thanks to umesh b <umesh.kollam@gmail.com> for the information here.

Cc: umesh b <umesh.kollam@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1111) fixes a bug in the hub driver.  When a hub
resumes, disconnections that occurred while the hub was suspended are
lost.

A completely different fix for this problem has already been accepted
for 2.6.27; however the problem still needs to be handled in 2.6.26.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Tested-by: NLukas Hejtmanek <xhejtman@ics.muni.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

USB: fix interrupt disabling for HCDs with shared interrupt handlers

As has been discussed several times on LKML, IRQF_SHARED | IRQF_DISABLED
doesn't work reliably, i.e. a shared interrupt handler CAN'T be certain to
be called with interrupts disabled. Most USB HCD handlers use IRQF_DISABLED
and therefore havoc can break out if they share their interrupt with a
handler that doesn't use it.

On my test machine the yenta_socket interrupt handler (no IRQF_DISABLED)
was registered before ehci_hcd and one uhci_hcd instance. Therefore all
usb_hcd_irq() invocations for ehci_hcd and for one uhci_hcd instance
happened with interrupts enabled. That led to random lockups as USB core
HCD functions that acquire the same spinlock could be called twice
from interrupt handlers.

This patch updates usb_hcd_irq() to always disable/restore interrupts.
usb_add_hcd() will silently remove any IRQF_DISABLED requested from HCD code.
Signed-off-by: NStefan Becker <stefan.becker@nokia.com>
Cc: stable <stable@kernel.org>
Acked-by: NDavid Brownell <david-b@pacbell.net>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Here's a new device ID for the ftdio_sio driver.
The diff is with linus's tree as of this morning.

The device is the RigExpert Tiny USB Soundcard Transceiver Interface for ham
radio.

(I didn't actually test this. A fellow ham couldn't get the device to work, and
I suggested binding the device ID using sysfs - see
"http://jk.ufisa.uninett.no/usb/". However, he had had moved on to other things
by then. I guess adding the device ID to the kernel "on spec" won't hurt.
The relevant part of cat /proc/bus/usb/devices shows:

T:  Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=12  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs=  1
P:  Vendor=0403 ProdID=ed22 Rev= 5.00
S:  Manufacturer=FTDI
S:  Product=MixW RigExpert Tiny
S:  SerialNumber=00000000
C:* #Ifs= 2 Cfg#= 1 Atr=80 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=81(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=83(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
)

From: Jon K Hellan <hellan@acm.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Remove dev_info call on disconnect. The sisusb_dev pointer may have been
set to zero by sisusb_delete at this point causing an oops.

The message does not provide any extra information over the standard USB
subsystem output so removing it does not affect functionality.
Signed-off-by: NWill Newton <will.newton@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

CY7C68310 chip also support cypress atacb "ATA command" pass_thru.
Signed-off-by: NMatthieu CASTET <castet.matthieu@free.fr>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fixes a problem with OHCI where canceling bulk or
interrupt URBs may lose track of the right data toggle.  This
seems to be a longstanding bug, possibly dating back to the
Linux 2.4 kernel, which stayed hidden because

 (a) about half the time the data toggle bit was correct;
 (b) canceling such URBs is unusual; and
 (c) the few drivers which cancel these URBs either
      [1] do it only as part of shutting down, or
      [2] have fault recovery logic, which recovers.

For those transfer types, the toggle is normally written back
into the ED when each TD is retired.  But canceling bypasses
the mechanism used to retire TDs ... so on average, half the
time the toggle bit will be invalid after cancelation.

The fix is simple:  the toggle state of any canceled TDs are
propagated back to the ED in the finish_unlinks function.

(Issue found by leonidv11@gmail.com ...)
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Leonid <leonidv11@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fixes a regression in the EHCI driver's TIMER_IO_WATCHDOG
behavior.  The patch "USB: EHCI: add separate IAA watchdog timer" changed
how that timer is handled, so that short timeouts on the remaining
timer (unfortunately, overloaded) would never be used.

This takes a more direct approach, reorganizing the code slightly to
be explicit about only the I/O watchdog role now being overridable.
It also replaces a now-obsolete comment describing older timer behavior.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Leonid <leonidv11@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

cdc-acm has
- a memory leak in resume()
- will fail to reactivate the read code path if this is needed.
his corrects it by deleting the useless relict code.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

If the SM501 and another platform driver, such as the SM501
then we end up defining PLATFORM_DRIVER twice. This patch
seperated the SM501 onto a seperate define of SM501_OHCI_DRIVER
so that it can be selected without overwriting the original
definition.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The S3C2410 serial driver in drivers/serial/s3c2410.c has been
growing bigger with the addition of more variants of this hardware
with the growing Samsung SoCs range. As such, it would be
easier to split this code up into a core and per-cpu drivers to
make driver addition easier, and the core smaller.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add attribute to show the current clock source for the serial
driver and remove old and annoying debug output.

Note, this only currently shows the current source with a
"* " prefix to indicate that it is the current source. Future
code will list all the clock sources, with the non-selected
one with "  " prefix.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
PATCH FOLLOWS
KernelVersion: 2.6.26-rc3

imx_dma_request_by_prio can return channel number by itself.
No need to supply variable address through parameters.

Also converted all drivers using this function.
Signed-off-by: NPaulius Zaleckas <paulius.zaleckas@teltonika.lt>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The config option for building drivers/acorn/char/defkeymap-l7200.c is
not present since at least kernel 2.6.0.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The original driver had an MODULE_LICENSE statement for GPL,
but no explict license in the header of the file. To make
this more explicit, and since I am the original authour,
we will add a GPLv2 header.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Remove the changelog which should really be found
in the version control system.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Update acornscsi as per all the other ecard drivers to use MMIO
accessors rather than the obsolete 'pc io' style inb/outb accessors.

Use ecard_request_resources()/ecard_release_resources() for easier
resource handling, rather than requesting 5 separate regions
individually.
Acked-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The kernel has its own, so let's use that instead.
Acked-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Acked-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Revive the AcornSCSI driver, update it for the replacement command
abort and host reset methods, and fix the build errors in
acornscsi-io.S.
Acked-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Acked-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Fix:
  drivers/net/arm/etherh.c:650: warning: unused variable `i'
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Make the return of pwm_request() be more informative than just
being NULL on error by using PTR_ERR() to respond with an
approriate error.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This allows platform code to manipulate GPIOs and brightness level as
needed.
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch mostly from Eric Miao, with minor edits by rmk to convert
Eric's driver to a generic PWM-based backlight driver.
Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>