- 18 5月, 2010 14 次提交
-
-
由 Michael Hennerich 提交于
Note that WOL works only in PM Suspend Standby Mode (Sleep Mode). Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com> Signed-off-by: NMike Frysinger <vapier@gentoo.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Sonic Zhang 提交于
Otherwise we might be get a setting mismatch from a previous module or bootloader and what the driver currently expects. Signed-off-by: NSonic Zhang <sonic.zhang@analog.com> Signed-off-by: NMike Frysinger <vapier@gentoo.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Sonic Zhang 提交于
IP checksum is based on 16-bit one's complement algorithm, so to deduce a value from checksum is equal to add its complement. Unfortunately, the Blackfin on-chip MAC checksum logic only works when the IP packet has a header length of 20 bytes. This is true for most IPv4 packets, but not for IPv6 packets or IPv4 packets which use header options. So only use the hardware checksum when appropriate. Signed-off-by: NSonic Zhang <sonic.zhang@analog.com> Signed-off-by: NJon Kowal <jon.kowal@dspecialists.de> Signed-off-by: NMike Frysinger <vapier@gentoo.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Sonic Zhang 提交于
The skb buffer isn't actually used until we finish transferring and pass it up to higher layers, so only invalidate the range once before we start receiving actual data. This also avoids the problem with data invalidating on Blackfin systems -- there is no invalidate-only, just invalidate+flush. So when running in writeback mode, there is the small (but not uncommon) possibility of the flush overwriting valid DMA-ed data from the cache. Signed-off-by: NSonic Zhang <sonic.zhang@analog.com> Signed-off-by: NMike Frysinger <vapier@gentoo.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Peter Meerwald 提交于
Signed-off-by: NPeter Meerwald <pmeerw@pmeerw.net> Signed-off-by: NGraf Yang <graf.yang@analog.com> Signed-off-by: NMike Frysinger <vapier@gentoo.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Barry Song 提交于
Newer on-chip MAC peripherals support IEEE 1588 PTP in the hardware, so extend the driver to support this functionality. Signed-off-by: NBarry Song <barry.song@analog.com> Signed-off-by: NMike Frysinger <vapier@gentoo.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
TCP outgoing packets can avoid two atomic ops, and dirtying of previously higly contended cache line using new refdst infrastructure. Note 1: loopback device excluded because of !IFF_XMIT_DST_RELEASE Note 2: UDP packets dsts are built before ip_queue_xmit(). Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
Use ip_route_input_noref() in ip fast path, to avoid two atomic ops per incoming packet. Note: loopback is excluded from this optimization in ip_rcv_finish() Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
ip_route_input() is the version returning a refcounted dst, while ip_route_input_noref() returns a non refcounted one. Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
Use low order bit of skb->_skb_dst to tell dst is not refcounted. Change _skb_dst to _skb_refdst to make sure all uses are catched. skb_dst() returns the dst, regardless of noref bit set or not, but with a lockdep check to make sure a noref dst is not given if current user is not rcu protected. New skb_dst_set_noref() helper to set an notrefcounted dst on a skb. (with lockdep check) skb_dst_drop() drops a reference only if skb dst was refcounted. skb_dst_force() helper is used to force a refcount on dst, when skb is queued and not anymore RCU protected. Use skb_dst_force() in __sk_add_backlog(), __dev_xmit_skb() if !IFF_XMIT_DST_RELEASE or skb enqueued on qdisc queue, in sock_queue_rcv_skb(), in __nf_queue(). Use skb_dst_force() in dev_requeue_skb(). Note: dst_use_noref() still dirties dst, we might transform it later to do one dirtying per jiffies. Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
If CONFIG_SMP=y, then we own a queue spinlock, we can avoid the atomic test_and_set_bit() from napi_schedule_prep(). We now have same number of atomic ops per netif_rx() calls than with pre-RPS kernel. Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Neil Jones 提交于
Using this driver can cause unaligned accesses in the IP layer This has been fixed by aligning the skb data correctly using the spare room left over by the 4 byte header inserted between packets by the device. Signed-off-by: NNeil Jones <NeilJay@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Brian King 提交于
Adds support for resuming from suspend for IBM virtual ethernet devices. We may have lost an interrupt over the suspend, so we just kick the interrupt handler to process anything that is outstanding. Signed-off-by: NBrian King <brking@linux.vnet.ibm.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Florian Westphal 提交于
as addrlabels with an interface index are left alone when the interface gets removed this results in addrlabels that can no longer be removed. Restrict validation of index to adding new addrlabels. Signed-off-by: NFlorian Westphal <fw@strlen.de> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 17 5月, 2010 1 次提交
-
-
由 David S. Miller 提交于
Conflicts: include/linux/if_link.h
-
- 16 5月, 2010 20 次提交
-
-
由 Chris Wright 提交于
Now we have a set of nested attributes: IFLA_VFINFO_LIST (NESTED) IFLA_VF_INFO (NESTED) IFLA_VF_MAC IFLA_VF_VLAN IFLA_VF_TX_RATE This allows a single set to operate on multiple attributes if desired. Among other things, it means a dump can be replayed to set state. The current interface has yet to be released, so this seems like something to consider for 2.6.34. Signed-off-by: NChris Wright <chrisw@sous-sol.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Frank Blaschka 提交于
Synchronize access to the drivers configuration interface. Also do not allow configuration changes during online/offline transition. Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ursula Braun 提交于
z/OS may activate Optimized Latency Mode (OLM) for a connection through an OSA Express3 adapter, which reduces the number of allowed concurrent connections, if adapter is used in shared mode. Create a meaningful message, if activation of an OSA-connection fails due to an active OLM-connection on the shared OSA-adapter. Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com> Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Frank Blaschka 提交于
OSA supports HW TX checksumming in layer 3 mode. Enable this feature and remove software fallback used for TSO. Cleanup checksum bits to indicate OSA can do checksumming only for IPv4 TCP and UDP. Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Wei Yongjun 提交于
transport may be free before ICMP proto unreachable timer expire, so we should delete active ICMP proto unreachable timer when transport is going away. Signed-off-by: NWei Yongjun <yjwei@cn.fujitsu.com> Acked-by: NVlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
vlan/macvlan start_xmit() can inform caller of congestion with NET_XMIT_CN return value. This doesnt mean packet was dropped. Increment normal stat counters instead of tx_dropped. Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> Acked-by: NPatrick McHardy <kaber@trash.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
TCP-MD5 sessions have intermittent failures, when route cache is invalidated. ip_queue_xmit() has to find a new route, calls sk_setup_caps(sk, &rt->u.dst), destroying the sk->sk_route_caps &= ~NETIF_F_GSO_MASK that MD5 desperately try to make all over its way (from tcp_transmit_skb() for example) So we send few bad packets, and everything is fine when tcp_transmit_skb() is called again for this socket. Since ip_queue_xmit() is at a lower level than TCP-MD5, I chose to use a socket field, sk_route_nocaps, containing bits to mask on sk_route_caps. Reported-by: NBhaskar Dutta <bhaskie@gmail.com> Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
TCP MD5 support uses percpu data for temporary storage. It currently disables preemption so that same storage cannot be reclaimed by another thread on same cpu. We also have to make sure a softirq handler wont try to use also same context. Various bug reports demonstrated corruptions. Fix is to disable preemption and BH. Reported-by: NBhaskar Dutta <bhaskie@gmail.com> Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
With RPS inclusion, skb timestamping is not consistent in RX path. If netif_receive_skb() is used, its deferred after RPS dispatch. If netif_rx() is used, its done before RPS dispatch. This can give strange tcpdump timestamps results. I think timestamping should be done as soon as possible in the receive path, to get meaningful values (ie timestamps taken at the time packet was delivered by NIC driver to our stack), even if NAPI already can defer timestamping a bit (RPS can help to reduce the gap) Tom Herbert prefer to sample timestamps after RPS dispatch. In case sampling is expensive (HPET/acpi_pm on x86), this makes sense. Let admins switch from one mode to another, using a new sysctl, /proc/sys/net/core/netdev_tstamp_prequeue Its default value (1), means timestamps are taken as soon as possible, before backlog queueing, giving accurate timestamps. Setting a 0 value permits to sample timestamps when processing backlog, after RPS dispatch, to lower the load of the pre-RPS cpu. Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Timo Teras 提交于
I mistakenly had the error path to use num_pols to decide how many policies we need to drop (cruft from earlier patch set version which did not handle socket policies right). This is wrong since normally we do not keep explicit references (instead we hold reference to the cache entry which holds references to policies). drop_pols is set to num_pols if we are holding the references, so use that. Otherwise we eventually BUG_ON inside xfrm_policy_destroy due to premature policy deletion. Signed-off-by: NTimo Teras <timo.teras@iki.fi> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jiri Pirko 提交于
Now there's null check here and also again in the hook. Looking at bridge bits which are simmilar, port structure is rcu_dereferenced right away in handle_bridge and passed to hook. Looks nicer. Signed-off-by: NJiri Pirko <jpirko@redhat.com> Acked-by: NPatrick McHardy <kaber@trash.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 FUJITA Tomonori 提交于
This replace the PCI DMA state API (include/linux/pci-dma.h) with the DMA equivalents since the PCI DMA state API will be obsolete. No functional change. For further information about the background: http://marc.info/?l=linux-netdev&m=127037540020276&w=2Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Acked-by: NStephen Hemminger <shemminger@vyatta.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Amerigo Wang 提交于
(Dropped the infiniband part, because Tetsuo modified the related code, I will send a separate patch for it once this is accepted.) This patch introduces /proc/sys/net/ipv4/ip_local_reserved_ports which allows users to reserve ports for third-party applications. The reserved ports will not be used by automatic port assignments (e.g. when calling connect() or bind() with port number 0). Explicit port allocation behavior is unchanged. Signed-off-by: NOctavian Purdila <opurdila@ixiacom.com> Signed-off-by: NWANG Cong <amwang@redhat.com> Cc: Neil Horman <nhorman@tuxdriver.com> Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Octavian Purdila 提交于
The new function can be used to read/write large bitmaps via /proc. A comma separated range format is used for compact output and input (e.g. 1,3-4,10-10). Writing into the file will first reset the bitmap then update it based on the given input. Signed-off-by: NOctavian Purdila <opurdila@ixiacom.com> Signed-off-by: NWANG Cong <amwang@redhat.com> Cc: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Amerigo Wang 提交于
(Based on Octavian's work, and I modified a lot.) As we are about to add another integer handling proc function a little bit of cleanup is in order: add a few helper functions to improve code readability and decrease code duplication. In the process a bug is also fixed: if the user specifies a number with more then 20 digits it will be interpreted as two integers (e.g. 10000...13 will be interpreted as 100.... and 13). Behavior for EFAULT handling was changed as well. Previous to this patch, when an EFAULT error occurred in the middle of a write operation, although some of the elements were set, that was not acknowledged to the user (by shorting the write and returning the number of bytes accepted). EFAULT is now treated just like any other errors by acknowledging the amount of bytes accepted. Signed-off-by: NOctavian Purdila <opurdila@ixiacom.com> Signed-off-by: NWANG Cong <amwang@redhat.com> Cc: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Simon Arlott 提交于
Links for each port are created in sysfs using the device name, but this could be changed after being added to the bridge. As well as being unable to remove interfaces after this occurs (because userspace tools don't recognise the new name, and the kernel won't recognise the old name), adding another interface with the old name to the bridge will cause an error trying to create the sysfs link. This fixes the problem by listening for NETDEV_CHANGENAME notifications and renaming the link. https://bugzilla.kernel.org/show_bug.cgi?id=12743Signed-off-by: NSimon Arlott <simon@fire.lp0.eu> Acked-by: NStephen Hemminger <shemminger@vyatta.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 stephen hemminger 提交于
Use one set of macro's for all bridge messages. Note: can't use netdev_XXX macro's because bridge is purely virtual and has no device parent. Signed-off-by: NStephen Hemminger <shemminger@vyatta.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 stephen hemminger 提交于
Move code around so that the ifdef for NETPOLL_CONTROLLER don't have to show up in main code path. The control functions should be in helpers that are only compiled if needed. Signed-off-by: NStephen Hemminger <shemminger@vyatta.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ben Hutchings 提交于
Some RNDIS devices don't respond on the control channel until polled on the status channel. In particular, this was reported to be the case for the 2Wire HomePortal 1000SW. This is roughly based on a patch by John Carr <john.carr@unrouted.co.uk> which is reported to be needed for use with some Windows Mobile devices and which is currently applied by Mandriva. Reported-by: NMark Glassberg <vzeeaxwl@myfairpoint.net> Signed-off-by: NBen Hutchings <ben@decadent.org.uk> Tested-by: NMark Glassberg <vzeeaxwl@myfairpoint.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 15 5月, 2010 1 次提交
-
-
由 Randy Dunlap 提交于
Fix xt_TEE build for the case of NF_CONNTRACK=m and NETFILTER_XT_TARGET_TEE=y: xt_TEE.c:(.text+0x6df5c): undefined reference to `nf_conntrack_untracked' 4x Built with all 4 m/y combinations. Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com> Acked-by: NPatrick McHardy <kaber@trash.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 14 5月, 2010 4 次提交
-
-
由 Sucheta Chakraborty 提交于
When ever driver changes the device state, it should write pci-func number and timestamp in debug registers. Signed-off-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com> Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Sucheta Chakraborty 提交于
Device can go to quiescent state, during which drivers should refrain from using the device. Signed-off-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com> Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Sucheta Chakraborty 提交于
pci-func class can be other than ethernet in Qlogic CNA device. Signed-off-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com> Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>