The attached patch rate limits "WEP decrypt failed (ICV)" to avoid
flooding the logfiles.
Signed-off-by: NAdel Gadllah <adel.gadllah@gmx.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

rfkill_toggle_radio is called from functions where
rfkill->mutex is already aquired.

Remove the lock from rfkill_toggle_radio() and add it to
the only calling function that calls it without the lock held.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes a regression I (most likely) introduced, namely that
unencrypted frames are right now accepted even if we have a key for that
specific sender. That has very bad security implications.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes:
- Incorrect calls to ieee80211_hw_config when the radiotap flag is set.
- Failure to actually unset the radiotap flag when all monitors are down.
- Failure to call ieee80211_hw_config after successful interface start.
Signed-off-by: NMichael Wu <flamingice@sourmilk.net>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There is no guarantee that data+SNAP_SIZE will reside on an even numbered
address, so doing a 16 bit read will cause an unaligned access in some
situations. Based on a patch from Jun Sun.
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

I'm not sure if this is best choice, someone might have better
solutions. But this patch fixed the connection problem when switching
from a WPA enabled AP (using wpa_supplicant) to an open AP (using
iwconfig). The root cause is when we connect to a WPA enabled AP,
wpa_supplicant sets the ifsta->extra_ie thru SIOCSIWGENIE. But if we
stop wpa_supplicant and connect to an open AP with iwconfig, there is
no way to clear the extra_ie so that mac80211 keeps connecting with that.

Someone could argue wpa_supplicant should clear the extra_ie during
its shutdown. But mac80211 should also handle the unexpected shutdown
case (ie. killall -9 wpa_supplicant).

On Wed, 2007-11-21 at 16:19 +0100, Johannes Berg wrote:
> Yeah. Can you amend the patch to also clear the
> IEEE80211_STA_PRIVACY_INVOKED flag?
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/selinux-2.6:
  SELinux: return EOPNOTSUPP not ENOTSUPP

* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
  [ARM] 4638/1: pxa: use PXA3xx specific macros to define clks
  [ARM] remove useless setting of VM_RESERVED

* master.kernel.org:/pub/scm/linux/kernel/git/davej/cpufreq:
  [CPUFREQ] Fix up whitespace in conservative governor.
  [CPUFREQ] Make cpufreq_conservative handle out-of-sync events properly
  [CPUFREQ] architectural pstate driver for powernow-k8

ENOTSUPP is not a valid error code in the kernel (it is defined in some
NFS internal error codes and has been improperly used other places).  In
the !CONFIG_SECURITY_SELINUX case though it is possible that we could
return this from selinux_audit_rule_init().  This patch just returns the
userspace valid EOPNOTSUPP.
Signed-off-by: NEric Paris <eparis@redhat.com>
Signed-off-by: NJames Morris <jmorris@namei.org>

PXA3xx uses its own clk_pxa3xx_cken_ops, modify the code to use the
PXA3xx specific macros to define its clocks
Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This code harks back to the days when we didn't count dirty mapped
pages, which led us to try to balance the number of dirty unmapped pages
by how much unmapped memory there was in the system.

That makes no sense any more, since now the dirty counts include the
mapped pages.  Not to mention that the math doesn't work with HIGHMEM
machines anyway, and causes the unmapped_ratio to potentially turn
negative (which we do catch thanks to clamping it at a minimum value,
but I mention that as an indication of how broken the code is).

The code also was written at a time when the default dirty ratio was
much larger, and the unmapped_ratio logic effectively capped that large
dirty ratio a bit.  Again, we've since lowered the dirty ratio rather
aggressively, further lessening the point of that code.
Acked-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
  [NETFILTER]: Fix NULL pointer dereference in nf_nat_move_storage()
  [SUNHME]: VLAN support for sunhme
  [CHELSIO]: Fix skb->dev setting.
  [NETFILTER]: fix compat_nf_sockopt typo
  [INET]: Fix potential kfree on vmalloc-ed area of request_sock_queue
  [VIA_VELOCITY]: Don't oops on MTU change.
  iwl4965: fix not correctly dealing with hotunplug
  rt2x00: Fix chipset revision validation
  iwl3945: place CCK rates in front of OFDM for supported rates
  mac80211: Fix queuing of scan containing a SSID

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  [MIPS] N32 needs to use the compat version of sys_nfsservctl.
  [MIPS] irq_cpu: use handle_percpu_irq handler to avoid dropping interrupts.
  [MIPS] Sibyte: Fix name of clocksource.
  [MIPS] SNI: s/achknowledge/acknowledge/
  [MIPS] Makefile: Fix canonical system names
  [MIPS] vpe: handle halting TCs in an errata safe way.
  [MIPS] Sibyte: Stop timers before programming next even.
  [MIPS] Sibyte: Increase minimum oneshot timer interval to two ticks.
  [MIPS] Lasat: Fix overlap of interrupt number ranges.
  [MIPS] SNI PCIT CPLUS: workaround for b0rked irq wiring of onboard PCI bus 1
  [MIPS] Fix shadow register support.
  [MIPS] Change get_cycles to always return 0.
  [MIPS] Fix typo in R3000 TRACE_IRQFLAGS code
  [MIPS] Sibyte: Replace use of removed IO_SPACE_BASE with IOADDR.
  [MIPS] iounmap if in vr41xx_pciu_init() pci clock is over 33MHz
  [MIPS] BCM1480: Remove duplicate acknowledge of timer interrupt.
  [MIPS] Sibyte: pin timer interrupt to their cores.
  [MIPS] Qemu: Add early printk, your friend in a cold night.
  [MIPS] Convert reference to mem_map to pfn_to_page().
  [MIPS] Sibyte: resurrect old cache hack.

Reported by Chuck Ebbert as:

	https://bugzilla.redhat.com/show_bug.cgi?id=259501#c14

This routine is called each time hash should be replaced, nf_conn has
extension list which contains pointers to connection tracking users
(like nat, which is right now the only such user), so when replace takes
place it should copy own extensions. Loop above checks for own
extension, but tries to move higer-layer one, which can lead to above
oops.
Signed-off-by: NEvgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch enables VLAN support on sunhme by increasing BMAC_TXMAX/BMAC_RXMAX
and allocating extra space via skb_put for the VLAN header.
Signed-off-by: NChris Poon <dev-null@telus.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This matters to any sort of device that is wired to one of the CPU
interrupt pins on an SMP system.  Typically the scenario is most easily
triggered with the count/compare timer interrupt where the same interrupt
number and thus irq_desc is used on each processor.

   CPU A			CPU B

   do_IRQ()
   generic_handle_irq()
   handle_level_irq()
   spin_lock(desc_lock)
   set IRQ_INPROGRESS
   spin_unlock(desc_lock)
				do_IRQ()
				generic_handle_irq()
				handle_level_irq()
				spin_lock(desc_lock)
				IRQ_INPROGRESS set => bail out
   spin_lock(desc_lock)
   clear IRQ_INPROGRESS
   spin_unlock(desc_lock)

In case of the cp0 compare interrupt this means the interrupt will be
acked and not handled or re-armed on CPU b, so there won't be any timer
interrupt until the count register wraps around.

With kernels 2.6.20 ... 2.6.23 we usually were lucky that things were just
working right on VSMP because the count registers are synchronized on
bootup so it takes something that disables interrupts for a long time on
one processor to trigger this one.

For scenarios where an interrupt is multicasted or broadcasted over several
CPUs the existing code was safe and the fix will break it.  There is no
way to know in the interrupt controller code because it is abstracted from
the platform code.  I think we do not have such a setup currently, so this
should be ok.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NMaciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The GNU `config.guess' uses "linux-gnu" as the canonical system name.
Fix the list of compiler prefixes checked to spell it correctly.
Signed-off-by: NMaciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Adds a JR.HB after halting a TC, to ensure that the TC has really halted.
only modifies the TCSTATUS register when the TC is safely halted.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

We have no guarantee by the generic time code that the timer is stopped
when the ->next_event method is called.  Modifying the Timer Initial Count
register while the timer is enabled has UNPREDICTABLE effect according to
the BCM1250/BCM1125/BCM1125H User Manual.  So stop the timer before
reprogramming.

This is a paranoia fix; no ill effects have been observed previously.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

For the old minimum of a single tick a value of zero would be programmed
into the init value register which in the BCM1250/BCM1125/BCM1125H User
Manual in the Timer Special Cases section is documented to have
UNPREDICTABLE effect.

Observable sympthoms of this bug were hangs of several seconds on the
console during bootup and later if both dyntick and highres timer options
were activated.

In theory contiguous mode of the timers is also affected but in an act of
hopeless lack of realism I'll assume nobody will ever configure a KERNEL
for HZ > 500kHz but if so I leave that to evolution to sort out.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The range of MIPS_CPU IRQ and the range of LASAT IRQ overlap.
Signed-off-by: NYoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NThomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Shadow register support would not possibly have worked on multicore
systems.  The support code for it was also depending not on MIPS R2 but
VSMP or SMTC kernels even though it makes perfect sense with UP kernels.

SR sets are a scarce resource and the expected usage pattern is that
users actually hardcode the register set numbers in their code.  So fix
the allocator by ditching it.  Move the remaining CPU probe bits into
the generic CPU probe.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This avoids us executing an mfc0 c0_count instruction on processors which
don't have but also on certain R4000 and R4400 versions where reading from
the count register just in the very moment when its value equals
c0_compare will result in the timer interrupt getting lost.

There is still a number of users of get_cycles remaining outside the
arch code:

crypto/tcrypt.c:                start = get_cycles();
crypto/tcrypt.c:                end = get_cycles();
crypto/tcrypt.c:                start = get_cycles();
crypto/tcrypt.c:                end = get_cycles();
crypto/tcrypt.c:                start = get_cycles();
crypto/tcrypt.c:                end = get_cycles();
drivers/char/hangcheck-timer.c: return get_cycles();
drivers/char/hangcheck-timer.c: printk("Hangcheck: Using get_cycles().\n");
drivers/char/random.c:  sample.cycles = get_cycles();
drivers/input/joystick/analog.c:#define GET_TIME(x)     do { x = get_cycles(); }
include/linux/arcdevice.h:          _x = get_cycles(); \
include/linux/arcdevice.h:          _y = get_cycles(); \
mm/slub.c:      if (!s->defrag_ratio || get_cycles() % 1024 > s->defrag_ratio)
mm/slub.c:      p += 64 + (get_cycles() & 0xff) * sizeof(void *);
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

iounmap if pci clock is over 33MHz.  Cosmetic because the iomap() in this
case is just a bit of address magic.
Signed-off-by: NRoel Kluin <12o3l@tiscali.nl>
Acked-by: NYoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Or strange things will happen.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This was crashing the combination of highmem and sparsemem.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The recent switch of the Sibyte SOCs from the processor specific cache
managment code in c-sb1.c to c-r4k.c lost this old hack

    [MIPS] Hack for SB1 cache issues

    Removing flush_icache_page a while ago broke SB1 which was using an empty
    flush_data_cache_page function.  This glues things well enough so a more
    efficient but also more intrusive solution can be found later.
Signed-Off-By: NThiemo Seufer <ths@networkno.de>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

in the hope it was no longer needed.  As it turns it still is so resurrect
it until there is a better solution.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

eth_type_trans() now sets skb->dev.  Access skb->def after it gets
set.
Signed-off-by: NDivy Le Ray <divy@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It should pass opt to the ->get/->set functions, not ops.
Tested-by: NLuca Tettamanti <kronos.it@gmail.com>
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

* git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-sched:
  sched: reorder SCHED_FEAT_ bits
  sched: make sched_nr_latency static
  sched: remove activate_idle_task()
  sched: fix __set_task_cpu() SMP race
  sched: fix SCHED_FIFO tasks & FAIR_GROUP_SCHED
  sched: fix accounting of interrupts during guest execution on s390