The pov protab2-ips9 tablet uses the A10's integrated audio codec,
enable it.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The UTOO P66 tablet uses the A13's integrated audio codec, enable it.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The Olimex A20-SOM-EVB is an evaluation board for the Olimex
A20-SOM system-on-module. The baseboard provides a full-size SD
socket (connected to mmc3) in addition to the micro-SD socket on
the SOM itself (which is connected to mmc0).

Enable the mmc3 controller in the dts.
Signed-off-by: NKarsten Merker <merker@debian.org>
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The Olimex A20-SOM-EVB is an evaluation board for the Olimex
A20-SOM system-on-module.  It provides a set of android-style
buttons (labeled "VOL+", "VOL-", "MENU", "SEARCH", "HOME", "ESC"
and "ENTER") which are connected to a low-resolution ADC via a
resistor network.

This patch adds appropriate button definitions to the board
dts. The voltages assigned to the keys are specified in the
board schematics published by the manufacturer.
Signed-off-by: NKarsten Merker <merker@debian.org>
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The Reduced Serial Bus (RSB) controller is used to talk to the 3
companion ICs (2 PMICs, 1 RTC/codec IC) on the board.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The Cubieboard4 has a consumer IR receiver. Enable it in the DT.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The Cubieboard4 has 2 controllable LEDs, 1 red and 1 green.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The video engine has its own module clock, which also includes a
reset control for it.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The video engine has its own module clock, which also includes a
reset control for it.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The Orange Pi Plus is a SBC based on the Allwinner H3 SoC
with 8GB eMMC, multiple USB ports through a USB hub chip, SATA through
a USB-SATA bridge, one uSD slot, a 10/100/1000M ethernet port,
WiFi, HDMI, headphone jack, IR receiver, a microphone, a CSI connector
and a 40-pin GPIO header.
Signed-off-by: NJens Kuske <jenskuske@gmail.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The Allwinner H3 is a home entertainment system oriented SoC with
four Cortex-A7 cores and a Mali-400MP2 GPU.
Signed-off-by: NJens Kuske <jenskuske@gmail.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The DRAM gates controls direct memory access for some peripherals.
These peripherals include the display pipeline, so add the required
gates to the simplefb nodes as well.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The DRAM gates controls direct memory access for some peripherals.
These peripherals include the display pipeline, so add the required
gates to the simplefb nodes as well.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The Allwinner A80 SoC has an NMI controller. NMI is an external
interrupt pin exclusely used with PMICs and other system critical
peripherals (such as RTC) in Allwinner's reference designs.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Reviewed-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This patch adds a device node for the Reduced Serial Bus (RSB)
controller and the defacto pinmux setting to the A80 dtsi.

Since there is only one possible pinmux setting for RSB, just
set it in the dtsi.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The A80 Optimus board has a consumer IR receiver. Enable it in the DT.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The Allwinner A80 SoC has a consumer IR receiver, which is the same as
older SoCs.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

LED3 is connected to pin PM15 on R_PIO.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The A80 has a secondary pin controller. Add a device node for it.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The main (24MHz) clock on the A80 is configurable via the PRCM address
space. The low power/speed (32kHz) clock is from an external chip, the
AC100.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This adds the supported PRCM clocks and reset controls to the A80 dtsi.
The DAUDIO module clocks are not supported yet.

Also update clock and reset phandles for r_uart.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add a node describing the touchscreen found on the pov protab2-ips9
tablet.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add a node describing the touchscreen controller used on the iNet1 tablet.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Enable the on-chip audio codec
Signed-off-by: NStefan Monnier <monnier@iro.umontreal.ca>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Enable the on-chip audio codec
Signed-off-by: NStefan Monnier <monnier@iro.umontreal.ca>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add a node describing the AXP152 pmic used on Auxtek T004 boards.
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMichael van Slingerland <michael@deviousops.nl>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add a node describing the lcd panel backlight on the pov protab2 ips9
tablet.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add a node describing the lcd panel backlight on the UTOO P66 tablet.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add a node describing the lcd panel backlight on the iNet1 tablet.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The iNet1 tablet uses the A10's integrated audio codec, enable it.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Some boards, such as tablets, have regulators providing power to parts
of the display pipeline, like signal converters and LCD panels.

Add labels to the simplefb device nodes so that we can reference them
in the board dts files to add regulator supply properties.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Gemei G9 has internal speakers and headphone jack. Audio switching
from internal speakers to headphones is automatically handled by
extra FT2012Q audio amplifier chip that works out of the box.
Signed-off-by: NPriit Laes <plaes@plaes.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

ADC seems to be using ldo2 for reference voltage.
Signed-off-by: NPriit Laes <plaes@plaes.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add regulator nodes for axp209 using the axp209.dtsi include.
Signed-off-by: NPriit Laes <plaes@plaes.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The inet9f-rev03 tablet has multiple fire-buttons / direction controls,
add support for these using the same axis mapping as ps2 compatible game
controllers with the same stick / button layout use.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Enable the on-chip audio codec
Signed-off-by: NJelle van der Waa <jelle@vdwaa.nl>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Enable on-chip audio codec on the Wexler TAB7200 tablet.
Signed-off-by: NAleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Enable the on-chip audio codec on the Olimex A20-SOM-EVB
Signed-off-by: NMarcus Weseloh <mweseloh42@gmail.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Enable the axp221 PMIC chip in the dts file.

Allows board to power off correctly from the poweroff command

This board requires dc1sw to be enabled in order to provide a power source
for the 5V DCDC converter that powers USB2.

This board uses dldo1 for 3.3V wifi power

This board requires dldo3 to be enabled at 2.8V in order to provide voltage
to the pullup resistors for the i2c0 bus.
Signed-off-by: NLawrence Yu <lyu@micile.com>
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>