Chip is calibrated by the manufacturer.  There is no need to calibarate it
at driver level.  If the chip is used as a joystick, calibaration can be
done using joystick device calibration mechanism.
Signed-off-by: NSamu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: NÉric Piel <Eric.Piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Implement selftest feature as specified by chip manufacturer.  Control:
read selftest sysfs entry

Response: "OK x y z" or "FAIL x y z"

where x, y, and z are difference between selftest mode and normal mode.
Test is passed when values are within acceptance limit values.

Acceptance limits are provided via platform data.  See chip spesifications
for acceptance limits.  If limits are not properly set, OK / FAIL decision
is meaningless.  However, userspace application can still make decision
based on the numeric x, y, z values.

Selftest is meant for HW diagnostic purposes.  It is not meant to be
called during normal use of the chip.  It may cause false interrupt
events.  Selftest mode delays polling of the normal results but it doesn't
cause wrong values.  Chip must be in static state during selftest.  Any
acceration during the test causes most probably failure.
Signed-off-by: NSamu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: NÉric Piel <Eric.Piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Lis3 accelerometer sensors have quite long power on delay (up to 125
ms). This patch adds necessary delay to power on sequence for currently
supported lis3 chips.
Signed-off-by: NSamu Onkalo <samu.p.onkalo@nokia.com>
Tested-by: NÉric Piel <eric.piel@tremplin-utc.net>
Acked-by: NÉric Piel <eric.piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Originally the driver was only targeted to 12bits sensors.  When support
for 8bits sensors was added, some slight difference in the registers were
overlooked.  This should fix it, both for initialization, and for
displaying the rate.
Reported-by: NKalhan Trisal <kalhan.trisal@intel.com>
Reported-by: NChristoph Plattner <christoph.plattner@gmx.at>
Tested-by: NChristoph Plattner <christoph.plattner@gmx.at>
Tested-by: NSamu Onkalo <samu.p.onkalo@nokia.com>
Signed-off-by: NÉric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NSamu Onkalo <samu.p.onkalo@nokia.com>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Most of the documentation and comments were written when the driver was
only supporting one type of chip, only via ACPI/HP. Update the info to
the much clearer understanding that we have now.
Signed-off-by: NÉric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NSamu Onkalo <samu.p.onkalo@nokia.com>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

polled input device itself was not free'd.
Signed-off-by: NSamu Onkalo <samu.p.onkalo@nokia.com>
Tested-by: NÉric Piel <eric.piel@tremplin-utc.net>
Acked-by: NÉric Piel <eric.piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Send input_sync after each measurement round. This helps userspace to
detect which reported values belongs to the same measurement.
Signed-off-by: NSamu Onkalo <samu.p.onkalo@nokia.com>
Tested-by: NÉric Piel <eric.piel@tremplin-utc.net>
Acked-by: NÉric Piel <eric.piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add control of fan minimum turn-on output levels, decoupling it from the
fan turn-off output level.  Add control of rate of change of fan output
level.  These in turn allow lower turn-off rotor speed and smoother
transitions for better thermal and acoustic control authority.  Add
support for constant fan speed and proportional-response operations modes.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NDaniel J Blueman <daniel.blueman@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: David Hubbard <david.c.hubbard@gmail.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add the possibility to remap axes via platform data.  Function pointers
for resource setup and release purposes
Signed-off-by: NSamu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: NÉric Piel <eric.piel@tremplin-utc.net>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Jean Delvare <khali@linux-fr.org>
Cc:  "Trisal, Kalhan" <kalhan.trisal@intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Move common crc body to new function crc32_body() cleaup and micro
optimize crc32_body for speed and less size.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NJoakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Improve the /proc/interrupts output so the irq number can be mapped to
platform device on boards with multiple tmio_mmc instances.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Cc: <linux-mmc@vger.kernel.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add SD host driver for Blackfin BF54x and BF51x.

[akpm@linux-foundation.org: fix layout, c99 warning]
Signed-off-by: NCliff Cai <cliffcai.sh@gmail.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This new revision of the IP adds some improvements to the MCI already
present in several Atmel SOC.

Some new registers are added and a particular way of handling DMA
interaction lead to a new sequence in function call which is backward
compatible: On MCI2, we must set the DMAEN bit to enable the DMA
handshaking interface.  This must happen before the data transfer command
is sent.

A new function is able to differentiate MCI2 code and is based on
knowledge of processor id (cpu_is_xxx()).
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NHaavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Allow the use of another DMA controller driver in atmel-mci sd/mmc driver.
 This adds a generic dma_slave pointer to the mci platform structure where
we can store DMA controller information.  In atmel-mci we use information
provided by this structure to initialize the driver (with new helper
functions that are architecture dependant).

This also adds at32/avr32 chip modifications to cope with this new access
method.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Some people run general-purpose distribution kernels on netbooks with
a card that is physically non-removable or logically non-removable
(e.g. used for /home) and cannot be cleanly unmounted during suspend.
Add a module parameter to set whether cards are assumed removable or
non-removable, with the default set by CONFIG_MMC_UNSAFE_RESUME.

In general, it is not possible to tell whether a card present in an MMC
slot after resume is the same that was there before suspend.  So there are
two possible behaviours, each of which will cause data loss in some cases:

CONFIG_MMC_UNSAFE_RESUME=n (default): Cards are assumed to be removed
during suspend.  Any filesystem on them must be unmounted before suspend;
otherwise, buffered writes will be lost.

CONFIG_MMC_UNSAFE_RESUME=y: Cards are assumed to remain present during
suspend.  They must not be swapped during suspend; otherwise, buffered
writes will be flushed to the wrong card.

Currently the choice is made at compile time and this allows that to be
overridden at module load time.
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Cc: Wouter van Heyst <larstiq@larstiq.dyndns.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Convert two missed s3c2410 specific gpio calls to gpiolib calls.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NSimtec Linux Team <linux@simtec.co.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This is still in use especially to develop SDIO device drivers on laptop
machines which are lacking SDIO slots.  This adapter supports SDIO cards
only due to lack of 136-bit response capability.
Signed-off-by: NNicolas Pitre <nico@marvell.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove check for host->iclk being NULL from error path since we already
know it is non-null and use return value from clk_get.
Signed-off-by: NLadislav Michl <ladis@linux-mips.org>
Acked-by: NTony Lindgren <tony@atomide.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add cpufreq support to MMC driver. The clock divider value has to be
modified according to the controller input frequency.
Signed-off-by: NChaithrika U S <chaithrika@ti.com>
Cc: Linus Walleij <linus.ml.walleij@gmail.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Currently DaVinci EDMA driver supports multiple EDMA channel controller
instances.  edma_alloc_channel() api returns a 32 bit value which has the
channel controller number in MSB and the EDMA channel number in LSB.  The
variables which store the value returned by edma_alloc_channel() have to
be 32 bit wide now.
Signed-off-by: NSudhakar Rajashekhara <sudhakar.raj@ti.com>
Acked-by: NVipin Bhandari <vipin.bhandari@ti.com>
Cc: Purshotam Kumar <purushotam@ti.com>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add support for MMC/SD controller driver for all DaVinci family SoC.  This
patch supports davinci family SoC's DM6446, DM355, DM365 and
DA830/OMAPL137.

The patch has been tested on DM355 EVM.

The MMCSD controller specifications for DM355 can be found at
http://focus.ti.com/general/docs/litabsmultiplefilelist.tsp?literatureNumber=spruee2cSigned-off-by: NVipin Bhandari <vipin.bhandari@ti.com>
Signed-off-by: NPurshotam Kumar <purushotam@ti.com>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If the NULL test on mrq is needed, then the derefernce should be after the
NULL test.

A simplified version of the semantic match that detects this problem is as
follows (http://coccinelle.lip6.fr/):

// <smpl>
@match exists@
expression x, E;
identifier fld;
@@

* x->fld
  ... when != \(x = E\|&x\)
* x == NULL
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Rework the current CIS tuple parsing code, reusing the existing
infrastructure and providing an easy way to add new CISTPL_FUNCE parsers
by TPLFE_TYPE.

Valid known CIS tuples are now silently queued for the SDIO function
driver when not parsed/processed (-EILSEQ) by the SDIO core.  Unknown CIS
tuples (-ENOENT) are queued too for the SDIO function driver without
aborting the initialization, but emit a warning in the kernel log.

CISTPL_FUNCE tuples can be "whitelisted" now by adding a matching entry to
the cis_tpl_funce_list table.
Signed-off-by: NAlbert Herranz <albert_herranz@yahoo.es>
Acked-by: NPierre Ossman <pierre@ossman.eu>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

After a failing allocation of mmc or a failed ioremap in mxcmci_probe host was
used uninitialized.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Martin Fuzzey <mfuzzey@gmail.com>
Cc: Pierre Ossman <drzeus@drzeus.cx>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Rather than have the EDD depend on !ia64 (and assuming that only ia64,
x86, x86_64 will be including this Kconfig), have EDD depend on the only
arches which can support this code.  This should allow all other arches to
cleanly include the firmware Kconfig.

Also simplify the x86 string used by FIRMWARE_MEMMAP to match EDD.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Acked-by: NMatt Domsch <Matt_Domsch@dell.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Recently, We marked strstrip() as must_check.  because it was frequently
misused and it should be checked.  However, we found one exception.
scsi/ipr.c intentionally ignore return value of strstrip.  Because it
wishes to keep the whitespace at the beginning.

Thus we need to keep with and without checked whitespace trim function.
This patch adds a new strim() and changes ipr.c to use it.

[akpm@linux-foundation.org: coding-style fixes]
Suggested-by: NAlan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NKOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Shrinks vmlinux

without:
$ size vmlinux
   text    data     bss     dec     hex filename
6975863  679652 1359668 9015183  898f8f vmlinux

with:
$ size vmlinux
   text    data     bss     dec     hex filename
6975639 679652 1359668 9014959 898eaf vmlinux
Signed-off-by: NJoe Perches <joe@perches.com>
Cc: Jeff Garzik <jgarzik@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NJoe Perches <joe@perches.com>
Cc: Artem Bityutskiy <dedekind@infradead.org>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NJoe Perches <joe@perches.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NJoe Perches <joe@perches.com>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NJoe Perches <joe@perches.com>
Cc: Jeff Garzik <jgarzik@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NMatt Mackall <mpm@selenic.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NAlex Elder <aelder@sgi.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

UUID/GUIDs are somewhat common in kernel source.

Standardize the printed style of UUID/GUIDs by using
another extension to %p.

%pUb:   01020304-0506-0708-090a-0b0c0d0e0f10
%pUB:   01020304-0506-0708-090A-0B0C0D0E0F10 (upper case)
%pUl:   04030201-0605-0807-090a-0b0c0d0e0f10
%pUL:   04030201-0605-0807-090A-0B0C0D0E0F10 (upper case)

%pU defaults to %pUb
Signed-off-by: NJoe Perches <joe@perches.com>
Cc: Jeff Garzik <jgarzik@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Alex Elder <aelder@sgi.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Artem Bityutskiy <dedekind@infradead.org>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

No functional change.  Cache strlen() result to avoid recalculating it up
to 3 times on the worst case.

Reduces code size a little by 32 bytes:
   text    data     bss     dec     hex filename
   1385       0       0    1385     569 lib/parser.o-BEFORE
   1353       0       0    1353     549 lib/parser.o-AFTER
Signed-off-by: NAndré Goddard Rosa <andre.goddard@gmail.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Makes use of skip_spaces() defined in lib/string.c for removing leading
spaces from strings all over the tree.

It decreases lib.a code size by 47 bytes and reuses the function tree-wide:
   text    data     bss     dec     hex filename
  64688     584     592   65864   10148 (TOTALS-BEFORE)
  64641     584     592   65817   10119 (TOTALS-AFTER)

Also, while at it, if we see (*str && isspace(*str)), we can be sure to
remove the first condition (*str) as the second one (isspace(*str)) also
evaluates to 0 whenever *str == 0, making it redundant. In other words,
"a char equals zero is never a space".

Julia Lawall tried the semantic patch (http://coccinelle.lip6.fr) below,
and found occurrences of this pattern on 3 more files:
    drivers/leds/led-class.c
    drivers/leds/ledtrig-timer.c
    drivers/video/output.c

@@
expression str;
@@

( // ignore skip_spaces cases
while (*str &&  isspace(*str)) { \(str++;\|++str;\) }
|
- *str &&
isspace(*str)
)
Signed-off-by: NAndré Goddard Rosa <andre.goddard@gmail.com>
Cc: Julia Lawall <julia@diku.dk>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Neil Brown <neilb@suse.de>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: David Howells <dhowells@redhat.com>
Cc: <linux-ext4@vger.kernel.org>
Cc: Samuel Ortiz <samuel@sortiz.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

... so that strlen() iterates over a smaller string comprising of the
remaining characters only.
Signed-off-by: NAndré Goddard Rosa <andre.goddard@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

On the following sentence:
    while (*s && isspace(*s))
        s++;

If *s == 0, isspace() evaluates to ((_ctype[*s] & 0x20) != 0), which
evaluates to ((0x08 & 0x20) != 0) which equals to 0 as well.
If *s == 1, we depend on isspace() result anyway. In other words,
"a char equals zero is never a space", so remove this check.

Also, *s != 0 is most common case (non-null string).

Fixed const return as noticed by Jan Engelhardt and James Bottomley.
Fixed unnecessary extra cast on strstrip() as noticed by Jan Engelhardt.
Signed-off-by: NAndré Goddard Rosa <andre.goddard@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

To avoid a collision with the newly-added kernel-wide skip_spaces().
Signed-off-by: NAndré Goddard Rosa <andre.goddard@gmail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

While at it, use tabs to indent the comments.
Signed-off-by: NAndré Goddard Rosa <andre.goddard@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>