devm_fwnode_get_gpiod_from_child() currently allows GPIO users to
request a GPIO that is defined in a child fwnode instead of directly in
the device fwnode.
Extend this API by adding the devm_fwnode_get_index_gpiod_from_child()
helper which does the same except you can also specify an index in case
the 'xx-gpios' property describe several GPIOs.
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Rename devm_get_gpiod_from_child() into
devm_fwnode_get_gpiod_from_child() to reflect the fact that this
function is operating on a fwnode object.
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: NJacek Anaszewski <jacek.anaszewski@gmail.com>
Acked-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Currently all users of fwnode_get_named_gpiod() have no way to
specify a label for the GPIO. So GPIOs listed in debugfs are shown
with label "?". With this change a proper label is used.

Also adjust all users so they can pass a label, properly retrieved
from device tree properties.
Signed-off-by: NAlexander Stein <alexander.stein@systec-electronic.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: NJacek Anaszewski <jacek.anaszewski@gmail.com>
Acked-by: NBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Make fwnode_get_named_gpiod() consistent with the rest of
gpiod_get() like API, i.e. configure GPIO pin immediately after
request.

Besides obvious clean up it will help to configure pins based
on firmware provided resources.
Reviewed-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This tries to simplify the use of CONFIG_GPIOLIB_IRQCHIP when
using threaded interrupts: add a new call
gpiochip_irqchip_add_nested() to indicate that we're dealing
with a nested rather than a chained irqchip, then create a
separate gpiochip_set_nested_irqchip() to mirror
the gpiochip_set_chained_irqchip() call to connect the
parent and child interrupts.

In the nested case gpiochip_set_nested_irqchip() does nothing
more than call irq_set_parent() on each valid child interrupt,
which has little semantic effect in the kernel, but this is
probably still formally correct.

Update all drivers using nested interrupts to use
gpiochip_irqchip_add_nested() so we can now see clearly
which these users are.

The DLN2 driver can drop its specific hack with
.irq_not_threaded as we now recognize whether a chip is
threaded or not from its use of gpiochip_irqchip_add_nested()
signature rather than from inspecting .can_sleep.

We rename the .irq_parent to .irq_chained_parent since this
parent IRQ is only really kept around for the chained
interrupt handlers.

Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Octavian Purdila <octavian.purdila@intel.com>
Cc: Daniel Baluta <daniel.baluta@intel.com>
Cc: Bin Gao <bin.gao@linux.intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Ajay Thomas <ajay.thomas.david.rajamanickam@intel.com>
Cc: Semen Protsenko <semen.protsenko@globallogic.com>
Cc: Alexander Stein <alexander.stein@systec-electronic.com>
Cc: Phil Reid <preid@electromag.com.au>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

It should have been @reg_clr instead of @reg_clk
Signed-off-by: NAnthony Best <anthonybest@bestanthony.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Kernel source files need not include <linux/kconfig.h> explicitly
because the top Makefile forces to include it with:

  -include $(srctree)/include/linux/kconfig.h

This commit removes explicit includes except the following:

  * arch/s390/include/asm/facilities_src.h
  * tools/testing/radix-tree/linux/kernel.h

These two are used for host programs.

Link: http://lkml.kernel.org/r/1473656164-11929-1-git-send-email-yamada.masahiro@socionext.comSigned-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When using GPIO irqchip helpers to setup irqchip for a gpiolib based
driver, it is not possible to select which GPIOs to add to the IRQ domain.
Instead it just adds all GPIOs which is not always desired. For example
there might be GPIOs that for some reason cannot generated normal
interrupts at all.

To support this we add a flag irq_need_valid_mask to struct gpio_chip. When
this flag is set the core allocates irq_valid_mask that holds one bit for
each GPIO the chip has. By default all bits are set but drivers can
manipulate this using set_bit() and clear_bit() accordingly.

Then when gpiochip_irqchip_add() is called, this mask is checked and all
GPIOs with bit is set are added to the IRQ domain created for the GPIO
chip.
Suggested-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Most shared headers in include/linux don't need to know what the
internals of a struct module are; all they care about is that it
is a struct and hence they may require a pointer to one.

The advantage in this is that module.h is including a lot of stuff
itself, and an otherwise empty C file that just contains module.h
will result in ~750kB from CPP (compared to say 12kB from init.h)

So we have approximately 50 instances of "struct module;" in the
various include/linux headers already that help us keep module.h
out of other headers; here we do the same for gpio.

Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Some GPIO controllers has a special hardware bit we can flip
to support open drain / source. This means that on these hardwares
we do not need to emulate OD/OS by setting the line to input
instead of actively driving it high/low. Add an optional vtable
callback to the driver set_single_ended() so that driver can
implement this in hardware if they have it.

We may need a pinctrl_gpio_set_config() call at some point to
propagate this down to a backing pin control device on systems
with split GPIO/pin control.
Reported-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Add device managed APIs devm_gpiochip_add_data() and
devm_gpiochip_remove() for the APIs gpiochip_add_data()
and gpiochip_remove().

This helps in reducing code in error path and sometimes
removal of .remove callback for driver unbind.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>

The gpio_chip label is useful for userspace to understand what
kind of GPIO chip it is dealing with. Let's store a copy of this
label in the gpio_device, add it to the struct passed to userspace
for GPIO_GET_CHIPINFO_IOCTL and modify lsgpio to show it.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

My left hand merges code to privatize the descriptor handling
while my right hand merges drivers that poke around and
disrespect with the same gpiolib internals.

So let's expose the proper APIs for drivers to ask the gpiolib
core if a line is marked as open drain or open source and
get some order around things so this driver compiles again.
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Cc: Nicolas Saenz Julienne <nicolassaenzj@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

We move to manage this pointer under gpiolib control rather than
leave it in the subdevice's gpio_chip. We can not NULL it after
gpiochip_remove so at to keep things tight.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Instead of keeping this reference to the pin ranges in the
client driver-supplied gpio_chip, move it to the internal
gpio_device as the drivers have no need to inspect this.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This kind of hacks disturbs the refactoring of the gpiolib.

The descriptor table belongs to the gpiolib, if we want to know
something about something in it, use or define the proper accessor
functions. Let's add this gpiochip_lins_is_irq() to do what the
sunxi driver is trying at so we can privatize the descriptors
properly.

Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

We need gpio_device to hold the descriptors so that they can
be lifecycled with the struct gpio_device held from userspace.
Move the descriptor array into gpio_device. Also rename it from
"desc" (singularis) to "descs" (pluralis) to reflect the fact
that it is an array.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Since gpio_device is the struct that survives if the backing
gpio_chip is removed, move the sysfs mock device to this state
container so it becomes part of the dangling state of the
GPIO device on removal.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

GPIO chips have been around for years, but were never real devices,
instead they were piggy-backing on a parent device (such as a
platform_device or amba_device) but this was always optional.
GPIO chips could also exist without any device at all, with its
struct device *parent (ex *dev) pointer being set to null.

When sysfs was in use, a mock device would be created, with the
optional parent assigned, or just floating orphaned with NULL
as parent.

If sysfs is active, it will use this device as parent.

We now create a gpio_device struct containing a real
struct device and move the subsystem over to using that. The
list of struct gpio_chip:s is augmented to hold struct
gpio_device:s and we find gpio_chips:s by first looking up
the struct gpio_device.

The struct gpio_device is designed to stay around even if the
gpio_chip is removed, so as to satisfy users in userspace
that need a backing data structure to hold the state of the
session initiated with e.g. a character device even if there is
no physical chip anymore.

From this point on, gpiochips are devices.

Cc: Johan Hovold <johan@kernel.org>
Cc: Michael Welling <mwelling@ieee.org>
Cc: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Board files that define their own bgpio_pdata are broken when
CONFIG_GPIO_GENERIC is disabled and the bgpio_pdata structure
definition is hidden by the #ifdef:

arch/arm/mach-clps711x/board-autcpu12.c:148:15: error: variable 'autcpu12_mmgpio_pdata' has initializer but incomplete type
 static struct bgpio_pdata autcpu12_mmgpio_pdata __initdata = {
arch/arm/mach-clps711x/board-autcpu12.c:149:2: error: unknown field 'base' specified in initializer
  .base = AUTCPU12_MMGPIO_BASE,

Since the board files should generally not care what drivers are
enabled, this makes the structure definition visible again.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Fixes: 0f4630f3 ("gpio: generic: factor into gpio_chip struct")
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The separate struct bgpio_chip has been a pain to handle, both
by being confusingly similar in name to struct gpio_chip and
for being contained inside a struct so that struct gpio_chip
is contained in a struct contained in a struct, making several
steps of dereferencing necessary.

Make things simpler: include the fields directly into
<linux/gpio/driver.h>, #ifdef:ed for CONFIG_GENERIC_GPIO, and
get rid of the <linux/basic_mmio_gpio.h> altogether. Prefix
some of the member variables with bgpio_* and add proper
kerneldoc while we're at it.

Modify all users to handle the change and use a struct
gpio_chip directly. And while we're at it: replace all
container_of() dereferencing by gpiochip_get_data() and
registering the gpio_chip with gpiochip_add_data().

Cc: arm@kernel.org
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: Olof Johansson <olof@lixom.net>
Cc: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Cc: Rabin Vincent <rabin@rab.in>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-omap@vger.kernel.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: bcm-kernel-feedback-list@broadcom.com
Acked-by: NGregory Fong <gregory.0xf0@gmail.com>
Acked-by: NLiviu Dudau <Liviu.Dudau@arm.com>
Acked-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Acked-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This adds a void * pointer to gpio_chip so that driver can
assign and retrieve some states. This is done to get rid of
container_of() calls for gpio_chips embedded inside state
containers, so we can remove the need to have the gpio_chip
or later (planned) struct gpio_device be dynamically allocated
at registration time, so that its struct device can be properly
reference counted and not bound to its parent device (e.g.
a platform_device) but instead live on after unregistration
if it is opened by e.g. a char device or sysfs.

The data is added with the new function gpiochip_add_data()
and for compatibility we add static inline wrapper function
gpiochip_add() that will call gpiochip_add_data() with
NULL as argument. The latter will be removed once we have
exorcised gpiochip_add() from the kernel.

gpiochip_get_data() is added as a static inline accessor
for drivers to quickly get their data out.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Since gpiochip .get() callback may return a negative error value, it
strictly limits the range of possible non-error returned values to
a subset of [30:0] bitmask, however on practice on success all
gpiochip drivers return either 0 for low signal or 1 for high signal,
this is assured by "gpio: *: Be sure to clamp return value" series of
changes. To avoid any confusion, misinterpretation and potential
errors while developing gpiochip drivers in future convert this
implicit assumption to a mandatory rule.

For output signals with unknown output signal state gpiochip drivers
should return a negative error instead of 0.
Signed-off-by: NVladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The name .dev in a struct is normally reserved for a struct device
that is let us say a superclass to the thing described by the struct.
struct gpio_chip stands out by confusingly using a struct device *dev
to point to the parent device (such as a platform_device) that
represents the hardware. As we want to give gpio_chip:s real devices,
this is not working. We need to rename this member to parent.

This was done by two coccinelle scripts, I guess it is possible to
combine them into one, but I don't know such stuff. They look like
this:

@@
struct gpio_chip *var;
@@
-var->dev
+var->parent

and:

@@
struct gpio_chip var;
@@
-var.dev
+var.parent

and:

@@
struct bgpio_chip *var;
@@
-var->gc.dev
+var->gc.parent

Plus a few instances of bgpio that I couldn't figure out how
to teach Coccinelle to rewrite.

This patch hits all over the place, but I *strongly* prefer this
solution to any piecemal approaches that just exercise patch
mechanics all over the place. It mainly hits drivers/gpio and
drivers/pinctrl which is my own backyard anyway.

Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Alek Du <alek.du@intel.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Acked-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: NLee Jones <lee.jones@linaro.org>
Acked-by: NJiri Kosina <jkosina@suse.cz>
Acked-by: NHans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: NJacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Provide generic request/free implementations that pinctrl aware gpio
drivers can use instead of open coding if they use a 1:1 pin to gpio
signal mapping.
Signed-off-by: NJonas Gorski <jogo@openwrt.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This refactors the changes to the GPIO line naming mechanism to
not have so widespread effects, instead we conclude the patch series
by having created a name attribute in the GPIO descriptor, that need
not be globally unique, and it will be initialized from the old
.names array in struct gpio_chip if it exists, then used in the legacy
sysfs code like the array was used previously.

The associated changes to name lines from the device tree are
controversial and need to stand alone from this. Resulting changes:

1. Remove the export and the header for the gpio_name_to_desc() as so
far the only use is inside gpiolib.c. Staticize gpio_name_to_desc()
and move it above the only function using it.

2. Only print a warning if there are two GPIO lines with the same name.
The reason is to preserve current behaviour: before the previous
changes to the naming mechanism this would not reject probing the
driver, instead the error would occur when trying to export the line
in sysfs, so restore this behaviour, but print a friendly warning
if names collide.

Cc: Johan Hovold <johan@kernel.org>
Cc: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The latest gpio hogging mechanism assigns each gpio a 'line-name' in the
devicetree. The 'name' field is different from the 'label' field.
'label' is only used for requested GPIOs to describe its current use by
driver or userspace.

The 'name' field describes the GPIO itself, not the use. This is most
likely identical to the label in the schematic on the GPIO line and
should help to find this particular GPIO.

This is equivalent to the gpiochip->names array. However names should be
stored in the GPIO descriptor. We will use gpiochip->names in the future
only as initializer for the GPIO descriptors for drivers that assign
GPIO names hardcoded. All other GPIO names will be parsed from DT and
directly assigned to the GPIO descriptor.

This patch adds a helper function to find gpio descriptors by name
instead of gpio number.
Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Add missed description for GPIO irqchip fields in struct gpio_chip.
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Since IRQ chip helpers were introduced drivers lose ability to
register separate lockdep classes for each registered GPIO IRQ
chip and the gpiolib now is using shared lockdep class for
all GPIO IRQ chips (gpiochip_irq_lock_class).
As result, lockdep will produce warning when there are min two
stacked GPIO chips and all of them are interrupt controllers.

HW configuration which generates lockdep warning (TI dra7-evm):

[SOC GPIO bankA.gpioX]
  <- irq - [pcf875x.gpioY]
            <- irq - DevZ.enable_irq_wake(pcf_gpioY_irq);
The issue was reported in [1] and discussed [2].

=============================================
[ INFO: possible recursive locking detected ]
4.2.0-rc6-00013-g5d050ed-dirty #55 Not tainted
---------------------------------------------
sh/63 is trying to acquire lock:
 (class){......}, at: [<c009b91c>] __irq_get_desc_lock+0x50/0x94

but task is already holding lock:
 (class){......}, at: [<c009b91c>] __irq_get_desc_lock+0x50/0x94

other info that might help us debug this:
 Possible unsafe locking scenario:

       CPU0
       ----
  lock(class);
  lock(class);

 *** DEADLOCK ***

 May be due to missing lock nesting notation

7 locks held by sh/63:
 #0:  (sb_writers#4){.+.+.+}, at: [<c016bbb8>] vfs_write+0x13c/0x164
 #1:  (&of->mutex){+.+.+.}, at: [<c01debf4>] kernfs_fop_write+0x4c/0x1a0
 #2:  (s_active#36){.+.+.+}, at: [<c01debfc>] kernfs_fop_write+0x54/0x1a0
 #3:  (pm_mutex){+.+.+.}, at: [<c009758c>] pm_suspend+0xec/0x4c4
 #4:  (&dev->mutex){......}, at: [<c03f77f8>] __device_suspend+0xd4/0x398
 #5:  (&gpio->lock){+.+.+.}, at: [<c009b940>] __irq_get_desc_lock+0x74/0x94
 #6:  (class){......}, at: [<c009b91c>] __irq_get_desc_lock+0x50/0x94

stack backtrace:
CPU: 0 PID: 63 Comm: sh Not tainted 4.2.0-rc6-00013-g5d050ed-dirty #55
Hardware name: Generic DRA74X (Flattened Device Tree)
[<c0016e24>] (unwind_backtrace) from [<c0013338>] (show_stack+0x10/0x14)
[<c0013338>] (show_stack) from [<c05f6b24>] (dump_stack+0x84/0x9c)
[<c05f6b24>] (dump_stack) from [<c00903f4>] (__lock_acquire+0x19c0/0x1e20)
[<c00903f4>] (__lock_acquire) from [<c0091098>] (lock_acquire+0xa8/0x128)
[<c0091098>] (lock_acquire) from [<c05fd61c>] (_raw_spin_lock_irqsave+0x38/0x4c)
[<c05fd61c>] (_raw_spin_lock_irqsave) from [<c009b91c>] (__irq_get_desc_lock+0x50/0x94)
[<c009b91c>] (__irq_get_desc_lock) from [<c009c4f4>] (irq_set_irq_wake+0x20/0xfc)
[<c009c4f4>] (irq_set_irq_wake) from [<c0393ac4>] (pcf857x_irq_set_wake+0x24/0x54)
[<c0393ac4>] (pcf857x_irq_set_wake) from [<c009c560>] (irq_set_irq_wake+0x8c/0xfc)
[<c009c560>] (irq_set_irq_wake) from [<c04a02ac>] (gpio_keys_suspend+0x70/0xd4)
[<c04a02ac>] (gpio_keys_suspend) from [<c03f6a00>] (dpm_run_callback+0x50/0x124)
[<c03f6a00>] (dpm_run_callback) from [<c03f7830>] (__device_suspend+0x10c/0x398)
[<c03f7830>] (__device_suspend) from [<c03f90f0>] (dpm_suspend+0x134/0x2f4)
[<c03f90f0>] (dpm_suspend) from [<c0096e20>] (suspend_devices_and_enter+0xa8/0x728)
[<c0096e20>] (suspend_devices_and_enter) from [<c00977cc>] (pm_suspend+0x32c/0x4c4)
[<c00977cc>] (pm_suspend) from [<c0096060>] (state_store+0x64/0xb8)
[<c0096060>] (state_store) from [<c01dec64>] (kernfs_fop_write+0xbc/0x1a0)
[<c01dec64>] (kernfs_fop_write) from [<c016b280>] (__vfs_write+0x20/0xd8)
[<c016b280>] (__vfs_write) from [<c016bb0c>] (vfs_write+0x90/0x164)
[<c016bb0c>] (vfs_write) from [<c016c330>] (SyS_write+0x44/0x9c)
[<c016c330>] (SyS_write) from [<c000f500>] (ret_fast_syscall+0x0/0x54)

Lets fix it by using separate lockdep class for each registered GPIO
IRQ Chip. This is done by wrapping gpiochip_irqchip_add call into macros.

The implementation of this patch inspired by solution done by Nicolas
Boichat for regmap [3]

[1] http://www.spinics.net/lists/linux-gpio/msg05844.html
[2] http://www.spinics.net/lists/linux-gpio/msg06021.html
[3] http://www.spinics.net/lists/arm-kernel/msg429834.html

Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roger Quadros <rogerq@ti.com>
Reported-by: NRoger Quadros <rogerq@ti.com>
Tested-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

In case we unload and load a driver module again that is registering a
lookup table, without this it will result in multiple entries. Provide
an option to remove the lookup table on driver unload

Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Reviewed-by: NAlexandre Courbot <acourbot@nvidia.com>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Tested-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Acked-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Now that all[1] users of the gpiod_get functions are converted to make
use of the up to now optional flags parameter, make it mandatory which
allows to remove some cpp magic.

[1] all but etraxfs-uart which is broken anyhow and I'm allowed to
    ignore it by Jesper Nilsson :-)
Acked-by: NAlexandre Courbot <acourbot@nvidia.com>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>

There have been concerns that the function names gpiod_set_array() and
gpiod_get_array() might be confusing to users. One might expect
gpiod_get_array() to return array values, while it is actually the array
counterpart of gpiod_get(). To be consistent with the single descriptor API
we could rename gpiod_set_array() to gpiod_set_array_value(). This makes
some function names a bit lengthy: gpiod_set_raw_array_value_cansleep().
Signed-off-by: NRojhalat Ibrahim <imr@rtschenk.de>
Acked-by: NAlexandre Courbot <acourbot@nvidia.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

If GPIOLIB=n:

    drivers/leds/leds-gpio.c: In function ‘gpio_leds_create’:
    drivers/leds/leds-gpio.c:187: error: implicit declaration of function ‘devm_get_gpiod_from_child’
    drivers/leds/leds-gpio.c:187: warning: assignment makes pointer from integer without a cast

Add dummies for fwnode_get_named_gpiod() and devm_get_gpiod_from_child()
for the !GPIOLIB case to fix this.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Fixes: 40b73183 ("gpio: Support for unified device properties interface")
Acked-by: NAlexandre Courbot <acourbot@nvidia.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NBryan Wu <cooloney@gmail.com>

Passing a fixed base in struct gpio_chip is done for legacy
systems that cannot handle dynamic allocation. Discourage this
behaviour in the kerneldoc.
Acked-by: NAlexandre Courbot <acourbot@nvidia.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Clean up chained handler and handler data if they were set by
gpiochip_set_chained_irqchip().
Signed-off-by: NDmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Remove gpiod_sysfs_set_active_low (and gpio_sysfs_set_active_low) which
allowed code to change the polarity of a gpio line even after it had
been exported through sysfs.

Drivers should not care, and generally does not know, about gpio-line
polarity which is a hardware feature that needs to be described by
firmware.

It is currently possible to define gpio-line polarity in device-tree and
acpi firmware or using platform data. Userspace can also change the
polarity through sysfs.

Note that drivers using the legacy gpio interface could still use
GPIOF_ACTIVE_LOW to change the polarity before exporting the gpio.

There are no in-kernel users of this interface.

Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Harry Wei <harryxiyou@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-doc@vger.kernel.org
Cc: linux-kernel@zh-kernel.org
Cc: linux-arch@vger.kernel.org
Signed-off-by: NJohan Hovold <johan@kernel.org>
Reviewed-by: NAlexandre Courbot <acourbot@nvidia.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Clean gpio-chip class device registration and deregistration.

The class device is registered when a gpio-chip is added (or from
gpiolib_sysfs_init post-core init call), and deregistered when the chip
is removed.

Store the class device in struct gpio_chip directly rather than do a
class-device lookup on deregistration. This also removes the need for
the exported flag.
Signed-off-by: NJohan Hovold <johan@kernel.org>
Reviewed-by: NAlexandre Courbot <acourbot@nvidia.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

These functions do not belong in <asm-generic/gpio.h> since the
split into separate GPIO headers under <linux/gpio/*>. Move them
to <linux/gpio/driver.h> as is apropriate.
Acked-by: NAlexandre Courbot <acourbot@nvidia.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Add device managed variants of gpiod_get_array() / gpiod_put_array()
functions for conveniently obtaining and disposing of an entire array
of GPIOs with one function call.
Signed-off-by: NRojhalat Ibrahim <imr@rtschenk.de>
Reviewed-by: NAlexandre Courbot <acourbot@nvidia.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>