The sama5d36ek CMP board is the variant of sama5d3xek board.
It is equipped with the low-power DDR2 SDRAM, PMIC ACT8865 and
some power rail. Its main purpose is used to measure the power
consumption.
The difference of the sama5d36ek CMP dts from sama5d36ek dts is
listed as below.
 1. The USB host nodes are removed, that is, the USB host is disabled.
 2. The gpio_keys node is added to wake up from the sleep.
 3. The LCD isn't supported due to the pins for LCD are conflicted
    with gpio_keys.
 4. The adc0 node support the pinctrl sleep state to fix the over
    consumption on VDDANA.

As said in errata, "When the USB host ports are used in high speed
mode (EHCI), it is not possible to suspend the ports if no device is
attached on each port. This leads to increased power consumption even
if the system is in a low power mode." That is why the the USB host
is disabled.
Signed-off-by: NWenyou Yang <wenyou.yang@atmel.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Added basic dts support for MicroZed board.

- UART
- SDHCI
- Ethernet

Cc: Soren Brinkmann <soren.brinkmann@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: NJagan Teki <jteki@openedev.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

This machine is an open hardware router by cz.nic driven by a
Marvell Armada 385.
Signed-off-by: NUwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: NTomas Hlavacek <tmshlvck@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

Add the initial  device tree for the R8A7745 SoC based SK-RZG1E board.
The board has 1  debug  serial  port (SCIF2); include support for it,
so that the serial console can  work.

Based on the original (and large) patch by Dmitry Shifrin
<dmitry.shifrin@cogentembedded.com>.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add the initial device  tree for the R8A7743 SoC based SK-RZG1M board.
The board has one debug serial port (SCIF0); include support for it, so
that  the serial  console  can work.

Based on the original (and large) patch by Dmitry Shifrin
<dmitry.shifrin@cogentembedded.com>.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

The AM571x-IDK board is a board based on TI's AM5718 SOC
which has a single core 1.5GHz A15 processor. This board is a
development platform for the Industrial market with:
- 1GB of DDR3L
- Dual 1Gbps Ethernet
- HDMI,
- PRU-ICSS
- uSD
- 16GB eMMC
- CAN
- RS-485
- PCIe
- USB3.0
- Video Input Port
- Industrial IO port and expansion connector

The link to the data sheet and TRM can be found here:

http://www.ti.com/product/AM5718

Initial support is only for basic peripherals.
Signed-off-by: NSchuyler Patton <spatton@ti.com>
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NDave Gerlach <d-gerlach@ti.com>
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The CHIP Pro is a small embeddable board. It features a GR8, an AXP209
PMIC, a 512MB SLC NAND and a WiFi/BT chip.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NChen-Yu Tsai <wens@csie.org>

Reviews have found that sun5i was a better prefix after all for the GR8.
Rename the relevant device trees before it's too late.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This patch converts my orion5x ls-chl Linkstation device to device tree.

[gregory.clement@free-electrons.com: fix title, add back the commit log,
move the removal of the platform in an other patch]
Signed-off-by: NAshley Hughes <ashley.hughes@blueyonder.co.uk>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

Add support for the Sierra Wireless MangOH Green board with the
Sierra Wireless WP8548 Module.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NAndy Gross <andy.gross@linaro.org>

It's BCM4709A0 based device with 16 MiB flash, 128 MiB of RAM and two
PCIe based on-PCB BCM4360 chipsets.
Signed-off-by: NRafał Miłecki <rafal@milecki.pl>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

RK1108 EVB is designed by Rockchip for CVR field.
This patch add basic support for it, which can boot with
initramfs into shell.
Signed-off-by: NAndy Yan <andy.yan@rock-chips.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

Let's add minimal support for droid 4 with MMC and WLAN working.
It can be booted with appended dtb using kexec to a state where
MMC and WLAN work with currently no support for it's PMIC or
display.

Note that we are currently using fixed regulators as we don't
have support for it's cpcap PMIC. I'll be posting regmap_spi
based minimal cpcap patches later on for USB and the debug
UART on droid 4 multiplexed with the USB connector.

Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The STMicrolectornics's STM32F746 MCU has the following main features:
 - Cortex-M7 core running up to @216MHz
 - 1MB internal flash, 320KBytes internal RAM (+4KB of backup SRAM)
 - FMC controller to connect SDRAM, NOR and NAND memories
 - Dual mode QSPI
 - SD/MMC/SDIO support
 - Ethernet controller
 - USB OTFG FS & HS controllers
 - I2C, SPI, CAN busses support
 - Several 16 & 32 bits general purpose timers
 - Serial Audio interface
 - LCD controller
 - HDMI-CEC
 - SPDIFRX
Signed-off-by: NAlexandre TORGUE <alexandre.torgue@st.com>

It is the 10th processor in the well-known imx6 series, and derived
from imx6ul but cost optimized. The more information about imx6ull
can be found at:

http://www.nxp.com/products/microcontrollers-and-processors/
arm-processors/i.mx-applications-processors/i.mx-6-processors
/i.mx6qp/i.mx-6ull-single-core-processor-with-arm-cortex-a7-core
:i.MX6ULL

imx6ul.dtsi is the SoC common stuff for both imx6ul and imx6ull;
imx6ul-14x14-evk.dts is the board common stuff for both imx6ul
and imx6ull 14x14 evk. In this patch, for SoC part, the
imx6ull.dtsi includes imx6ul.dtsi; for board part, imx6ull-14x14-evk.dts
includes imx6ul-14x14-evk.dts.
Signed-off-by: NPeter Chen <peter.chen@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The DRA718-evm is a board based on TI's DRA718 processor targeting
BOM-optimized entry infotainment systems and is a reduced pin and
software compatible derivative of the DRA72 ES2.0 processor.
This platform features:
- 2GB of DDR3L
- Dual 1Gbps Ethernet
- HDMI,
- uSD
- 8GB eMMC
- CAN
- PCIe
- USB3.0
- Video Input Port
- LP873x PMIC

More information can be found here[1].

Adding support for this board while reusing the data available in
dra72-evm-common.dtsi.

[1] http://www.ti.com/product/dra718Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NKeerthy <j-keerthy@ti.com>
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Enable the QSPI node and add the flash chip.
Signed-off-by: NDinh Nguyen <dinguyen@opensource.altera.com>

Add device tree for the Oxford Seminconductor OX820 SoC and the
Cloud Engines PogoPlug v3 board.
Add the SoC and board compatible strings to oxnas bindings.
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>

SoM based on i.MX6 Quad with 1GB of DDR3.

https://boundarydevices.com/product/nit6x-som-v2/Signed-off-by: NGary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

i.CoreM6 DualLite/Solo modules are system on module solutions manufactured
by Engicam with following characteristics:
CPU           NXP i.MX6 DL, 800MHz
RAM           1GB, 32, 64 bit, DDR3-800/1066
NAND          SLC,512MB
Power supply  Single 5V
MAX LCD RES   FULLHD

and more info at
http://www.engicam.com/en/products/embedded/som/sodimm/i-core-m6s-dl-d-q

Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

i.CoreM6 Quad/Dual modules are system on module solutions manufactured
by Engicam with following characteristics:
CPU           NXP i.MX6 DQ, 800MHz
RAM           1GB, 32, 64 bit, DDR3-800/1066
NAND          SLC,512MB
Power supply  Single 5V
MAX LCD RES   FULLHD

and more info at
http://www.engicam.com/en/products/embedded/som/sodimm/i-core-m6s-dl-d-q

Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

liteBoard is a development board which uses liteSOM as its base.

Hardware specification:
 * liteSOM (i.MX6UL, DRAM, eMMC)
 * Ethernet PHY (id 0)
 * USB host (usb_otg1)
 * MicroSD slot (uSDHC1)
Signed-off-by: NMarcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Add initial device trees for UDOO Neo Basic, Extended and Full boards:
* Serial console is enabled, other serial ports are prepared.
* I2C based PMIC is enabled.
* Ethernet is enabled for Basic and Full.
* SDHC is enabled, with the SDIO_PWR GPIO modeled as a regulator.
* Both user LEDs are enabled, with the orange one reserved for the M4
  and with the SD card as default trigger for the red LED.

The decision on a board compatible string is deferred to later.

Cc: Ettore Chimenti <ettore.chimenti@udoo.org>
Signed-off-by: NAndreas Färber <afaerber@suse.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Add support for Toradex Colibri iMX6 module.
Signed-off-by: NSanchayan Maity <maitysanchayan@gmail.com>
Acked-by: NMarcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

MK808 is a tv stick which has rockchip rk3066 CPU inside, two usb ports
- host and otg, micro sd card slot and onboard wifi RK901.
Signed-off-by: NPaweł Jarosz <paweljarosz3691@gmail.com>
Reviewed-by: NShawn Lin <shawn.lin@rock-chip.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

Since v4.8, STiH415/416 clock support has
been removed [1], these platform doesn't boot.
We can remove DTS files related to these socs.

[1] https://patchwork.kernel.org/patch/9157571/Signed-off-by: NPatrice Chotard <patrice.chotard@st.com>

Since v4.8, STiH415/416 clock support has
been removed [1], these platform doesn't boot.
We can remove DTS files related to these socs.

[1] https://patchwork.kernel.org/patch/9157571/Signed-off-by: NPatrice Chotard <patrice.chotard@st.com>

Since v4.8, STiH415/416 clock support has
been removed [1], these platform doesn't boot.
We can remove DTS files related to these socs.

[1] https://patchwork.kernel.org/patch/9157571/Signed-off-by: NPatrice Chotard <patrice.chotard@st.com>

Since v4.8, STiH415/416 clock support has
been removed [1], these platform doesn't boot.
We can remove DTS files related to these socs.

[1] https://patchwork.kernel.org/patch/9157571/Signed-off-by: NPatrice Chotard <patrice.chotard@st.com>

Since v4.8, STiH415/416 clock support has
been removed [1], these platform doesn't boot.
We can remove DTS files related to these socs.

[1] https://patchwork.kernel.org/patch/9157571/Signed-off-by: NPatrice Chotard <patrice.chotard@st.com>

Luxul XWR-3100 is a wireless router based on BCM47094 SoC with two
4366c0 FullMAC PCIe cards on the PCB. It uses NAND with BCH-4 ECC
algorithm.
Signed-off-by: NDan Haab <dhaab@luxul.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

Luxul XAP-1510 is an AP device based on BCM4708 SoC with 2 x BCM4360
chipsets on PCB connected using PCIe.
Signed-off-by: NDan Haab <dhaab@luxul.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

BCM53573 seems to be low priced alternative for Northstar chipsts. It
uses single core Cortex-A7 and doesn't have SDU or local (TWD) timer. It
was also stripped out of independent SPI controller and 2 GMACs.

DTS for Tenda AC9 isn't completed yet. It misses e.g. switch entry (we
still need some b53 fixes) and probably some clocks. It adds support for
basic features however and can be improved later.
Signed-off-by: NRafał Miłecki <rafal@milecki.pl>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

Netgear R8500 is another BCM47094 device, it just has three BCM4366
wireless chipsets. It's a very standard DT with mostly GPIO devices.
Signed-off-by: NRafał Miłecki <rafal@milecki.pl>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>

Add support for board based on the Altera Cyclone V SoC.
This board has the following functions:
    - 1 GiB of DRAM
    - 1 Gigabit ethernet
    - 1 SD card slot
    - 1 USB gadget port
    - QSPI NOR Flash
    - I2C EEPROMs and I2C RTC
    - DVI output
    - Audio port

This commit supports without QSPI, DVI and Audio.
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: NDinh Nguyen <dinguyen@opensource.altera.com>

The TOPEET itop Exynos4412 has three versions of base boards. The
Elite version is the cheap one without too much peripheral devices
on it.

Currently supported are serial console, wired networking (USB), USB OTG
in peripheral mode, USB host, SD storage, GPIO buttons, PWM beeper, ADC
and LEDs. The WM8960 analog audio codec is also enabled.

The FIMC is not used for camera currently, I enabled it just for a
colorspace converter.
Signed-off-by: NRandy Li <ayaka@soulik.info>
Acked-by: NRob Herring <robh@kernel.org>
[krzk: fixup pin function macro, adjust commit msg]
Signed-off-by: NKrzysztof Kozlowski <krzk@kernel.org>

PX3 EVB is designed by Rockchip for automotive field,
with integrated CVBS (TP2825) / MIPI DSI / LVDS / HDMI
video input/output interface, WIFI/BT/GPS (on a module
named S500 which based on MT6620), Gsensor BMA250E and
light&proximity sensor STK3410.
Signed-off-by: NAndy Yan <andy.yan@rock-chips.com>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

This is a router based on the mv88f5181 chipset.

http://www.netgear.com/support/product/WNR854T.aspx
http://wiki.openwrt.org/toh/netgear/wnr854t

[gregory.clement@free-electrons.com:
- extract dt part from "arm: orion5x: Add DT-based support for Netgear
  WNR854T"
- squashed "arm: orion5x: Alias uart0 to serial0 for all orion5x" into
this commit and move serial0 alias from dtsi to dts]
Signed-off-by: NJamie Lentin <jm@lentin.co.uk>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

Latest update to the BeagleBoard-X15 platform (revision B1)[1] updates
for allowing UHS SD cards to function with the split of supply to SD
card from a dedicated LDO.

As a result of this, AM57xx BeagleBoard-X15 now uses gpio2_30 instead
of gpio6_28 for HDMI because HDMI_LS_OE should now be switched from
GPIO6_28(Y9) to GPIO2_30 (AG8) to avoid a 1.8V GPIO toggling a 3.3V
SoC input when the SD card is in UHS 1.8V mode.

NOTE: For UHS mode to function, we need full fledged IODelay support
in kernel to be functional. IODelay support is yet to be added.

Further, It does not make much sense to spin off a new board
compatible flag since there is no real functional benefit for the
same.

Note: Even though production version is supposed to be B1, there is
over ~200 boards of previous version (A2)[2] out there which continue
to get supported with the existing dts file (to maintain compatibility
with existing bootloaders for A2) and the production board is now
supported as revb1.

[1] https://github.com/beagleboard/beagleboard-x15/blob/master/BEAGLEBOARD_X15_REV_B1.pdf
[2] http://marc.info/?l=linux-arm-kernel&m=147273929820708&w=2Tested-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The GR8-EVB is a small board with an NextThing GR8, an Hynix MLC NAND,
an AXP209 PMIC, USB host and OTG, an SPDIF output and a connectors for CSI,
I2S and LCD.
Signed-off-by: NMylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NChen-Yu Tsai <wens@csie.org>