track_id == 0 is valid for “read only” profiles when
profile does not have any “write” commands.
Signed-off-by: NJingjing Wu <jingjing.wu@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

PPP name was going to be confusing since PPP already means point
to point protocol. It is decided to change pipeline personalization
profile(ppp) to dynamic device personalization(ddp).
Signed-off-by: NJingjing Wu <jingjing.wu@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch allows detection of upcoming core reset in case NIC gets
stuck while performing FLR reset. The i40e_pf_reset() function returns
I40E_ERR_NOT_READY when global reset was detected.
Signed-off-by: NFilip Sadowski <filip.sadowski@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Since commit 96a39aed ("i40e: Acquire NVM lock before
reads on all devices") we've used the NVM lock
to synchronize NVM reads even on devices which don't strictly
need the lock.

Doing so can cause a regression on older firmware prior to 1.5,
especially when downgrading the firmware.

Fix this by only grabbing the lock if we're running on an X722
device (which requires the lock as it uses the AdminQ to read
the NVM), or if we're currently running 1.5 or newer firmware.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch enables tc-flower based hardware offloads. tc flower
filter provided by the kernel is configured as driver specific
cloud filter. The patch implements functions and admin queue
commands needed to support cloud filters in the driver and
adds cloud filters to configure these tc-flower filters.

The classification function of the filter is to direct matched
packets to a traffic class. The hardware traffic class is set
based on the the classid reserved in the range :ffe0 - :ffef.

Match Dst MAC and route to TC0:
  prio 1 flower dst_mac 3c:fd:fe:a0:d6:70 skip_sw\
  hw_tc 1

Match Dst IPv4,Dst Port and route to TC1:
  prio 2 flower dst_ip 192.168.3.5/32\
  ip_proto udp dst_port 25 skip_sw\
  hw_tc 2

Match Dst IPv6,Dst Port and route to TC1:
  prio 3 flower dst_ip fe8::200:1\
  ip_proto udp dst_port 66 skip_sw\
  hw_tc 2

Delete tc flower filter:
Example:

Flow Director Sideband is disabled while configuring cloud filters
via tc-flower and until any cloud filter exists.

Unsupported matches when cloud filters are added using enhanced
big buffer cloud filter mode of underlying switch include:
1. source port and source IP
2. Combined MAC address and IP fields.
3. Not specifying L4 port

These filter matches can however be used to redirect traffic to
the main VSI (tc 0) which does not require the enhanced big buffer
cloud filter support.
Signed-off-by: NAmritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: NKiran Patil <kiran.patil@intel.com>
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: NJingjing Wu <jingjing.wu@intel.com>
Acked-by: NShannon Nelson <shannon.nelson@oracle.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add definitions for L4 filters and switch modes based on cloud filters
modes and extend the set switch config command to include the
additional cloud filter mode.
Signed-off-by: NAmritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: NKiran Patil <kiran.patil@intel.com>
Acked-by: NShannon Nelson <shannon.nelson@oracle.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support for 25G Active Optical Cables (AOC) and Active
Copper Cables (ACC) PHY types.
Signed-off-by: NSudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Signed-off-by: NKrzysztof Malek <krzysztof.malek@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When querying the NVM for supported phy_types, on some firmware
versions, we were failing to actually fill out the phy_types which means
ethtool wouldn't report any link types.

Testing-hints:
Check 'ethtool <iface>' if you have the right (wrong?) firmware.
Without this patch, no link modes will be reported.
Signed-off-by: NAlan Brady <alan.brady@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

- When the I2C is busy, the PHY reads are delayed.  The firmware will
  return EGAIN in these cases with an expectation that the SW will
  trigger the reads again
- This patch retries the operation for a maximum period of 500ms
Signed-off-by: NJayaprakash Shanmugam <jayaprakash.shanmugam@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Enable i40e to pass traffic with VLAN tags using the 802.1ad ethernet
protocol ID (0x88a8).

This requires NIC firmware providing version 1.7 of the API. With
older NIC firmware 802.1ad tagged packets will continue to be dropped.

No VLAN offloads nor RSS are supported for 802.1ad VLANs.
Signed-off-by: NScott Peterson <scott.d.peterson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Instead of accessing register directly, use newly added AQC in
order to blink LEDs. Introduce and utilize a new flag to prevent
excessive API version checking.
Signed-off-by: NMariusz Stachura <mariusz.stachura@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support for 'ethtool -m' command which displays
information about (Q)SFP+ module plugged into NIC's cage.
Signed-off-by: NFilip Sadowski <filip.sadowski@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes incorrect reporting of supported link modes on some NICs.
Signed-off-by: NFilip Sadowski <filip.sadowski@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The i40e driver now supports two different devices with two different
firmware versions. So be smart about how we handle these. Move the FW
version macros to the appropriate header file, and add a convenience
macro that checks the version based on the device. Then use this macro
to check whether or not the driver can use the new link info API.
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Increase the size of the prefix buffer so that it can hold enough
characters for every possible input. Although 20 is enough for all
expected inputs, it is possible for the values to be larger than
expected, resulting in a possibly truncated string. Additionally, lets
use sizeof(prefix) in order to ensure we use the correct size if we need
to change the array length in the future.

New versions of GCC starting at 7 now include warnings to prevent
truncation unless you handle the return code. At most 27 bytes can be
written here, so lets just increase the buffer size even if for all
expected hw->bus.* values we only needed 20.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Store information about FEC modes, that were requested. It will be used
in printing link status information function and this way there is no
need to call admin queue there.
Signed-off-by: NMariusz Stachura <mariusz.stachura@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The firmware expects the port number passed when setting up
the UDP tunnel configuration to be in Little Endian format.
The i40e_aq_add_udp_tunnel command byte swaps the value from
host order to Little Endian.

Since commit fe0b0cd9 ("i40e: send correct port number to
AdminQ when enabling UDP tunnels") we've correctly
sent the value in host order.

Let's also add a comment to the function explaining that it must
be in host order, as the port numbers are commonly stored as Big
Endian values.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch changes the i40e driver to start using the new virtchnl
interface header file, and removes an already existing duplicate of the
i40e_virtchnl.h file contained in the i40e directory.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add admin queue functions for Pipeline Personalization Profile AQ
commands:
 - Write Recipe Command buffer (Opcode: 0x0270)
 - Get Applied Profiles list (Opcode: 0x0271)

Change-ID: I558b4145364140f624013af48d4bbf79d21ebb0d
Signed-off-by: NJingjing Wu <jingjing.wu@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The XL722 doesn't support the AQ command to read/write the control
register so enable it to bypass the check and use the direct read/write
method.

Change-ID: Iefecc737b57207485c90845af5989d5af518bf16
Signed-off-by: NPaul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Looking over the code for FCoE it looks like the Rx path has been broken at
least since the last major Rx refactor almost a year ago.  It seems like
FCoE isn't supported for any of the Fortville/Fortpark hardware so there
isn't much point in carrying the code around, especially if it is broken
and untested.

Change-ID: I892de8fa551cb129ce2361e738ff82ce55fa229e
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch refactors the '%*ph' printk format specifier to instead use
the print_hex_dump function, as recommended by the '%*ph' documentation.
This produces better/more standardized output.

Change-ID: Id56700b4e8abc40ff8c04bc8379e7df04cb4d6fd
Signed-off-by: NAlan Brady <alan.brady@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Store the FEC status bits from the link up event into the
hw_link_info structure.

Change-ID: I9a7b256f6dfb0dce89c2f503075d0d383526832e
Signed-off-by: NHenry Tieman <henry.w.tieman@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Depending on external PHY type, register access method should be
different. Clause22 or Clause45 can be chosen for different PHYs.
Implemented functions apply correct access method for used device.

Change-ID: If39d5f0da9c0b905a8cbdc1ab89885535e7d0426
Signed-off-by: NMichal Kosiarz <michal.kosiarz@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds adminq support for Forward Error
Correction ("FEC")for 25g products.

Change-ID: Iaff4910737c239d2c730e5c22a313ce9c37d3964
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NJacek Naczyk <jacek.naczyk@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add support for 25G devices - defines and data structures.

One tricky part here is that the firmware support for these
Devices introduces a mismatch between the PHY type enum and
the bitfields for the phy types.

This change creates a macro and uses it to increment the 25G
PHY values when creating 25G bitfields.

Change-ID: I69b24d837d44cf9220bf5cb8dd46c5be89ce490b
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

A previous workaround added to ensure receipt of all broadcast frames
incorrectly set the broadcast promiscuous mode unconditionally
regardless of active VLAN status.

Replace this partial workaround with a complete solution that sets the
broadcast promiscuous filters in i40e_sync_vsi_filters. This new method
sets the promiscuous mode based on when broadcast filters are added or
removed.

I40E_VLAN_ANY will request a broadcast filter for all VLANs, (as we're
in untagged mode) while a broadcast filter on a specific VLAN will only
request broadcast for that VLAN.

Thus, we restore addition of broadcast filter to the array, but we add
special handling for these such that they enable the broadcast
promiscuous mode instead of being sent as regular filters.

The end result is that we will correctly receive all broadcast packets
(even those with a *source* address equal to the broadcast address) but
will not receive packets for which we don't have an active VLAN filter.

Change-ID: I7d0585c5cec1a5bf55bf533b42e5e817d5db6a2d
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The PHY type value for unrecognized PHYs and cables was changed
based on firmware version number. Newer hardware use lower firmware
version numbers and this was causing some PHYs to be identified
as type 0x16 instead of 0xe (unknown).

Without this patch, newer card will incorrectly identify unknown
PHYs and cables.

This change adds hardware type to the check for firmware version
so the PHY type is reported correctly.

Change-ID: I0723cbfd263c76fc73ff1a5275d1639051376c9a
Signed-off-by: NHenry Tieman <henry.w.tieman@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The code at the end of i40e_read_phy_register_clause22() contained
unreachable code and redundant control statements.

This change removes the unreachable code. And deletes the redundant
goto statement and if statement.

Change-ID: I713032b1585396f40f903cbcfdea987abd874400
Signed-off-by: NHenry Tieman <henry.w.tieman@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add logical_id to I40E_AQ_CAP_ID_MNG_MODE capability starting from major
version 2.

Change-ID: Idb29214b172ea5c70cbd45a99e6745c0215af7e4
Signed-off-by: NPiotr Raczynski <piotr.raczynski@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Some external PHYs require Clause22 method for accessing registers.
This patch also adds some defines to support blink led on devices using
10CBaseT PHY.

Change-ID: I868a4326911900f6c89e7e522fda4968b0825f14
Signed-off-by: NMichal Kosiarz <michal.kosiarz@intel.com>
Signed-off-by: NMatt Jared <matthew.a.jared@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

For some cases when reading from device are incorrect or image is
incorrect, this part of code causes crash due to division by zero.

Change-ID: I8961029a7a87b0a479995823ef8fcbf6471405e1
Signed-off-by: NMichal Kosiarz <michal.kosiarz@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes a problem where it could take a very
long time (>100 msec) to print the link down notification.
This problem is fixed by changing how often we update link
info from fw, when link is down. Without this patch, it can
take over 100msec to notify user link is down.

Change-ID: Ib876eb30834c7080792becd13ee093b9cbb35d78
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Incorrect bit mask was used for testing "get link status" response.
Instead of I40E_AQ_LSE_ENABLE (which is actually 0x03) it most probably
should be I40E_AQ_LSE_IS_ENABLED (which is defined as 0x01).

Change-ID: Ia199142906720507f847de3a33a25c61a9781b2f
Signed-off-by: NFilip Sadowski <filip.sadowski@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This device ID is not needed, so take it out.

Change-ID: I148d29f68a1f58b03980ecd83047a1b440f4f74d
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In function i40e_debug_aq parameter desc is assumed to be
possibly NULL. Do not dereference it before checking the
value.

Fixes: f905dd62 ("i40e/i40evf: add max buf len to aq debug print helper")
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add functions to enable and disable default VSI on a VEB. This allows
for configuration of limited promiscuous mode specifically for bridging
purposes.

Change-ID: I0cc5bd68b31c500fdff4d47e1f15d50d2739faf4
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch corrects Rx ptype payload layer for non_tunneled ipv6. It
should be layer 4 for UDP, instead of layer 3.

Change-ID: I9382e4458ab3c4e58f6d2e9f195d5d4ee513805e
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds priv-flag knob to configure global true promisc
support. With this patch the user can decide the flavor of
promiscuous that the VFs will see when promiscuous mode is enabled
on the interface. Since this a global setting for the whole device,
the priv-flag is exposed only on the first PF of the device.

The default is true promisc support is off, which means the promisc
mode for the VF will be limited/defport mode.

For the PF, we still will be in limited promisc unless in MFP mode
irrespective of the flavor picked through this knob.

Usage:
On PF0
ethtool --show-priv-flags p261p1
Private flags for p261p1:
MFP                    : off
LinkPolling            : off
flow-director-atr      : on
veb-stats              : off
hw-atr-eviction        : off
vf-true-promisc-support: off

to enable setting true promisc
ethtool --set-priv-flags p261p1 vf-true-promisc-support on

At this point if the VF is set to trust and promisc is enabled
on the VF through
ip link set ... promisc on
The VF/VFs will be able to see ALL ingress traffic

Change-Id: I8fac4b6eb1af9ca77b5376b79c50bdce5055bd94
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add the support code for calling the AdminQ API call aq_set_switch_config
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>