[ Upstream commit d6ee1e7e9004d3d246cdfa14196989e0a9466c16 ]

Similar to gxbb and gxl platforms, axg SCPI Cortex-M co-processor
uses the fdiv2 and fdiv3 to, among other things, provide the cpu
clock.

Until clock hand-off mechanism makes its way to CCF and the generic
SCPI claims platform specific clocks, these clocks must be marked as
critical to make sure they are never disabled when needed by the
co-processor.

Fixes: 05f81440 ("clk: meson: add fdiv clock gates")
Signed-off-by: NJerome Brunet <jbrunet@baylibre.com>
Acked-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NStephen Boyd <sboyd@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit e2576c8bdfd462c34b8a46c0084e7c30b0851bf4 ]

On the Khadas VIM2 (GXM) and LePotato (GXL) board there are problems
with reboot; e.g. a ~60 second delay between issuing reboot and the
board power cycling (and in some OS configurations reboot will fail
and require manual power cycling).

Similar to 'commit c987ac6f ("clk:
meson-gxbb: set fclk_div2 as CLK_IS_CRITICAL")' the SCPI Cortex-M4
Co-Processor seems to depend on FCLK_DIV3 being operational.

Until commit 05f81440 ("clk:
meson: add fdiv clock gates"), this clock was modeled and left on by
the bootloader.

We don't have precise documentation about the SCPI Co-Processor and
its clock requirement so we are learning things the hard way.

Marking this clock as critical solves the problem but it should not
be viewed as final solution. Ideally, the SCPI driver should claim
these clocks. We also depends on some clock hand-off mechanism
making its way to CCF, to make sure the clock stays on between its
registration and the SCPI driver probe.

Fixes: 05f81440 ("clk: meson: add fdiv clock gates")
Signed-off-by: NChristian Hewitt <christianshewitt@gmail.com>
Signed-off-by: NJerome Brunet <jbrunet@baylibre.com>
Signed-off-by: NStephen Boyd <sboyd@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

commit fd5ba6ee3187617287fb9cb187e3d6b3631210a3 upstream

On Stratix 10, the EMAC has 256 hash buckets for multicast filtering. This
needs to be specified in DTS, otherwise the stmmac driver defaults to 64
buckets and initializes the filter incorrectly. As a result, e.g. valid
IPv6 multicast traffic ends up being dropped.

Fixes: 78cd6a9d ("arm64: dts: Add base stratix 10 dtsi")
Cc: stable@vger.kernel.org
Signed-off-by: NAaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: NDinh Nguyen <dinguyen@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

commit a27460c9768ee19949c5b91f3d959ccd88c2a64a upstream

Properly specify the RX and TX FIFO size which is important
for Jumbo frames.
Update the max-frame-size to support Jumbo frames.
Signed-off-by: NThor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

commit f9a7082327e26f54067a49cac2316d31e0cc8ba7 upstream.

Use the new of_get_compatible_child() helper to lookup the legacy
pwrlevels child node instead of using of_find_compatible_node(), which
searches the entire tree from a given start node and thus can return an
unrelated (i.e.  non-child) node.

This also addresses a potential use-after-free (e.g. after probe
deferral) as the tree-wide helper drops a reference to its first
argument (i.e. the probed device's node).

While at it, also fix the related child-node reference leak.

Fixes: e2af8b6b ("drm/msm: gpu: Use OPP tables if we can")
Cc: stable <stable@vger.kernel.org>     # 4.12
Cc: Jordan Crouse <jcrouse@codeaurora.org>
Cc: Rob Clark <robdclark@gmail.com>
Cc: David Airlie <airlied@linux.ie>
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NRob Herring <robh@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 4c316f2f3ff315cb48efb7435621e5bfb81df96d upstream.

Otherwise fuse_dev_do_write() could come in and finish off the request, and
the set_bit(FR_SENT, ...) could trigger the WARN_ON(test_bit(FR_SENT, ...))
in request_end().
Signed-off-by: NMiklos Szeredi <mszeredi@redhat.com>
Reported-by: syzbot+ef054c4d3f64cd7f7cec@syzkaller.appspotmai
Fixes: 46c34a34 ("fuse: no fc->lock for pqueue parts")
Cc: <stable@vger.kernel.org> # v4.2
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 908a572b80f6e9577b45e81b3dfe2e22111286b8 upstream.

Using waitqueue_active() is racy.  Make sure we issue a wake_up()
unconditionally after storing into fc->blocked.  After that it's okay to
optimize with waitqueue_active() since the first wake up provides the
necessary barrier for all waiters, not the just the woken one.
Signed-off-by: NMiklos Szeredi <mszeredi@redhat.com>
Fixes: 3c18ef81 ("fuse: optimize wake_up")
Cc: <stable@vger.kernel.org> # v3.10
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d2d2d4fb1f54eff0f3faa9762d84f6446a4bc5d0 upstream.

After we found req in request_find() and released the lock,
everything may happen with the req in parallel:

cpu0                              cpu1
fuse_dev_do_write()               fuse_dev_do_write()
  req = request_find(fpq, ...)    ...
  spin_unlock(&fpq->lock)         ...
  ...                             req = request_find(fpq, oh.unique)
  ...                             spin_unlock(&fpq->lock)
  queue_interrupt(&fc->iq, req);   ...
  ...                              ...
  ...                              ...
  request_end(fc, req);
    fuse_put_request(fc, req);
  ...                              queue_interrupt(&fc->iq, req);
Signed-off-by: NKirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: NMiklos Szeredi <mszeredi@redhat.com>
Fixes: 46c34a34 ("fuse: no fc->lock for pqueue parts")
Cc: <stable@vger.kernel.org> # v4.2
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit bc78abbd55dd28e2287ec6d6502b842321a17c87 upstream.

We may pick freed req in this way:

[cpu0]                                  [cpu1]
fuse_dev_do_read()                      fuse_dev_do_write()
   list_move_tail(&req->list, ...);     ...
   spin_unlock(&fpq->lock);             ...
   ...                                  request_end(fc, req);
   ...                                    fuse_put_request(fc, req);
   if (test_bit(FR_INTERRUPTED, ...))
         queue_interrupt(fiq, req);

Fix that by keeping req alive until we finish all manipulations.

Reported-by: syzbot+4e975615ca01f2277bdd@syzkaller.appspotmail.com
Signed-off-by: NKirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: NMiklos Szeredi <mszeredi@redhat.com>
Fixes: 46c34a34 ("fuse: no fc->lock for pqueue parts")
Cc: <stable@vger.kernel.org> # v4.2
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 8f97d1e9 upstream.

Some anon_bdev filesystems (e.g. overlayfs, ceph) don't have s_blocksize
set. Returning zero from FIGETBSZ ioctl results in a Floating point
exception from the e2fsprogs utility filefrag, which divides the size of
the file with the value returned by FIGETBSZ.

Fix the interface by returning -EINVAL for these filesystems.

Fixes: d1d04ef8 ("ovl: stack file ops")
Cc: <stable@vger.kernel.org> # v4.19
Signed-off-by: NAmir Goldstein <amir73il@gmail.com>
Signed-off-by: NMiklos Szeredi <mszeredi@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 39553065 upstream.

This patch fixes multiple call for qla_nvme_unregister_remote_port() as part
of qlt_schedule_session_for_deletion(), Do not call it again during
qla_nvme_delete()

Fixes: e473b307 ("scsi: qla2xxx: Add FC-NVMe abort processing")
Cc: <stable@vger.kernel.org>
Reviewed-by: NEwan D. Milne <emilne@redhat.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 732ee9a9 upstream.

The response data buffer used in switch scan is reused 4 times.  (For example,
for commands GPN_FT, GNN_FT for FCP and FC-NVME) Before driver reuses this
buffer, clear it to prevent duplicate entries in our database.

Fixes: a4239945 ("scsi: qla2xxx: Add switch command to simplify fabric discovery"
Cc: <stable@vger.kernel.org>
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Reviewed-by: NEwan D. Milne <emilne@redhat.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit db186382af21e926e90df19499475f2552192b77 upstream.

This patch fixes issue when remoteport registers itself as both FCP and
FC-NVMe with the switch, driver will pick FC-NVMe personality as default when
scanning for targets.

Driver was using comaprative operator instead of bitwise operator to check for
fc4_type for both FCP and FC-NVME.

Fixes: 2b5b9647 ("scsi: qla2xxx: Fix FC-NVMe LUN discovery")
Cc: <stable@vger.kernel.org>
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Reviewed-by: NEwan D. Milne <emilne@redhat.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f7d61c99 upstream.

Send aborts only when chip is active.

Fixes: 623ee824 ("scsi: qla2xxx: Fix FC-NVMe IO abort during driver reset")
Cc: <stable@vger.kernel.org> # 4.14
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Reviewed-by: NEwan D. Milne <emilne@redhat.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit bcc71cc3cde1468958a3ea859276d8d1a1a68265 upstream.

This patch fixes issue during switch command query where driver was freeing
SRB resources multiple times

Following stack trace will be seen
[  853.436234] BUG: unable to handle kernel NULL pointer dereference at
0000000000000001
[  853.436348] IP: [<ffffffff811df514>] kmem_cache_alloc+0x74/0x1e0
[  853.436476] PGD 0
[  853.436601] Oops: 0000 [#1] SMP

[  853.454700]  [<ffffffff81099f6a>] ? mod_timer+0x14a/0x220
[  853.455543]  [<ffffffff81185465>] mempool_alloc_slab+0x15/0x20
[  853.456395]  [<ffffffff811855a9>] mempool_alloc+0x69/0x170
[  853.457257]  [<ffffffff81098af2>] ? internal_add_timer+0x32/0x70
[  853.458136]  [<ffffffffc0092d2b>] qla2xxx_queuecommand+0x29b/0x3f0 [qla2xxx]
[  853.459024]  [<ffffffff8146535a>] scsi_dispatch_cmd+0xaa/0x230
[  853.459923]  [<ffffffff8146e11f>] scsi_request_fn+0x4df/0x680
[  853.460829]  [<ffffffff81029557>] ? __switch_to+0xd7/0x510
[  853.461747]  [<ffffffff812f7113>] __blk_run_queue+0x33/0x40
[  853.462670]  [<ffffffff812f7735>] blk_delay_work+0x25/0x40
[  853.463603]  [<ffffffff810a882a>] process_one_work+0x17a/0x440
[  853.464546]  [<ffffffff810a94f6>] worker_thread+0x126/0x3c0
[  853.465501]  [<ffffffff810a93d0>] ? manage_workers.isra.24+0x2a0/0x2a0
[  853.466447]  [<ffffffff810b099f>] kthread+0xcf/0xe0
[  853.467379]  [<ffffffff810b08d0>] ? insert_kthread_work+0x40/0x40
[  853.470172] Code: db e2 7e 49 8b 50 08 4d 8b 20 49 8b 40 10 4d 85 e4 0f 84 20
01 00 00 48 85 c0 0f 84 17 01 00 00 49 63 46 20 48 8d 4a 01 4d 8b 06 <49> 8b 1c
04 4c 89 e0 65 49 0f c7 08 0f 94 c0 84 c0 74 ba 49 63
[  853.472072] RIP  [<ffffffff811df514>] kmem_cache_alloc+0x74/0x1e0
[  853.472971]  RSP <ffff88103726fc50>

Fixes: 726b8548 ("qla2xxx: Add framework for async fabric discovery")
Cc: <stable@vger.kernel.org>
Signed-off-by: NGiridhar Malavali <giridhar.malavali@cavium.com>
Reviewed-by: NEwan D. Milne <emilne@redhat.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 5c640053 upstream.

This patch fixes issue where driver clears NPort ID map instead of marking
handle in use. Once driver clears NPort ID from the database, it can reuse
the same NPort ID resulting in a PLOGI failure.

[mkp: fixed Himanshu's SoB]

Fixes: a084fd68 ("scsi: qla2xxx: Fix re-login for Nport Handle in use")
Cc: <stable@vger.kernel.org>
Signed-of-by: NQuinn Tran <quinn.tran@cavium.com>
Reviewed-by: NEwan D. Milne <emilne@redhat.com>
Signed-off-by: NHimanshu Madhani <hmadhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 56d942de59ebfa2e970a6cd33299d1984710b6c0 upstream.

Reject bsg request if chip is down.  This prevent erroneous timeout.

Fixes: d051a5aa ("[SCSI] qla2xxx: Add an "is reset active" helper.")
Cc: stable@vger.kernel.org # 4.10
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 1e4ac5d6fe0a4af17e4b6251b884485832bf75a3 upstream.

If chip unable to fully initialize, use full shutdown sequence to clear out
any stale FW state.

Fixes: e315cd28 ("[SCSI] qla2xxx: Code changes for qla data structure refactoring")
Cc: stable@vger.kernel.org  #4.10
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 8235f4b5aeba868739f6e12a51ad92689e3f78ef upstream.

Task abort can take 2 paths: 1) serial/synchronous abort where the calling
thread will put to sleep, wait for completion and free cmd resource.  2) async
abort where the cmd free will be free by the completion thread.  For path 2,
driver is freeing the SRB too early.

Fixes: f6145e86 ("scsi: qla2xxx: Fix race between switch cmd completion and timeout")
Cc: stable@vger.kernel.org # 4.19
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 7c388f91ec1a59b0ed815b07b90536e2d57e1e1f upstream.

Remove stale debug trace.

Fixes: 1eb42f96 ("qla2xxx: Make trace flags more readable")
Cc: stable@vger.kernel.org #4.10
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit b86ac8fd4b2f6ec2f9ca9194c56eac12d620096f upstream.

This patch improves performance for 16G and above adapter by removing
additional call to process_response_queue().

[mkp: typo]

Cc: <stable@vger.kernel.org>
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 4c1458df9635c7e3ced155f594d2e7dfd7254e21 upstream.

Fixes: 6246b8a1 ("[SCSI] qla2xxx: Enhancements to support ISP83xx.")
Fixes: 1bb39548 ("qla2xxx: Correct iiDMA-update calling conventions.")
Cc: <stable@vger.kernel.org>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 641a41dbba217ee5bd26abe6be77f8cead9cd00e upstream.

This patch fixes an issue that the sci_remove() could not remove
dev_attr_rx_fifo_timeout because uart_remove_one_port() set
the port->port.type to PORT_UNKNOWN.
Reported-by: NHiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com>
Fixes: 5d23188a ("serial: sh-sci: make RX FIFO parameters tunable via sysfs")
Cc: <stable@vger.kernel.org> # v4.11+
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: NUlrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d47748e5 upstream.

Current behavior is to automatically disable metacopy if redirect_dir is
not enabled and proceed with the mount.

If "metacopy=on" mount option was given, then this behavior can confuse the
user: no mount failure, yet metacopy is disabled.

This patch makes metacopy=on imply redirect_dir=on.

The converse is also true: turning off full redirect with redirect_dir=
{off|follow|nofollow} will disable metacopy.

If both metacopy=on and redirect_dir={off|follow|nofollow} is specified,
then mount will fail, since there's no way to correctly resolve the
conflict.
Reported-by: NDaniel Walsh <dwalsh@redhat.com>
Fixes: d5791044 ("ovl: Provide a mount option metacopy=on/off...")
Cc: <stable@vger.kernel.org> # v4.19
Signed-off-by: NMiklos Szeredi <mszeredi@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 5e1275808630ea3b2c97c776f40e475017535f72 upstream.

Kaixuxia repors that it's possible to crash overlayfs by removing the
whiteout on the upper layer before creating a directory over it.  This is a
reproducer:

 mkdir lower upper work merge
 touch lower/file
 mount -t overlay overlay -olowerdir=lower,upperdir=upper,workdir=work merge
 rm merge/file
 ls -al merge/file
 rm upper/file
 ls -al merge/
 mkdir merge/file

Before commencing with a vfs_rename(..., RENAME_EXCHANGE) verify that the
lookup of "upper" is positive and is a whiteout, and return ESTALE
otherwise.

Reported by: kaixuxia <xiakaixu1987@gmail.com>
Signed-off-by: NMiklos Szeredi <mszeredi@redhat.com>
Fixes: e9be9d5e ("overlay filesystem")
Cc: <stable@vger.kernel.org> # v3.18
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 6cd078702f2f33cb6b19a682de3e9184112f1a46 upstream.

linking a non-copied-up file into a non-copied-up parent results in a
nested call to mutex_lock_interruptible(&oi->lock). Fix this by copying up
target parent before ovl_nlink_start(), same as done in ovl_rename().

~/unionmount-testsuite$ ./run --ov -s
~/unionmount-testsuite$ ln /mnt/a/foo100 /mnt/a/dir100/

 WARNING: possible recursive locking detected
 --------------------------------------------
 ln/1545 is trying to acquire lock:
 00000000bcce7c4c (&ovl_i_lock_key[depth]){+.+.}, at:
     ovl_copy_up_start+0x28/0x7d
 but task is already holding lock:
 0000000026d73d5b (&ovl_i_lock_key[depth]){+.+.}, at:
     ovl_nlink_start+0x3c/0xc1

[SzM: this seems to be a false positive, but doing the copy-up first is
harmless and removes the lockdep splat]

Reported-by: syzbot+3ef5c0d1a5cb0b21e6be@syzkaller.appspotmail.com
Fixes: 5f8415d6 ("ovl: persistent overlay inode nlink for...")
Cc: <stable@vger.kernel.org> # v4.13
Signed-off-by: NAmir Goldstein <amir73il@gmail.com>
Signed-off-by: NMiklos Szeredi <mszeredi@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit babf4770be0adc69e6d2de150f4040f175e24beb upstream.

We hit a BUG on kfree of an ERR_PTR()...

Reported-by: syzbot+ff03fe05c717b82502d0@syzkaller.appspotmail.com
Fixes: 8b88a2e6 ("ovl: verify upper root dir matches lower root dir")
Cc: <stable@vger.kernel.org> # v4.13
Signed-off-by: NAmir Goldstein <amir73il@gmail.com>
Signed-off-by: NMiklos Szeredi <mszeredi@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit e4f3aa2e1e67bb48dfbaaf1cad59013d5a5bc276 upstream.

There is another cast from unsigned long to int which causes
a bounds check to fail with specially crafted input. The value is
then used as an index in the slot array in cdrom_slot_status().

This issue is similar to CVE-2018-16658 and CVE-2018-10940.
Signed-off-by: NYoung_X <YangX92@hotmail.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 985cdcb08a0488558d1005139596b64d73bee267 ]

Mode setting depends on last mode set, in particular
because of exposure calculation when downscale mode
change between subsampling and scaling.
At stream on the last mode was wrongly set to current mode,
so no change was detected and exposure calculation
was not made, fix this.
Signed-off-by: NHugues Fruchet <hugues.fruchet@st.com>
Reviewed-by: NJacopo Mondi <jacopo@jmondi.org>
Tested-by: NJacopo Mondi <jacopo@jmondi.org>
Signed-off-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit ff30e9e8509cb877dc7cbc776b36c70f5bdd290f ]

We accidentally left out the size of the amdgpu_bo_list struct.  It
could lead to memory corruption on 32 bit systems.  You'd have to
pick the absolute maximum and set "num_entries == 59652323" then size
would wrap to 16 bytes.

Fixes: 920990cb ("drm/amdgpu: allocate the bo_list array after the list")
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: NHuang Rui <ray.huang@amd.com>
Reviewed-by: NBas Nieuwenhuizen <basni@chromium.org>
Signed-off-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 62e39417 ]

p9stat_free is more of a cleanup function than a 'free' function as it
only frees the content of the struct; there are chances of use-after-free
if it is improperly used (e.g. p9stat_free called twice as it used to be
possible to)

Clearing dangling pointers makes the function idempotent and safer to use.

Link: http://lkml.kernel.org/r/1535410108-20650-2-git-send-email-asmadeus@codewreck.orgSigned-off-by: NDominique Martinet <dominique.martinet@cea.fr>
Reported-by: syzbot+d4252148d198410b864f@syzkaller.appspotmail.com
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit fb98e29ff1ea5a8118265d11f0e03bc8608a49cb ]

fixes: 6949d864 ("media: ov5640: do not change mode if format or frame interval is unchanged").

Symptom was fuzzy image because of JPEG default format
not being changed according to new format selected, fix this.
Init sequence initialises format to YUV422 UYVY but
sensor->fmt initial value was set to JPEG, fix this.
Signed-off-by: NHugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 31edaa6e7fd8143085a6a60c564447c07e76ed9f ]

Signals available on both i.MX6UL and i.MX6ULL should have the same name
because it is the case of all others common signals, it avoids to make
mistakes (use the wrong ones) and it makes writing device tree files
less complicated. For example:

imx6ul-imx6ull-board.dtsi:
 ...
 pinctrl_uart5: uart5grp {
	fsl,pins = <
		MX6UL_PAD_UART5_TX_DATA__UART5_DCE_TX   0x1b0b1
	 	MX6UL_PAD_UART5_RX_DATA__UART5_DCE_RX   0x1b0b1
 	 >;
 };

imx6ul-board.dts:
 #include <imx6ul.dtsi>
 #include <imx6ul-imx6ull-board.dtsi>
 ...

imx6ull-board.dts:
 #include <imx6ull.dtsi>
 #include <imx6ul-imx6ull-board.dtsi>
 ...

Without this patch, the imx6ull-board.dtb will use
MX6UL_PAD_UART5_RX_DATA__UART5_DCE_RX instead of
MX6ULL_PAD_UART5_RX_DATA__UART5_DCE_RX and the uart5 will be
misconfigured.
Signed-off-by: NSébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit a9ad01bc ]

There are certain filesystem features which we support for reading but
not for writing. We properly refuse to mount such filesystems read-write
however for some features (such as read-only partitions), we don't check
for these features when remounting the filesystem from read-only to
read-write. Thus such filesystems could be remounted read-write leading
to strange behavior (most likely crashes).

Fix the problem by marking in superblock whether the filesystem has some
features that are supported in read-only mode and check this flag during
remount.
Signed-off-by: NJan Kara <jack@suse.cz>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit b4dc44b3 ]

the 9p client code overwrites our glock.client_id pointing to a static
buffer by an allocated string holding the network provided value which
we do not care about; free and reset the value as appropriate.

This is almost identical to the leak in v9fs_file_getlock() fixed by
Al Viro in commit ce85dd58 ("9p: we are leaking glock.client_id
in v9fs_file_getlock()"), which was returned as an error by a coverity
false positive -- while we are here attempt to make the code slightly
more robust to future change of the net/9p/client code and hopefully
more clear to coverity that there is no problem.

Link: http://lkml.kernel.org/r/1536339057-21974-5-git-send-email-asmadeus@codewreck.orgSigned-off-by: NDominique Martinet <dominique.martinet@cea.fr>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 1f447e51 ]

Currently we have structrues comp (which is empty) and comp_info being
used to register and deregister the component.  This mismatch in naming
occurred from a previous commit that renamed aim_info to comp. Fix this
to use consistent component naming in line with most/net, most/sound etc.

This fixes the message two issues, one with a null empty name when
loading the module:

[ 1485.269515] most_core: registered new core component (null)

and an Oops when removing the module:

[ 1485.277971] BUG: unable to handle kernel NULL pointer dereference at 0000000000000008
[ 1485.278648] PGD 0 P4D 0
[ 1485.279253] Oops: 0002 [#2] SMP PTI
[ 1485.279847] CPU: 1 PID: 32629 Comm: modprobe Tainted: P      D WC OE     4.18.0-8-generic #9
[ 1485.280442] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 0.0.0 02/06/2015
[ 1485.281040] RIP: 0010:most_deregister_component+0x3c/0x70 [most_core]
.. etc

Fixes: 1b10a031 ("staging: most: video: remove aim designators")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit d8de8260a45aae8f74af77eae9a162bdc0ed48d2 ]

After GPU reset amdgpu_vm_clear_bo triggers VM flush
but job->vm_pd_addr is not set causing SDMA TO.

v2:
Per advise by Christian König avoid flushing VM for jobs where
job->vm_pd_addr wasn't explicitly set.

v3:
Shortcut vm_flush_needed early.

Fixes cbd5285 drm/amdgpu: move setting the GART addr into TTM.
Signed-off-by: NAndrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 2a3181d9cfd6d5aa48f8527708d0c32072072cef ]

The R-Car Gen3 DU utilises the VSP1 hardware for memory access. The
limits on the RPF and WPF in this pipeline are 8190x8190.

Update the supported maximum sizes accordingly.
Signed-off-by: NKieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 4ee03330 ]

Fixes commit 17be2a29 ("staging: iio:
ad7606: replace range/range_available with corresponding scale").

The AD7606 devices don't have a 2.5V voltage range, they have 5V & 10V
voltage range, which is selectable via the `gpio_range` descriptor.

The scales also seem to have been miscomputed, because when they were
applied to the raw values, the results differ from the expected values.
After checking the ADC transfer function in the datasheet, these were
re-computed.
Signed-off-by: NAlexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: NJonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 693b31b2 ]

Test tm-tmspr might exit before all threads stop executing, because it just
waits for the very last thread to join before proceeding/exiting.

This patch makes sure that all threads that were created will join before
proceeding/exiting.

This patch also guarantees that the amount of threads being created is equal
to thread_num.
Signed-off-by: NBreno Leitao <leitao@debian.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
Signed-off-by: NSasha Levin <sashal@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>