Signed-off-by: NMike Frysinger <michael.frysinger@analog.com>
Signed-off-by: NBryan Wu <bryan.wu@analog.com>

The tle62x0 driver was ignoring all read errors.  This patch makes it
pass such errors up the stack, instead of returning bogus data.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Some error paths in txx9spi_probe wrongly return 0.  This patch fixes them by
using the devres interfaces.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: NDavid Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

After 49dce689, device_for_each_child
iteration hits the master device itself.  Do not call spi_unregister_device()
for the master device.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: NDavid Brownell <david-b@pacbell.net>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use of ptrdiff_t in places like

-                       if (!access_ok(VERIFY_WRITE, u_tmp->rx_buf, u_tmp->len))
+                       if (!access_ok(VERIFY_WRITE, (u8 __user *)
+                                               (ptrdiff_t) u_tmp->rx_buf,
+                                               u_tmp->len))

is wrong; for one thing, it's a bad C (it's what uintptr_t is for; in general
we are not even promised that ptrdiff_t is large enough to hold a pointer,
just enough to hold a difference between two pointers within the same object).
For another, it confuses the fsck out of sparse.

Use unsigned long or uintptr_t instead.  There are several places misusing
ptrdiff_t; fixed.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix the various misspellings of "system", controller", "interrupt" and
"[un]necessary".
Signed-off-by: NRobert P. J. Day <rpjday@mindspring.com>
Signed-off-by: NAdrian Bunk <bunk@kernel.org>

Found these while looking at printk uses.

Add missing newlines to dev_<level> uses
Add missing KERN_<level> prefixes to multiline dev_<level>s
Fixed a wierd->weird spelling typo
Added a newline to a printk
Signed-off-by: NJoe Perches <joe@perches.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Tilman Schmidt <tilman@imap.cc>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Greg KH <greg@kroah.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: James Smart <James.Smart@Emulex.Com>
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Make the SPI framework and drivers stop using class_device.  Update docs
accordingly ...  highlighting just which sysfs paths should be
"safe"/stable.
Signed-off-by: NTony Jones <tonyj@suse.de>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Currently, all QE SPI controllers are almost the same comparing to
MPC83xx's, thus let's use that driver for them.

Tested to work on MPC85xx in loopback mode.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Shrink the runtime footprint of various SPI drivers:

  - Move the probe() routine into the init section where practical,
    using platform_driver_probe() to make that safe.  This often saves
    around 1KB.  Using platform_driver_probe() can also be a correctness
    fix, if the probe routine is already marked __init but the driver
    struct keeps a dangling pointer to it after init section removal.

  - Likewise move remove() routines into the exit sections.

These changes would be inappropriate iff the platform devices were
actually hotpluggable (e.g. they're found on optional addon cards,
or in an FPGA that's dynamically reprogrammed).  In these cases,
that's not the situation; it's an SOC controller and the only device
is initialized before these drivers.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove unused variable & write space
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch cleans up duplicate includes in
	drivers/spi/
Signed-off-by: NJesper Juhl <jesper.juhl@gmail.com>
Acked-by: NDavid Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This changes the uevent buffer functions to use a struct instead of a
long list of parameters. It does no longer require the caller to do the
proper buffer termination and size accounting, which is currently wrong
in some places. It fixes a known bug where parts of the uevent
environment are overwritten because of wrong index calculations.

Many thanks to Mathieu Desnoyers for finding bugs and improving the
error handling.
Signed-off-by: NKay Sievers <kay.sievers@vrfy.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When the spi_mpc83xx driver receives a tx_buf pointer which is NULL, it
only writes one zero filled word to the transmit register.  If the driver
expects to receive more than one word it will wait forever for a second
receive interrupt.  With this patch the controller will shift out zeroes
until all words have been received.
Signed-off-by: NJan Andersson <jan@gaisler.com>
Tested-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Acked-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix cut 'n paste bug in Atmel SPI driver.
Signed-off-by: NAndrew Victor <andrew@sanpeople.com>
Acked-by: NDavid Brownell <david-b@pacbell.net>
Acked-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Correct the name of the spi_txx9 driver (and their in-tree user)
instead of MODULE_ALIAS workaround.  This would be preferable in the
long term.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Update various SPI drivers so they properly support

  - coldplug through "modprobe $(cat /sys/devices/.../modalias)"

  - hotplug through "modprobe $(MODALIAS)"

The basic rule for platform, SPI, and (new style) I2C drivers is just
to make sure that modprobing the driver name works.  In this case, all
the relevant drivers are platform drivers, and this patch either

  (a)	Changes the driver name, if no in-tree code would break;
	this is simpler and thus preferable in the long term.

  (b)	Adds MODULE_ALIAS directives, when in-tree platforms declare
	devices using the current driver name; less desirable.

Most systems will link SPI controller drivers statically, but
there's no point in being needlessly broken.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Jean Delvare <khali@linux-fr.org>
Acked-by: NAndrei Konovalov <akonovalov@ru.mvista.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Git rid of "warning: passing arg 2 of `access_ok' makes pointer from integer
without a cast" reported on SH ...  most architectures use macros in that
test, SH uses inlined functions.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Long ago I've noticed (but didn't pay much attention) that
spi_mpc83xx using PM calculations that differs from what
specs describe. I.e.

u8 pm = mpc83xx_spi->spibrg / (spi->max_speed_hz * 4);

While specs says: "The SPI baud rate generator clock source (either
system clock or system clock divided by 16, depending on DIV16 bit) is
divided by 4 * ([PM] + 1), a range from 4 to 64.".

Thus " - 1" is missing in the spi_mpc83xx's formula.

Why nobody noticed that bug? Probably because sysclk usually less then
user expects, e.g. you expect 200 MHz, but real clock is 198 MHz,
and integer rounding helps when this formula is used.

Suppose it's SPI in QE, SYSCLK at 198 MHz, thus SPIBRG at 99MHz, 25 MHz
requested.

PM = (99MHz / ( 25 MHz * 4 )), PM == 0, output SPICLK will be 24.75 MHz

At lower frequencies this bug is more noticeable, though.

And this bug shows itself in all its beauty if SYSCLK is equal or a bit
more than you expect (200 MHz SYSCLK, 100 MHz SPIBRG):
PM = (100MHz / ( 25 MHz * 4 )), PM == 1, output SPICLK will be 12.625 MHz!
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

For MPC8349E input to the SPI Baud Rate Generator is SYSCLK, but it's
SYSCLK/2 for MPC8323E (SPI in QE).  Fix this, and remove confusion by
renaming the mpc83xx_spi->sysclk member as mpc83xx_spi->spibrg.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This updates some error reporting paths in SPI device setup:

 - Move validation logic for SPI chipselects to spi_new_device(),
   which is where it should always have been.

 - In spi_new_device(), emit error messages if the device can't
   be created.  This is LOTS better than a silent failure; though
   eventually, the calling convention should probably change to
   use the <linux/err.h> conventions.

 - Includes one previously-missing check:  SPI masters must always
   have at least one chipselect, even for dedicated busses which
   always keep it selected!

It also adds a FIXME (IDR for dynamic ID allocation) so the issue doesn't live
purely in my mailbox.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This exposes the hardware loopback mode to drivers, primarily for testing.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The spidev driver doesn't currently expose all SPI communications modes to
userspace.  This passes them all through to the driver.

Two of them are potentially troublesome, in the sense that they could cause
hardware conflicts on shared busses.  It might be appropriate to add some
privilege checks for for those modes.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

spi_mpc83xx should use other shifts when running in QE+LSB mode.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This controller supports LSB-first transfers; let drivers use them.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Magic-numbers-R-Evil
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Documentation clearly states, that mode should not be changed till
SPMODE_ENABLE bit set.  I've seen hangs w/o this patch.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix the include files moved around during the s3c24xx arch moves.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

WARNING: drivers/built-in.o(.text+0x889735): Section mismatch: reference to .init.text:scan_boardinfo (between 'spi_register_master' and '__unregister')
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The SPI core/init code uses a semaphore as mutex.  Use the mutex API instead
of the (binary) semaphore.
Signed-off-by: NMatthias Kaehlcke <matthias.kaehlcke@gmail.com>
Acked-by: NDavid Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This is a driver for SPI controller built into TXx9 MIPS SoCs.
This driver is derived from arch/mips/tx4938/toshiba_rbtx4938/spi_txx9.c.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add OMAP24XX McSPI (Multichannel SPI) controller driver.  This driver is
tested very well under OMAP GIT tree with N800 - Nokia Internet Tablet, and
some other OMAP2 boards.

Recent updates included bugfixes, cleanups, speedups, and better
conformance to the current SPI programming interface.  This doesn't yet
understand the third controller instance on the OMAP 2430.

[david-b@pacbell.net: more minor cleanups to the omap2_mcspi driver]
Signed-off-by: NJuha Yrjölä <juha.yrjola@solidboot.com>
Signed-off-by: NTrilok Soni <soni.trilok@gmail.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Quicc Engine enabled mpc83xx CPU's has a somewhat different HW interface to
the SPI controller.  This patch adds a qe_mode knob that sees to that
needed adaptions are performed.
Signed-off-by: NJoakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Simple SPI master driver for Xilinx SPI controller.
No support for multiple masters.
Not using level 1 drivers from EDK.

[akpm@linux-foundation.org: uninlining]
Signed-off-by: NYuri Frolov <yfrolov@ru.mvista.com>
Signed-off-by: NAndrei Konovalov <akonovalov@ru.mvista.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add support for the Infineon TLE62x0 series of low-side driver chips, such
as the TLE6220 or TLE6230.  These can be viewed as output GPIOs specialized
for power switching applications.  The driver provides a userspace
interface to those GPIOs, and to the switch status they provide.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Tweak Kconfig for the S3C24XX SPI controller drivers.  Both use the bitbang
framework; only one previously said that.  Plus in this case "select" is
the right way to manage that dependency, since folk will not know up front
to enable bitbang in order to even see those S3C drivers in order to enable
them.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Update chipselect handling for atmel_spi:

  * Teach it how to leave chipselect active between messages; this
    helps various drivers work better.

  * Cope with at91rm0200 errata:  nCS0 can't be managed with GPIOs.
    The MR.PCS value is now updated whenever a chipselect changes.
    (This requires SPI pinmux init for that controller to change,
    and also testing on rm9200; doesn't break at91sam9 or avr32.)

  * Fix minor glitches:  spi_setup() must leave chipselects inactive,
    as must removal of the spi_device.

Also tweak diagnostic messaging to be a bit more useful.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Acked-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Minor updates to atmel_spi:

 - DMA:
    * Comments to explain the DMA policies
    * Report any mapping errors from spi_transfer()
    * Remove extra loop for DMA mapping

 - Diagnostics:  report minimum clock rate, if we need to reject a
   spi_setup() request because that rate is too low.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Acked-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The MPC83xx SPI controller clock divider can divide the system clock by not
more then 1024.  The spi_mpc83xx driver does not check this and silently
writes garbage to the SPI controller registers when asked to run at lower
frequencies.  I've tried to run the SPI on a 266MHz MPC8349E with 100kHz
for debugging a bus problem and suddenly was confronted with a 2nd problem
to debug..  ;-)

The patch adds an additional check which avoids writing garbage to the SPI
controller registers and warn the user about it.  This might help others to
avoid simmilar problems.

Cc: Kumar Gala <galak@gate.crashing.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This adds a driver for the LM70-LLP parport adapter, which is an eval board
for the LM70 temperature sensor.  For those without that board, it may be a
simpler example of a parport-to-SPI adapter then spi_butterfly.
Signed-off-by: NKaiwan N Billimoria <kaiwan@designergraphix.com>

Doc, coding style, and interface updates; build fixes.  Minor rename.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>