This is obsolete since the passes got combined.
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

phyid Can't be both TG3_PHY_OUI_1 and TG3_PHY_OUI_2 and TG3_PHY_OUI_3.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Acked-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add missing parentheses
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mib_counters_update() also restarts the timer.
So the timer is dequeued, the stats are read and then the timer is
enqueued again. This is "okay" unless someone unloads the module.
The locking here is also broken:
mib_counters_update() grabs just a simple spinlock. The only thing the
lock is good for is to protect the timer func against other callers
namely mv643xx_eth_stop() && mv643xx_eth_get_ethtool_stats(). That means
if the spinlock is taken via the ethtool path and than the timer kicks
in then the box will lock up.
Signed-off-by: NSebastian Andrzej Siewior <sebastian@breakpoint.cc>
Acked-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

dev_set_rx_mode() grabs netif_addr_lock_bh():

|BUG: sleeping function called from invalid context at /home/bigeasy/git/cryptodev-2.6/mm/slub.c:1599
|in_atomic(): 1, irqs_disabled(): 0, pid: 859, name: ifconfig
|2 locks held by ifconfig/859:
| #0:  (rtnl_mutex){--..}, at: [<c0239ccc>] rtnl_lock+0x18/0x20
| #1:  (_xmit_ETHER){-...}, at: [<c022d094>] dev_set_rx_mode+0x1c/0x30
|[<c029f118>] (dump_stack+0x0/0x14) from [<c003df28>] (__might_sleep+0x11c/0x13c)
|[<c003de0c>] (__might_sleep+0x0/0x13c) from [<c00a8854>] (kmem_cache_alloc+0x30/0xd4)
| r5:c78093a0 r4:c034a47c
|[<c00a8824>] (kmem_cache_alloc+0x0/0xd4) from [<c01a5fd0>] (mv643xx_eth_set_rx_mode+0x70/0x188)
|[<c01a5f60>] (mv643xx_eth_set_rx_mode+0x0/0x188) from [<c022ced0>] (__dev_set_rx_mode+0x40/0xac)
|[<c022ce90>] (__dev_set_rx_mode+0x0/0xac) from [<c022d09c>] (dev_set_rx_mode+0x24/0x30)
| r6:00001043 r5:c78090f8 r4:c7809000
|[<c022d078>] (dev_set_rx_mode+0x0/0x30) from [<c02304c4>] (dev_open+0xe4/0x114)
| r5:c7809350 r4:c7809000
|[<c02303e0>] (dev_open+0x0/0x114) from [<c022fd18>] (dev_change_flags+0xb0/0x190)
| r5:00000041 r4:c7809000
|[<c022fc68>] (dev_change_flags+0x0/0x190) from [<c0270250>] (devinet_ioctl+0x2f0/0x710)
| r7:c7221e70 r6:c7aadb00 r5:00000000 r4:00000001
|[<c026ff60>] (devinet_ioctl+0x0/0x710) from [<c02717c8>] (inet_ioctl+0xd4/0x110)
|[<c02716f4>] (inet_ioctl+0x0/0x110) from [<c021fb74>] (sock_ioctl+0x1f4/0x254)
| r4:c7242b40
|[<c021f980>] (sock_ioctl+0x0/0x254) from [<c00b8160>] (vfs_ioctl+0x38/0x98)
| r6:beec9bb8 r5:00008914 r4:c7242b40
|[<c00b8128>] (vfs_ioctl+0x0/0x98) from [<c00b873c>] (do_vfs_ioctl+0x484/0x4d4)
| r6:00008914 r5:c7242b40 r4:c74db1c0
|[<c00b82b8>] (do_vfs_ioctl+0x0/0x4d4) from [<c00b87cc>] (sys_ioctl+0x40/0x64)
|[<c00b878c>] (sys_ioctl+0x0/0x64) from [<c00269a0>] (ret_fast_syscall+0x0/0x2c)
|[42949399.520000]  r7:00000036 r6:beec9c80 r5:00000041 r4:beec9bb8
Signed-off-by: NSebastian Andrzej Siewior <sebastian@breakpoint.cc>
Acked-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Supporting AR8131, and AR8132.
Signed-off-by: NJie Yang <jie.yang@atheros.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A long time ago we had bugs, primarily in TCP, where we would modify
skb->truesize (for TSO queue collapsing) in ways which would corrupt
the socket memory accounting.

skb_truesize_check() was added in order to try and catch this error
more systematically.

However this debugging check has morphed into a Frankenstein of sorts
and these days it does nothing other than catch false-positives.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit f55c21fd ("forcedeth: call
restore mac addr in nv_shutdown path"), which was introduced to fix
the regression tracked at
http://bugzilla.kernel.org/show_bug.cgi?id=11358 causes the
wake-on-lan mac to be reversed in the shutdown path.  Apparently the
forcedeth situation is rather messy in that the mac we need to
writeback for a subsequent modprobe to work is exactly the reverse of
what is needed for proper wake-on-lan.

The following patch explains the situation in the comments and
makes the call to nv_restore_mac_addr() conditional (only called if
we are not really going for poweroff).

Tobias Diedrich wrote:
> Hmm, I had not tried WOL for some time.
> With 2.6.29-rc3 is see the following behaviour:
> 
> State            WOL Behaviour
> ------------------------------
> shutdown         reversed MAC
> disk/shutdown    reversed MAC
> disk/platform    OK
> 
> Apparently nv_restore_mac_addr() restores the MAC in the wrong order
> for WOL (at least for my PCI_DEVICE_ID_NVIDIA_NVENET_15).  platform
> works, because the MAC is not touched in the nv_suspend() path.
> 
> A possible fix might be to only call nv_restore_mac_addr() if
> system_state != SYSTEM_POWER_OFF.

With the following patch:
shutdown         OK
disk/shutdown    OK
disk/platform    OK
kexec            OK
Signed-off-by: NTobias Diedrich <ranma+kernel@tdiedrich.de>
Tested-by: NPhilipp Matthias Hahn <pmhahn@titan.lahn.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a non-wimax interface is looked up by the stack, a bad pointer is
returned when the looked-up interface is not found in the list (of
registered WiMAX interfaces). This causes an oops in the caller when
trying to use the pointer.

Fix by properly setting the pointer to NULL if we don't exit from the
list_for_each() with a found entry.
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In function sock_getsockopt() located in net/core/sock.c, optval v.val
is not correctly initialized and directly returned in userland in case
we have SO_BSDCOMPAT option set.

This dummy code should trigger the bug:

int main(void)
{
	unsigned char buf[4] = { 0, 0, 0, 0 };
	int len;
	int sock;
	sock = socket(33, 2, 2);
	getsockopt(sock, 1, SO_BSDCOMPAT, &buf, &len);
	printf("%x%x%x%x\n", buf[0], buf[1], buf[2], buf[3]);
	close(sock);
}

Here is a patch that fix this bug by initalizing v.val just after its
declaration.
Signed-off-by: NClément Lecigne <clement.lecigne@netasq.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When compile the latest kernel on IA64 platform,I got a warning:
drivers/net/netxen/netxen_nic_main.c:203: warning: label ‘set_32_bit_mask’ 
defined but not used

We do not need label ‘set_32_bit_mask’  on IA64 platform,So move it to #else.
Signed-off-by: NYang Hongyang <yanghy@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If errors are reported on a frame descriptor, we need to
account for the buffer pages that may have been used for this
error packet and recycle them.  Otherwise, we may get the wrong
pages for the next packet.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

New firmware fixes a data corruption issue when receiving and
placing jumbo frames into host buffers.  In some cases, the
buffer descriptor is not updated correctly and this will lead
to the driver linking the wrong number of pages into the SKB.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

New firmware fixes a data corruption issue when receiving and
placing jumbo frames into host buffers.  In some cases, the
buffer descriptor is not updated correctly and this will lead
to the driver linking the wrong number of pages into the SKB.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ensure that we do not set pcb->data.raw beyond its size, print an error message
and return false if we attempt to. A timout message was printed one too early.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

cn_test_timer_func() is a timer handler and can never use GFP_KERNEL -
there's no point in using gfp_any() here.

Also, use setup_timer().
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The problem is that in_atomic() will return false inside spinlocks if
CONFIG_PREEMPT=n.  This will lead to deadlockable GFP_KERNEL allocations
from spinlocked regions.

Secondly, if CONFIG_PREEMPT=y, this bug solves itself because networking
will instead use GFP_ATOMIC from this callsite.  Hence we won't get the
might_sleep() debugging warnings which would have informed us of the buggy
callsites.

Solve both these problems by switching to in_interrupt().  Now, if someone
runs a gfp_any() allocation from inside spinlock we will get the warning
if CONFIG_PREEMPT=y.

I reviewed all callsites and most of them were too complex for my little
brain and none of them documented their interface requirements.  I have no
idea what this patch will do.
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If no prior break occurs, cnt reaches 101 after the loop, so we are still able
to change speed when cnt has become 100.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove workaround for pcie bug in early revisions of NX3031
(rev 41 or earlier). This is taken care of during firmware init.

The workaround required writing pcie config reg of every
pcie function on a card, not all of which are enabled.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With while (--i > 0) { ... } i reaches 0; print when lance_open() fails
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The large receive buffer queue is not properly tracking the current
index in the case where an early exit occurs.  This can happen when a
page alloc or dma mapping fails.  If this occurs the queue will get
out of sync and invalid indexes can be written to the hardware.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Receive packets were only scaling across 2 of the receive queues. The
value was hardcoded to 2 instead of being based on how many rx queues
were running.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Moved the buffer mapping to a point after TSO logic has modified the
iph->check field. We were seeing stale data on the PCIe bus.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We put the skb back if we can't get mapping for it.  We don't
want unmapped buffers on our receive buffer queue.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We put the page back if we can't get mapping for it.  We don't
want unmapped buffers on our receive buffer queue.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace calls to vlan_hwaccel_rx() and netif_rx().
Thanks to Dave Miller for pointing out the the driver was making
the wrong upcall for passing packets into the stack.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With while (limit--) { ... } limit reaches -1, so 0 means success.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Acked-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Here we do two things:

First, revert "iwlwifi: save PCI state before suspend, restore after
resume".  That misguided patch led to being unable to use iwlwifi
devices after resume.

Next, indicate to PCI driver that the saved PCI state is valid during suspend.

We restore PCI state and enable the device when network interface is created,
similarly PCI state is saved and the device is disabled when network interface
is removed. Thus, when .suspend is called the PCI state is saved and device
is disabled. This is the case even if an interface is never created as PCI
state is saved and device disabled during .probe.

PCI driver assumes PCI state is saved in .suspend. Saving the state at this
time will save state of disabled device and thus cause problems during
resume (resuming a disabled device). We thus indicate directly to PCI
driver that current PCI saved state is valid.
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Tested-by: NAlex Riesen <fork0@users.sf.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Three people (Petr Mensik <pihhan@cipis.net>
["si" should be U+0161 U+00ED], Stephen Ho <stephenhoinhk@gmail.com>
on zd1211-devs and Ismael Ojeda Perez <iojedaperez@gmail.com>
on linux-wireless) reported success in getting TP-Link WN322G/WN422G
working by treating MAXIM_NEW_RF(0x08) as UW2453_RF(0x09) for rf
chip hardware initialization.
Signed-off-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Tested-by: NPetr Mensik <pihhan@cipis.net>
Tested-by: NStephen Ho <stephenhoinhk@gmail.com>
Tested-by: NIsmael Ojeda Perez <iojedaperez@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Christoph Biedl <sourceforge.bnwi@manchmal.in-ulm.de> reported success
in the sourceforge zd1211 mailing list on this addition. This product ID
was supported by the vendor driver ZD1211LnxDrv 2.22.0.0 (and possibly
earlier) and it probably should have been added earlier.
Signed-off-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Tested-by: NChristoph Biedl <sourceforge.bnwi@manchmal.in-ulm.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We try to find the correct outgoing interface for injected frames
based on the TA, but since this is a hack for hostapd 11w, restrict
the heuristic to AP mode interfaces. At some point we'll add the
ability to give an interface index in radiotap or so and just
remove this heuristic again.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org [2.6.28.x]
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Under memory pressure, we may not be able to allocate a new skb for
new packets.  If the allocation fails, ath5k_tasklet_rx will exit but
will leave a buffer in the list with a NULL skb, eventually triggering
a BUG_ON.

Extract the skb allocation from ath5k_rxbuf_setup() and change the
tasklet to allocate the next skb before accepting a packet.

Changes-licensed-under: 3-Clause-BSD
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently, the sunhme driver installs SBus Quattro interrupt handler 
when at least one HME card was initialized correctly and at least one 
Quattro card is present. This breaks when a Quattro card fails 
initialization for whatever reason - IRQ is registered and OOPS happens 
when it fires.

The solution, as suggested by David Miller, was to keep track which 
cards of the Quattro bundles have been initialized, and request/free the 
Quattro IRQ only when all four devices have been successfully 
initialized.

The patch only touches SBus initialization - PCI init already resets the 
card pointer to NULL on init failure.

The patch has been tested on Sun E3500 with SBus and PCI single HME 
cards and one PCI Quattro HME card in a situation where any PCI card 
failed init when the SBus routines tried to init them by mistake.

Additionally it replaces Quattro request_irq panic with error return - 
if this card fails to work, at least let the others work.

Tested on E450 with PCI HME and PCI Quad HME.

[ Minor coding style fixups -DaveM ]
Signed-off-by: NMeelis Roos <mroos@linux.ee>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fore 200 ATM driver fails to handle request_firmware failures and oopses 
when no firmware file was found. Fix it by checking for the right return 
values and propaganting the return value up.
Signed-off-by: NMeelis Roos <mroos@linux.ee>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using u32 in this header breaks the build of iptables.
Signed-off-by: NChuck Ebbert <cebbert@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mdc pin should always be output. Initialize it as output,
so each board code does not need to do this.
Signed-off-by: NPaulius Zaleckas <paulius.zaleckas@teltonika.lt>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>