The current code has info->bufnmb_last to calculate the BUFNMB bits of
PIPEBUF register. However, since the bufnmb_last is initialized in
the usbhs_pipe_init() only, this driver is possible to set unexpected
value to the register if usb_ep_{enable,disable}() are called many times.

So, this patch modifies the pipe configuration via struct
renesas_usbhs_driver_param to simplify the code. Also this patch changes:
 - a double buffer configuration
 - isochronous buffer size from 512 to 1024
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch fixes an issue that NULL pointer dereference happens when
a gadget driver calls usb_ep_dequeue() for ep0 after disconnected
a usb cable. This is because that usbhsg_try_stop() will call
usbhsg_ep_disable(&dcp->ep) when a usb cable is disconnected and
the pipe of dcp (ep0) is set to NULL.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This header file will be removed soon.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Acked-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: NFelipe Balbi <balbi@ti.com>

This patch adds a compatible string to support for R-Car H3.

Since the HS-USB controller of R-Car H3 is almost the same specification
with R-Car Gen2 (these have 16 pipes and usb-dmac), this patch
sets the "type" of renesas_usbhs_driver_param to USBHS_TYPE_RCAR_GEN2.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch fixes the following warning if 64-bit architecture environment:

./drivers/usb/renesas_usbhs/common.c:496:25: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
  dparam->type = of_id ? (u32)of_id->data : 0;
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch adds a compatible string to support for R-Car H3.

Since the HS-USB controller of R-Car H3 is almost the same specification
with R-Car Gen2 (these have 16 pipes and usb-dmac), this patch
sets the "type" of renesas_usbhs_driver_param to USBHS_TYPE_RCAR_GEN2.
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch fixes the following warning if 64-bit architecture environment:

./drivers/usb/renesas_usbhs/common.c:496:25: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
  dparam->type = of_id ? (u32)of_id->data : 0;
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Convert endpoint configuration to new capabilities model.
Signed-off-by: NRobert Baldyga <r.baldyga@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

These changes allow a PHY driver to trigger a VBUS interrupt and
to provide the value of VBUS.
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NPhil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch removes the deprecated API of extcon and then use the new extcon API
with the unique id to indicate the each external connector (USB-HOST).
- extcon_get_cable_state(*edev, char *) -> extcon_get_cable_state_(*edev, id)

Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Peter Chen <peter.chen@freescale.com>
Cc: Varka Bhadram <varkab@cdac.in>
Cc: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

These changes allow a PHY driver to trigger a VBUS interrupt and
to provide the value of VBUS.
Signed-off-by: NPhil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch fixes an issue that sometimes this controller is not able
to complete the Control write status stage.

This driver should enable DCPCTR.CCPL and PID_BUF to complete the status
stage. However, if this driver detects the ctrl_stage interruption first
before the control write data is received, this driver will clear the
PID_BUF wrongly in the usbhsf_pio_try_pop(). To avoid this issue, this
patch doesn't clear the PID_BUF in the usbhsf_pio_try_pop().
(Since also the privious code doesn't disable the PID_BUF after a control
 transfer was finished, this patch doesn't have any side efforts.)
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch fixes an issue for control write. When usbhsf_prepare_pop()
is called after this driver called a gadget setup function, this controller
doesn't receive the control write data. So, this patch adds a code to clear
the fifo for control write in usbhsf_prepare_pop().
Signed-off-by: NKazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch adds a compatible string to support for R-Car E2.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>" in patch 2
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Since the HSUSB controllers of R-Car Gen2 are the same specification
(they have 16 pipes and usb-dmac), this patch changes USBHS_TYPE_R8A7790
and USBHS_TYPE_R8A7791 to USBHS_TYPE_RCAR_GEN2.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch fixes an issue that sometimes this controller is not able
to complete the Control write status stage.

This driver should enable DCPCTR.CCPL and PID_BUF to complete the status
stage. However, if this driver detects the ctrl_stage interruption first
before the control write data is received, this driver will clear the
PID_BUF wrongly in the usbhsf_pio_try_pop(). To avoid this issue, this
patch doesn't clear the PID_BUF in the usbhsf_pio_try_pop().
(Since also the privious code doesn't disable the PID_BUF after a control
 transfer was finished, this patch doesn't have any side efforts.)
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch fixes an issue for control write. When usbhsf_prepare_pop()
is called after this driver called a gadget setup function, this controller
doesn't receive the control write data. So, this patch adds a code to clear
the fifo for control write in usbhsf_prepare_pop().
Signed-off-by: NKazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Since the DT should describe the hardware (not the driver limitation),
This patch revises the binding document about the dma-names to change
simple numbering as "ch%d" instead of "tx<n>" and "rx<n>".

Also this patch fixes the actual code of renesas_usbhs driver to handle
the new dma-names.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: NMark Rutland <mark.rutland@arm.com>
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

After the renesas_usbhs driver is enabled in ARM multi_v7_defconfig,
we now get a new warning:

renesas_usbhs/mod.c: In function 'usbhs_interrupt':
renesas_usbhs/mod.c:246:7: warning: 'intenb1' may be used uninitialized in this function [-Wmaybe-uninitialized]

gcc correctly points to a problem here, for the case that the
device is in host mode, we use the intenb1 variable without
having assigned it first. The state->intsts1 has a similar
problem, but gcc cannot know that.

This avoids the problem by initializing both sides of the
comparison to zero when we don't read them from the respective
registers.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Fixes: 88a25e02 ("usb: renesas_usbhs: Add access control for INTSTS1 and INTENB1 register")
Acked-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

INTSTS1 and INTENB1 register of renesas_usbhs can access only Host mode.
This adds process of accessing INTSTS1 and INTENB1 only when renesas_usbhs
is Host mode.
Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Since the DT should describe the hardware (not the driver limitation),
This patch revises the binding document about the dma-names to change
simple numbering as "ch%d" instead of "tx<n>" and "rx<n>".

Also this patch fixes the actual code of renesas_usbhs driver to handle
the new dma-names.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: NMark Rutland <mark.rutland@arm.com>
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Current usbhs_for_each_dfifo macro will read out-of-array's
memory after last loop operation.
It was not good C language operation, and the binary which was
compiled by (at least) gcc 4.8.1 is broken.

This patch is based on
925403f4
(usb: renesas_usbhs: tidyup original usbhsx_for_each_xxx macro)
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Fix  using the  bare number to set the 'bDescriptorType' field of the Hub
Descriptor while the value  is #define'd in <linux/usb/ch11.h>.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

According to the gadget.h, a "complete" function will always be called
with interrupts disabled. However, sometimes usbhsg_queue_pop() function
is called with interrupts enabled. So, this function should be held by
usbhs_lock() to disable interruption. Also, this driver has to call
spin_unlock() to avoid spinlock recursion by this driver before calling
usb_gadget_giveback_request().
Otherwise, there is possible to cause a spinlock suspected in a gadget
complete function.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Some Renesas SoCs have the USB-DMAC. It is able to terminate transfers
when a short packet is received, even if less bytes than the transfer
counter size have been received. Also, it is able to send a short
packet even if the packet size is not multiples of 8bytes.

Since the previous code has used the interruption of USBHS controller
when receiving packets even if this driver has used a dmac, a lot of
interruptions has happened. This patch will reduce such interruptions.

This patch allows to use the USB-DMAC on R-Car H2 and M2.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch fixes the setup sequence in xfer_work(). Otherwise,
sometimes a usb transaction will get stuck.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

To connect the channel of USB-DMAC to USBHS DnFIFO number, this patch
adds this channel/FIFO number in dma-names. Otherwise, this driver
needs to add analysis code for device tree.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The renesas usbhs driver calls extcon_get_edev_by_phandle(), which
is defined in drivers/extcon/extcon-class.c, and that can be a
loadable module. If the extcon-class support is disabled, usbhs
will work correctly for all devices that do not need extcon.

However, if extcon-class is a loadable module, and usbhs is
built-in, the kernel fails to link. In order to solve that,
we need a Kconfig dependency that allows extcon to be disabled
but does not allow usbhs built-in if extcon is a module.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch fixes an issue that the following commit causes NULL
pointer dereference in dma_release_channel().
 "usb: renesas_usbhs: add support for requesting DT DMA"
 (commit id abd2dbf6)

The usbhsf_dma_init_dt() should set fifo->{t,r}x_chan to NULL if
dma_request_slave_channel_reason() returns IS_ERR value.
Otherwise, usbhsf_dma_quit() will call dma_release_channel(), and then
NULL pointer dereference happens.
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Tested-by: NSimon Horman <horms+renesas@verge.net.au>
Reported-by: NSimon Horman <horms@verge.net.au>
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Set value for common is_selfpowered.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch adds dma_request_slave_channel_reason() calling to request
dma slave channels for multiplatform environment.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

To add support for requesting DT DMA in the future, this patch adds
usbhsf_dma_init_pdev() function.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Fix  using the  bare number  to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Fix  using the  bare number  to set the 'wHubCharacteristics' field of the Hub
Descriptor while the values are #define'd in <linux/usb/ch11.h>.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

On the Renesas R8A7791 SoC based boards there's MAX3355 USB OTG chip and mini-AB
USB connector corresponding to USB port 0 driven either by EHCI/OHCI or  Renesas
USBHS gadget controller. And we'd like the host/gadget  drivers to work based on
the cable type connected. An 'extcon' driver for MAX3355 has been written, so we
only need to bind  to it via device tree which I'm doing in this patch.

(Perhaps, it would also make sense to use OTG HNP when the USBHS host mode is
active and a B-cable is connected but I don't have access to host-capable USBHS,
so  wouldn't be able to test it.)
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

There is a typo ("prove" instead of "probe") in the error message printed when
the platform initialization fails. Replace that word with more fitting "init".
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

usbhsc_drvcllbck_notify_hotplug() always returns 0, so it's rather pointless to
store and check its result for being < 0.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch expands USB-DMAC channels for R-Car Gen2 SoCs. The SoCs
have 4 channels. If d{2,3}_{t,x}x_id are not set, this driver never
uses the expanded USB-DMAC channels.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

To extend DnFIFOs in the future, this patch adds a new macro because
some SoCs don't the "port" address for DnFIFOs.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

To expand DnFIFOs in the future, this patch standardizes the d{0,1}fifo
control using new macros.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>