This patch implements proper transmission flow control on mshX.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Split wlan_add_card() into a part that just setups kernel parameters and
into the function libertas_activate_card(), which will implizitly use
hardware functions by the started thread.

This allows us later to do something like this:

priv = libertas_add_card();
priv->hw_command_to_host = if_usb_command_to_host;
priv->hw_xxxx = if_usb_xxxx;
priv->hw_yyyy = if_usb_yyyy;
wlan_activate_card()

and of course the CF driver can set it's own functions.
Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The reset_device() logic is only needed for USB devices, not for CF
devices.
Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The subject says it all.
Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* a newline was missing
* changed %32s to '%s', no need to right justify the ESSID
Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It's not really needed, because we can call wlan_remove_card() with
wlan_private* anyway.
Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It used to be LBS_DEB_MAIN, now it's LBS_DEB_THREAD

Also fixed a missing ":" in lbs_deb_enter()
Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patches adds the two functions wlan_add_mesh() and wlan_remove_mesh(),
which are responsible for the mshX interface. In a CF driver with a non-
mesh-aware firmware you can omit the calls to this functions.
Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* renamed module parameter back to libertas_debug
* change from bit shifts to constants, that way it's easier to look at the
    source and specify the libertas_debug=0xXXXX module parameter
* moved module_param from fw.c to main.c, where it belongs better
Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The debug output of libertas was either not present or it was overwhelming.
This patch adds the possibility to specify a bitmask for the area of
interest. One should then only get the desired output.
Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This reduces usb8xxx.ko by 951 bytes (text) and 256 bytes (data)
when PROC_DEBUG isn't defined.
Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The previous scan fix did not account for scan paths other than set_scan()
that need to do a full scan at once.

Add a "full_scan" parameter to wlan_scan_networks() to control such
behaviour.
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move libertas_wlan_data_rates into wext.c and make it static. wext.c is the
only user of this array.
Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For me it looks cleaner, because it removes one level of indirection.
Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

DEV_NAME_LEN is already defined in defs.h and that is sufficient.
Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove filename from debug output because it's way too long.
Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Subject says it all.
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

rmmod did not remove /sys/kernel/debug/libertas_wireless/eth1/
subscribed_events/high_snr. After I fixed this, I noticed that
it also didn't remove /sys/kernel/debug/libertas_wireless/eth1
as well.
Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Renames wlan_association_worker into libertas_association_worker
Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Scan two channels per each command on set_scan(), then bail out and let
get_scan() continue the scanning work up to the last channel.

This gives time to the firmware so it can go back to the association
channel and keep the connection alive.

Fixes http://dev.laptop.org/ticket/841Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

* git://git.infradead.org/mtd-2.6:
  [JFFS2] Fix obsoletion of metadata nodes in jffs2_add_tn_to_tree()
  [MTD] Fix error checking after get_mtd_device() in get_sb_mtd functions
  [JFFS2] Fix buffer length calculations in jffs2_get_inode_nodes()
  [JFFS2] Fix potential memory leak of dead xattrs on unmount.
  [JFFS2] Fix BUG() caused by failing to discard xattrs on deleted files.
  [MTD] generalise the handling of MTD-specific superblocks
  [MTD] [MAPS] don't force uclinux mtd map to be root dev

Several people have reported LITE-ON LTR-48246S detection failed
because SETXFER fails.  It seems the device raises IRQ too early after
SETXFER.  This is controller independent.  The same problem has been
reported for different controllers.

So, now we have pata_via where the controller raises IRQ before it's
ready after SETXFER and a device which does similar thing.  This patch
makes libata always execute SETXFER via polling.  As this only happens
during EH, performance impact is nil.  Setting ATA_TFLAG_POLLING is
also moved from issue hot path to ata_dev_set_xfermode() - the only
place where SETXFER can be issued.

Note that ATA_TFLAG_POLLING applies only to drivers which implement
SFF TF interface and use libata HSM.  More advanced controllers ignore
the flag.  This doesn't matter for this fix as SFF TF controllers are
the problematic ones.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
  [SCSI] JAZZ ESP and SUN ESP need SPI_ATTRS
  [SCSI] atari_NCR5380: update_timeout removal
  [SCSI] aacraid: fix shutdown handler to also disable interrupts.
  [SCSI] qla2xxx: fix timeout in qla2x00_down_timeout
  [SCSI] fix CONFIG_SCSI_WAIT_SCAN=m

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: reduce raciness when input handlers disconnect
  Input: ucb1x00 - do not access input_dev->private directly
  Input: logips2pp - fix typo in Kconfig
  Input: db9 - do not ignore dev2 module parameter

* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
  [ICMP]: Fix icmp_errors_use_inbound_ifaddr sysctl
  [IPV4]: Fix "ipOutNoRoutes" counter error for TCP and UDP
  [NET] gso: Fix GSO feature mask in sk_setup_caps
  [TCP]: Fix GSO ignorance of pkts_acked arg (cong.cntrl modules)
  [NET]: Fix comparisons of unsigned < 0.
  [NET]: Make net watchdog timers 1 sec jiffy aligned.
  [ATM]: Fix warning.
  [TCP]: Use default 32768-61000 outgoing port range in all cases.
  [AF_UNIX]: Fix datagram connect race causing an OOPS.
  [TG3]: Fix link problem on Dell's onboard 5906.
  [AF_UNIX]: Make socket locking much less confusing.

* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
  [ATA]: Don't allow to enable this for SPARC64 without PCI.
  [VIDEO]: XVR500 and XVR2500 require FB=y

We've had several reoprts of the CPU jumping to 0x00000000 is do_ioctl().  I
assume that there's a race and someone is zeroing out the ioctl handler while
this CPU waits for the lock_kernel().

The patch adds code to detect this, then emits stuff which will hopefuly lead
us to the culprit.
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Rafael gets this on an SMP box with kernel preemption enabled, during
hibernation and restore (100% of the time):

Enabling non-boot CPUs ...
BUG: using smp_processor_id() in preemptible [00000001] code: bash/4514
caller is mtrr_save_state+0x9/0x40

Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix SPI dynamic bus ID assignment to start at 2^15-1 rather than a negative
number.  Valid bus ids are supposed to be positive, and are (now) stored in
an 's16' value.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Reported by Meelis Roos.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Atari SCSI driver fixes: remove update_timeout kludge
Signed-off-by: NMichael Schmitz <schmitz@debian.org>
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Acked-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

There is a race between input handler's release() and disconnect()
methods: when input handler disconnects it wakes up all regular
users and then process to walk user list to wake up async. users.
While disconnect() walks the list release() removes elements of
the same list causing oopses.

While this is not a substibute for proper locking we can reduce
odds of getting an oops if we wake up normal readers after walking
the list.
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Use input_get_drvdata() and input_set_drvdata() helpers to do that.
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>
Acked-by: NPavel Machek <pavel@ucw.cz>

Based upon a report from Meelis Roos.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently when icmp_errors_use_inbound_ifaddr is set and an ICMP error is
sent after the packet passed through ip_output(), an address from the
outgoing interface is chosen as ICMP source address since skb->dev doesn't
point to the incoming interface anymore.

Fix this by doing an interface lookup on rt->dst.iif and using that device.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NWei Dong <weidong@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This isn't a bug just yet as only TCP uses sk_setup_caps for GSO.
However, if and when UDP or something else starts using it this is
likely to cause a problem if we forget to add software emulation
for it at the same time.

The problem is that right now we translate GSO emulation to the
bitmask NETIF_F_GSO_MASK, which includes every protocol, even
ones that we cannot emulate.

This patch makes it provide only the ones that we can emulate.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>