We don't need to store the number of bytes transferred in our host
structure - we can store this directly in data->bytes_xfered.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

We don't need to switch to data available interrupts if there's at
least half a FIFO depth worth of data remaining, as we'll still get
the FIFO half full interrupt.  Keep this interrupt masked off until
we have less than half the FIFO depth worth of data remaining.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The sg_miter API provides the required cache maintainence, so we don't
need to do that ourselves.  Remove the unnecessary additional cache
maintainence.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The data counter counts the number of bytes transferred on the MMC bus.
When a FIFO overrun occurs, we will not have transferred a FIFOs-worth
of data to memory, and so the data counter will be a FIFOs-worth ahead.
If this occurs on a block boundary, we will report one too many sectors
as successful.  Fix this.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

We should not report incomplete blocks on error.  Return the number of
bytes successfully transferred, rounded down to the nearest block.
Acked-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

When we encounter an error, make sure we complete the transaction
otherwise we'll leave the request dangling.
Acked-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The MMCIDATACNT register contain the number of byte left at error
not the number of words, so loose the << 2 thing. Further if CRC
fails on the first block, we may end up with a negative number
of transferred bytes which is not good, and the formula was in
wrong order.
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Don't read the command response from the registers when either the
command timed out (because there was no response from the card) or
the checksum on the response was invalid.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NChris Ball <cjb@laptop.org>

Implement a suggestion from Russell to drop the use of blockend
interrupts altogether and instead rely on the data counter.

Tested with error-free cards on U300, U8500 and RealView PB1176.
Signed-off-by: NUlf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Make the MMCI announcement printk say which primecell part number
has been found.  Display the revision as an unsigned decimal, and
display only the first 8 hex digits of the base address unless it's
larger.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

I misread the datasheet as if bypass mode was not available at all
on the ux500's, I was wrong. It is there, the datasheet just
states that you should not have to use it.
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The Ux500 variant of this block has a different divider.
The value used right now is too big and which means a loss
in performance. This fix corrects it. Also expand the math
comments a bit so it's clear what's happening. Further
the Ux500 variant does not like if we use the BYPASS bit,
instead we are supposed to set the clock divider to zero.
Signed-off-by: NUlf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This adds some minor variant data and trickery to enable SDIO
on the ST Micro variants of MMCI/PL180.
Signed-off-by: NMarcin Mielczarczyk <marcin.mielczarczyk@tieto.com>
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

On the U300 the MCI_DATAEND and MCI_DATABLOCKEND IRQs can arrive
out-of-order. Replace an ugly #ifdef hack with a proper runtime
solution which models what is really happening.

In the U300 DMA mode and on all Ux500 models, the MCI_DATABLOCKEND
flag isn't properly cleared in hardware following and ACK leading
to all kind of weird behaviour when the flag is still up in
subsequent interrupts, so we add two flags indicating the
error and handle this runtime.

Cc: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The DBx500 variants have only one IRQ line hooked up.  Allow these (and
any other implementations which choose to use only one irq) to work by
directing the PIO interrupts also to the first IRQ line.
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

After discovering a problem in regulator reference counting I took Mark
Brown's advice to move the reference count into the MMC core by making the
regulator status a member of struct mmc_host.

I took this opportunity to also implement NULL versions of
the regulator functions so as to rid the driver code from
some ugly #ifdef CONFIG_REGULATOR clauses.
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Reviewed-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Sundar Iyer <sundar.iyer@stericsson.com>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Matt Fleming <matt@console-pimps.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Cliff Brake <cbrake@bec-systems.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

We have deprecated the distinction between hardware and physical
segments in the block layer.  Consolidate the two limits into one in
drivers/mmc/.
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Currently the kernel is screaming about slowpath at me for the
wp/cd callbacks. Switch to the _cansleep variants so as to silence
this.
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The card may be always present on the board, and for these cases neither
a status callback nor a card detect GPIO is required, and card detection
polling can be disabled.
Acked-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

If an IRQ can be requested on the card detected GPIO, use it instead of
polling.
Acked-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The Ux500 variant has a 32-word FIFO (TXFIFOEMPTY is asserted when it
has 2 left) and TXFIFOHALFEMPTY is repurposed as TXFIFOBURSTWRITEABLE,
with a burst being defined as 8-words.  Likewise for RX.
Acked-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

On some platforms, the GPIO value from the gpio_cd pin doesn't need to
be inverted to get it active high.  Add a cd_invert platform data
parameter and change existing platforms using GPIO for CD (only
Realview) to enable it.
Acked-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The MMC card detection sense has become really confused with negations
at various levels, leading to some platforms not detecting inserted
cards.  Fix this by converting everything to positive logic throughout,
thereby getting rid of these negations.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The Ux500 variant has a 24-bit MMCIDATALENGTH register, as opposed to
the 16-bit one on the ARM version.
Acked-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Although both the U300 and Ux500 use ST variants, the HWFCEN bits are at
different positions, so use the variant_data to store the information.
Acked-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add a variant_data structure to handle the differences between the
various variants of this peripheral.  Add a first quirk for a default
MCICLOCK value, required on the Ux500 variant where the enable bit needs
to be always set, since it controls access to some registers.
Acked-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Platforms may have some external power control which need to be
controlled from board specific code.  Rename the translate_vdd()
callback to vdd_handler() and pass it the power mode.
Acked-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Use the MMC core's ability to poll for card detection.  This also has
the advantage of doing the gpio_get_value from a workqueue instead of
timer, allowing the gpio to be on a sleeping gpiochip.
Acked-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Fix the data transfer size to allow multi block transfers to work.
Acked-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The mmci driver's SG list iteration logic assumes that each SG entry
spans only one page, and only maps and flushes one page of the sg.  This
is not a valid assumption.  Fix it by converting the driver to the
sg_miter API, which correctly handles sgs which span multiple pages.
Acked-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NRabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Even though many mmc host drivers pass a pm_message_t argument to
mmc_suspend_host() that argument isn't used the by MMC core.  As host
drivers are converted to dev_pm_ops they'll have to construct
pm_message_t's (as they won't be passed by the PM subsystem any more) just
to appease the mmc suspend interface.

We might as well just delete the unused paramter.
Signed-off-by: NMatt Fleming <matt@console-pimps.org>
Acked-by: NAnton Vorontsov <cbouatmailru@gmail.com>
Acked-by: Michal Miroslaw <mirq-linux@rere.qmqm.pl>ZZ
Acked-by: NSascha Sommer <saschasommer@freenet.de>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This introduce the field f_max into the mmci_platform_data,
making it possible to pass in a desired block clocking frequency
from a board configuration. This is often more desirable than
using a module parameter. We keep the module parameter as a
fallback as well as the default frequency specified for this
parameter if a parameter is not provided.

This also adds some kerneldoc style documentation to the
platform data struct in mmci.h.
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This adds support for an 8bit wide bus to the card (data lines
MCIDAT0 through 7 exist) on the ST Micro version and alters the
U300 platform to support this. Also add some ST_ prefix to the
ST-specific registers.
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This removes the custom DBG macro in favor of the in-kernel
dev_dbg() macro. Probably a leftover from a time when dev_dbg()
didn't yet exist. Also remove a printk() in favor of dev_err().
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

In the U300 some hardware bug makes the status flag not come up
signalling a successful write (or anything else, like an error, for
that matter) on write requests. This little quirk makes the writes
work on U300.
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This fixes a leftover instance of using the 0x80 numeral instead
of the new AMBA_VENDOR_ST enum in the MMCI/PL180 driver.
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The #ifdefs in the MMCI driver were erroneous and just masking
a bug in the U300 generic GPIO implementation. This removes the
ifdefs and fixes the U300 generic GPIO instead.
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This enables the use of a regulator to power the MMCI/PL180
PrimeCell. The OCR mask is calculated and voltage is set using
the new MMC core functions for discovering voltage ranges
in regulators. The platform translate_vdd function which basically
controls the 4 lines out of the PL180 is disabled if you use a
regulator instead.
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This moves the mmci platform data definition struct away from
arch/arm/include/asm/mach/mmc.h into the more proper place among
the other primecells in include/linux/amba/mmci.h and at the same
time renames it to "mmci.h", and also the struct in this file
confusingly named mmc_platform_data has been renamed
mmci_platform_data for clarity.

Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This makes it possible to pass down the host controller
capabilities for the MMCI driver using the platform data. It
also provides the capabilties for the U300 implementation as an
example, and makes sure the 4bit wide mode is set if this is
requested by the ios() now that we can actually set that
capability for a platform.
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>