The number of entries is multiplied by the entry size, which can
overflow on 32-bit hosts.  Bound the entry count instead.
Reported-by: NDavid Wagner <daw@cs.berkeley.edu>
Cc: stable@kernel.org
Signed-off-by: NAvi Kivity <avi@redhat.com>

Debug registers may only be accessed from cpl 0.  Unfortunately, vmx will
code to emulate the instruction even though it was issued from guest
userspace, possibly leading to an unexpected trap later.

Cc: stable@kernel.org
Signed-off-by: NAvi Kivity <avi@redhat.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

kvm_mmu_slot_remove_write_access already calls it.
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Instead of saving the debug registers from the processor to a kvm data
structure, rely in the debug registers stored in the thread structure.
This allows us not to save dr6 and dr7.

Reduces lightweight vmexit cost by 350 cycles, or 11 percent.
Signed-off-by: NAvi Kivity <avi@redhat.com>

update_cr8_intercept() can be triggered from userspace while there
is no apic present.
Signed-off-by: NAvi Kivity <avi@redhat.com>

Segment descriptors tables can be placed on two non-contiguous pages.
This patch makes reading segment descriptors by linear address.
Signed-off-by: NMikhail Ershov <Mike.Ershov@gmail.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

We're in arch/x86, what could we possibly be emulating?
Signed-off-by: NAvi Kivity <avi@redhat.com>

According to 16.2.5 in the SDM, eflags.vm in the tss is consulted before loading
and new segments.  If eflags.vm == 1, then the segments are treated as 16-bit
segments.  The LDTR and TR are not normally available in vm86 mode so if they
happen to somehow get loaded, they need to be treated as 32-bit segments.

This fixes an invalid vmentry failure in a custom OS that was happening after
a task switch into vm8086 mode.  Since the segments were being mistakenly
treated as 32-bit, we loaded garbage state.
Signed-off-by: NAnthony Liguori <aliguori@us.ibm.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Since on vcpu entry we do it only if apic is enabled we should do
it when TPR is changed while apic is disabled. This happens when windows
resets HW without setting TPR to zero.
Signed-off-by: NGleb Natapov <gleb@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

We ignore writes to the perfctr msrs. Ignore reads as well.

Kaspersky antivirus crashes Windows guests if it can't read
these MSRs.
Signed-off-by: NAmit Shah <amit.shah@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

So far unprivileged guest callers running in ring 3 can issue, e.g., MMU
hypercalls. Normally, such callers cannot provide any hand-crafted MMU
command structure as it has to be passed by its physical address, but
they can still crash the guest kernel by passing random addresses.

To close the hole, this patch considers hypercalls valid only if issued
from guest ring 0. This may still be relaxed on a per-hypercall base in
the future once required.

Cc: stable@kernel.org
Signed-off-by: NJan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

If userspace knows that the kernel part supports 1GB pages it can enable
the corresponding cpuid bit so that guests actually use GB pages.
Signed-off-by: NJoerg Roedel <joerg.roedel@amd.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Commit f0a3602c20 ("KVM: Move interrupt injection logic to x86.c") does not
update the cr8 intercept if the lapic is disabled, so when userspace updates
cr8, the cr8 threshold control is not updated and we are left with illegal
control fields.

Fix by explicitly resetting the cr8 threshold.
Signed-off-by: NAvi Kivity <avi@redhat.com>

Now KVM allow guest to modify guest's physical address of EPT's identity mapping page.

(change from v1, discard unnecessary check, change ioctl to accept parameter
address rather than value)
Signed-off-by: NSheng Yang <sheng@linux.intel.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

Use kvm_get_gdt() and kvm_read_ldt() to reduce inline assembly code.

Cc: Avi Kivity <avi@redhat.com>
Cc: kvm@vger.kernel.org
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

Use get_desc_base() and get_desc_limit() to get the base address and
limit in desc_struct.

Cc: Avi Kivity <avi@redhat.com>
Cc: kvm@vger.kernel.org
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

Remove kvm_cpu_has_interrupt() and kvm_arch_interrupt_allowed() from
interface between general code and arch code. kvm_arch_vcpu_runnable()
checks for interrupts instead.
Signed-off-by: NGleb Natapov <gleb@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Signed-off-by: NGleb Natapov <gleb@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

ioeventfd is a mechanism to register PIO/MMIO regions to trigger an eventfd
signal when written to by a guest.  Host userspace can register any
arbitrary IO address with a corresponding eventfd and then pass the eventfd
to a specific end-point of interest for handling.

Normal IO requires a blocking round-trip since the operation may cause
side-effects in the emulated model or may return data to the caller.
Therefore, an IO in KVM traps from the guest to the host, causes a VMX/SVM
"heavy-weight" exit back to userspace, and is ultimately serviced by qemu's
device model synchronously before returning control back to the vcpu.

However, there is a subclass of IO which acts purely as a trigger for
other IO (such as to kick off an out-of-band DMA request, etc).  For these
patterns, the synchronous call is particularly expensive since we really
only want to simply get our notification transmitted asychronously and
return as quickly as possible.  All the sychronous infrastructure to ensure
proper data-dependencies are met in the normal IO case are just unecessary
overhead for signalling.  This adds additional computational load on the
system, as well as latency to the signalling path.

Therefore, we provide a mechanism for registration of an in-kernel trigger
point that allows the VCPU to only require a very brief, lightweight
exit just long enough to signal an eventfd.  This also means that any
clients compatible with the eventfd interface (which includes userspace
and kernelspace equally well) can now register to be notified. The end
result should be a more flexible and higher performance notification API
for the backend KVM hypervisor and perhipheral components.

To test this theory, we built a test-harness called "doorbell".  This
module has a function called "doorbell_ring()" which simply increments a
counter for each time the doorbell is signaled.  It supports signalling
from either an eventfd, or an ioctl().

We then wired up two paths to the doorbell: One via QEMU via a registered
io region and through the doorbell ioctl().  The other is direct via
ioeventfd.

You can download this test harness here:

ftp://ftp.novell.com/dev/ghaskins/doorbell.tar.bz2

The measured results are as follows:

qemu-mmio:       110000 iops, 9.09us rtt
ioeventfd-mmio: 200100 iops, 5.00us rtt
ioeventfd-pio:  367300 iops, 2.72us rtt

I didn't measure qemu-pio, because I have to figure out how to register a
PIO region with qemu's device model, and I got lazy.  However, for now we
can extrapolate based on the data from the NULLIO runs of +2.56us for MMIO,
and -350ns for HC, we get:

qemu-pio:      153139 iops, 6.53us rtt
ioeventfd-hc: 412585 iops, 2.37us rtt

these are just for fun, for now, until I can gather more data.

Here is a graph for your convenience:

http://developer.novell.com/wiki/images/7/76/Iofd-chart.png

The conclusion to draw is that we save about 4us by skipping the userspace
hop.

--------------------
Signed-off-by: NGregory Haskins <ghaskins@novell.com>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

When kvm is in hpet_legacy_mode, the hpet is providing the timer
interrupt and the pit should not be. So in legacy mode, the pit timer
is destroyed, but the *state* of the pit is maintained. So if kvm or
the guest tries to modify the state of the pit, this modification is
accepted, *except* that the timer isn't actually started. When we exit
hpet_legacy_mode, the current state of the pit (which is up to date
since we've been accepting modifications) is used to restart the pit
timer.

The saved_mode code in kvm_pit_load_count temporarily changes mode to
0xff in order to destroy the timer, but then restores the actual
value, again maintaining "current" state of the pit for possible later
reenablement.

[avi: add some reserved storage in the ioctl; make SET_PIT2 IOW]
[marcelo: fix memory corruption due to reserved storage]
Signed-off-by: NBeth Kon <eak@us.ibm.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

We emulate x2apic in software, so host support is not required.
Signed-off-by: NGleb Natapov <gleb@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

This will save a couple of IPIs.
Signed-off-by: NGleb Natapov <gleb@redhat.com>
Acked-by: NMarcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Some Windows versions check whether the BIOS has setup MMI/O for
config space accesses on AMD Fam10h CPUs, we say "no" by returning 0 on
reads and only allow disabling of MMI/O CfgSpace setup by igoring "0" writes.
Signed-off-by: NAndre Przywara <andre.przywara@amd.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

This reverts commit 6c20e1442bb1c62914bb85b7f4a38973d2a423ba.

To my understanding, it became obsolete with the advent of the more
robust check in mmu_alloc_roots (89da4ff17f). Moreover, it prevents
the conceptually safe pattern

 1. set sregs
 2. register mem-slots
 3. run vcpu

by setting a sticky triple fault during step 1.
Signed-off-by: NJan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Windows 7 tries to update the CPU's microcode on some processors,
so we ignore the MSR write here. The patchlevel register is already handled
(returning 0), because the MSR number is the same as Intel's.
Signed-off-by: NAndre Przywara <andre.przywara@amd.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

This patch implements MSR interface to local apic as defines by x2apic
Intel specification.
Signed-off-by: NGleb Natapov <gleb@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Directed EOI is specified by x2APIC, but is available even when lapic is
in xAPIC mode.
Signed-off-by: NGleb Natapov <gleb@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Signed-off-by: NAvi Kivity <avi@redhat.com>

Linux guests will try to enable access to the extended PCI config space
via the I/O ports 0xCF8/0xCFC on AMD Fam10h CPU. Since we (currently?)
don't use ECS, simply ignore write and read attempts.
Signed-off-by: NAndre Przywara <andre.przywara@amd.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

This changes bus accesses to use high-level kvm_io_bus_read/kvm_io_bus_write
functions. in_range now becomes unused so it is removed from device ops in
favor of read/write callbacks performing range checks internally.

This allows aliasing (mostly for in-kernel virtio), as well as better error
handling by making it possible to pass errors up to userspace.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

switch pit creation to slots_lock. slots_lock is already taken for read
everywhere, so we only need to take it for write when creating pit.
This is in preparation to removing in_range and kvm->lock around it.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

KVM will inject a #GP into the guest if that tries to access unhandled
MSRs. This will crash many guests. Although it would be the correct
way to actually handle these MSRs, we introduce a runtime switchable
module param called "ignore_msrs" (defaults to 0). If this is Y, unknown
MSR reads will return 0, while MSR writes are simply dropped. In both cases
we print a message to dmesg to inform the user about that.

You can change the behaviour at any time by saying:

 # echo 1 > /sys/modules/kvm/parameters/ignore_msrs
Signed-off-by: NAndre Przywara <andre.przywara@amd.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

If the Linux kernel detects an C1E capable AMD processor (K8 RevF and
higher), it will access a certain MSR on every attempt to go to halt.
Explicitly handle this read and return 0 to let KVM run a Linux guest
with the native AMD host CPU propagated to the guest.
Signed-off-by: NAndre Przywara <andre.przywara@amd.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Linux tries to disable the flush filter on all AMD K8 CPUs. Since KVM
does not handle the needed MSR, the injected #GP will panic the Linux
kernel. Ignore setting of the HWCR.FFDIS bit in this MSR to let Linux
boot with an AMD K8 family guest CPU.
Signed-off-by: NAndre Przywara <andre.przywara@amd.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Correct missing locking in a few places in x86's vm_ioctl handling path.
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Add the opcodes for syscall, sysenter and sysexit to the list of instructions
handled by the undefined opcode handler.
Signed-off-by: NChristoph Egger <christoph.egger@amd.com>
Signed-off-by: NAmit Shah <amit.shah@redhat.com>
Signed-off-by: NAndre Przywara <andre.przywara@amd.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

This allows use of the powerful ftrace infrastructure.

See Documentation/trace/ for usage information.

[avi, stephen: various build fixes]
[sheng: fix control register breakage]
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NSheng Yang <sheng@linux.intel.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Replace previous exception with a new one in a hope that instruction
re-execution will regenerate lost exception.
Signed-off-by: NGleb Natapov <gleb@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

The performance counter MSRs are different for AMD and Intel CPUs and they
are chosen mainly by the CPUID vendor string. This patch catches writes to
all addresses (regardless of VMX/SVM path) and handles them in the generic
MSR handler routine. Writing a 0 into the event select register is something
we perfectly emulate ;-), so don't print out a warning to dmesg in this
case.
This fixes booting a 64bit Windows guest with an AMD CPUID on an Intel host.
Signed-off-by: NAndre Przywara <andre.przywara@amd.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

[christian: remove unused variables on s390]
Signed-off-by: NGleb Natapov <gleb@redhat.com>
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>