- 03 5月, 2014 6 次提交
-
-
由 Liam Girdwood 提交于
Read the stream offset and presentation position from DSP memory rather than using the old estimated position. This fixes timing issues with pulseaudio. Signed-off-by: NLiam Girdwood <liam.r.girdwood@linux.intel.com> Signed-off-by: NMark Brown <broonie@linaro.org>
-
由 Liam Girdwood 提交于
hw_params() can be called multiple times. Make sure we release the DSP stream that was allocated on previous hw_params() calls before allocating a new DSP stream. Signed-off-by: NLiam Girdwood <liam.r.girdwood@linux.intel.com> Signed-off-by: NMark Brown <broonie@linaro.org>
-
由 Liam Girdwood 提交于
The Intel IOMMU requires that the ACPI device is used to allocate all DMA memory buffers. This means we need to pass the DMA device pointer into child component devices that allocate DMA memory. We also only set the DMA mask for the ACPI device now instead of for each component device. Signed-off-by: NLiam Girdwood <liam.r.girdwood@linux.intel.com> Signed-off-by: NMark Brown <broonie@linaro.org>
-
由 Liam Girdwood 提交于
Fix page table creation on Haswell and Broadwell to remove unsafe virt_to_phys mappings and use more portable SG buffer. Use audio buffer APIs to allocate DMA buffers. Signed-off-by: NLiam Girdwood <liam.r.girdwood@linux.intel.com> Signed-off-by: NMark Brown <broonie@linaro.org>
-
由 Liam Girdwood 提交于
Make sure we add the allocated blocks to the modules list of blocks. Signed-off-by: NLiam Girdwood <liam.r.girdwood@linux.intel.com> Signed-off-by: NMark Brown <broonie@linaro.org>
-
由 Liam Girdwood 提交于
Make sure we dont alloc blocks twice with requests spanning more than one block. Signed-off-by: NLiam Girdwood <liam.r.girdwood@linux.intel.com> Signed-off-by: NMark Brown <broonie@linaro.org>
-
- 24 4月, 2014 1 次提交
-
-
由 Jarkko Nikula 提交于
I suppose there is a possibility that hsw_notification_work() may run after sst_hsw_stream_free() which can lead to a kernel crash since struct sst_hsw_stream is freed at that point and stream = container_of(work, struct sst_hsw_stream, notify_work) is not valid when hsw_notification_work() is run. Reported-by: NDerek Basehore <dbasehore@chromium.org> Reported-by: NWenkai Du <wenkai.du@intel.com> Signed-off-by: NJarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by: NMark Brown <broonie@linaro.org>
-
- 23 4月, 2014 2 次提交
-
-
由 Wenkai Du 提交于
There is a race between sst_byt_stream_free() and sst_byt_get_stream() if sst_byt_get_stream() called from sst_byt_irq_thread() context is accessing the byt->stream_list while a stream is deleted from the list. A stream is added to byt->stream_list in sst_byt_stream_new() and deleted in sst_byt_stream_free(). sst_byt_get_stream() is always protected by sst->spinlock, but the stream addition and deletion are not protected. The patch adds spinlock to both stream addition and deletion. [Jarkko: Same fix added to sst-haswell-ipc.c too] Signed-off-by: NWenkai Du <wenkai.du@intel.com> Signed-off-by: NJarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by: NMark Brown <broonie@linaro.org>
-
由 Wenkai Du 提交于
There were occasional ADSP crash during reboot testing: [ 11.883364] BUG: unable to handle kernel paging request at ffffc90121700000 [ 11.883380] IP: [<ffffffffc024d8bc>] sst_module_insert_fixed_block+0x24f/0x26d [snd_soc_sst_dsp] [ 11.883397] PGD 7800b067 PUD 0 [ 11.883405] Oops: 0002 [#1] SMP [ 11.886418] gsmi: Log Shutdown Reason 0x03 The virtual address, ffffc90121700000, was out of range. The virtual address is calculated by adding LPE base address with an offset: sst_memcpy32(dsp->addr.lpe + data->offset, data->data, data->size); The offset is calculated in sst_byt_parse_module, by subtraction of two virtual addresses dsp->addr.fw_ext and dsp->addr.lpe: block_data.offset = block->ram_offset + (dsp->addr.fw_ext - dsp->addr.lpe); These virtual addresses are assigned by kernel from ioremap: sst->addr.lpe = ioremap(pdata->lpe_base, pdata->lpe_size); sst->addr.fw_ext = ioremap(pdata->fw_base, pdata->fw_size); In current driver code, offset is defined as unsigned int32: struct sst_module_data { ... u32 offset; /* offset in FW file */ }; Most of the time kernel assigned virtual addresses with addr.fw_ext greater than addr.lpe. But sometimes it was the other way round. Fix the problem by declaring offset as signed int32_t. Signed-off-by: NWenkai Du <wenkai.du@intel.com> Signed-off-by: NJarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by: NMark Brown <broonie@linaro.org>
-
- 19 4月, 2014 2 次提交
-
-
由 Christian Engelmayer 提交于
Fix an incorrect sizeof() usage in sst_hsw_stream_get_volume(). sst_dsp_read() is called to read into a variable of type u32, but is passed sizeof(u32 *) for argument 'size_t bytes'. Detected by Coverity: CID 1195260. Signed-off-by: NChristian Engelmayer <cengelma@gmx.at> Signed-off-by: NMark Brown <broonie@linaro.org>
-
由 Dan Carpenter 提交于
The intent was to say "sizeof(*pos)" and not "sizeof(pos)". The sizeof(*pos) is 8 bytes so the bug won't show up on 64 bit systems. The sizeof(*dx) is 172 bytes so that will be a bugfix. Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com> Signed-off-by: NMark Brown <broonie@linaro.org>
-
- 10 4月, 2014 1 次提交
-
-
由 Tim Gardner 提交于
BugLink: http://bugs.launchpad.net/bugs/1305133 Malfunctioning or slow devices can cause a flood of dmesg SPAM. I've ignored checkpatch.pl complaints about the use of printk_ratelimit() in favour of prior art in sound/usb/pcm.c. WARNING: Prefer printk_ratelimited or pr_<level>_ratelimited to printk_ratelimit + if (printk_ratelimit() && Cc: Jaroslav Kysela <perex@perex.cz> Cc: Takashi Iwai <tiwai@suse.de> Cc: Eldad Zack <eldad@fogrefinery.com> Cc: Daniel Mack <zonque@gmail.com> Cc: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: NTim Gardner <tim.gardner@canonical.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 09 4月, 2014 5 次提交
-
-
由 Thierry Reding 提交于
The full_reset argument to azx_init_chip() carries boolean rather than numerical information, so update the type to reflect that. Signed-off-by: NThierry Reding <treding@nvidia.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Hui Wang 提交于
When we plug a 3-ring headset on the Dell machine (VID: 0x10ec0283, SID: 0x10280667), the headset mic can't be detected, after apply this patch, the headset mic can work well. BugLink: https://bugs.launchpad.net/bugs/1297581 Cc: David Henningsson <david.henningsson@canonical.com> Cc: stable@vger.kernel.org Signed-off-by: NHui Wang <hui.wang@canonical.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Christoph Jaeger 提交于
Eliminate boilerplate code by using module_platform_driver_probe(). Signed-off-by: NChristoph Jaeger <christophjaeger@linux.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Christoph Jaeger 提交于
Eliminate boilerplate code by using module_platform_driver(). Signed-off-by: NChristoph Jaeger <christophjaeger@linux.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Dylan Reid 提交于
From azx_interrupt, use the helper to check if the device is active instead of checking the state. This will do the right thing if runtime pm is disabled in addition to if the device is suspended. Signed-off-by: NDylan Reid <dgreid@chromium.org> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 08 4月, 2014 8 次提交
-
-
由 Takashi Iwai 提交于
PCM pointer callbacks in ice1712 driver check the buffer size boundary wrongly between bytes and frames. This leads to PCM core warnings like: snd_pcm_update_hw_ptr0: 105 callbacks suppressed ALSA pcm_lib.c:352 BUG: pcmC3D0c:0, pos = 5461, buffer size = 5461, period size = 2730 This patch fixes these checks to be placed after the proper unit conversions. Cc: <stable@vger.kernel.org> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Peter Ujfalusi 提交于
IB_NF, NB_IF and IB_IF configured the bc polarity incorrectly. The receive polarity was set to the same edge as the TX in these cases. Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: NMark Brown <broonie@linaro.org>
-
由 Sachin Kamat 提交于
PCM and S/PDIF drivers referenced mach headers for a trivial data structure. This caused build errors on multiplatform builds as machine headers are not accessible from driver files. Move the data structure definition to the driver header and remove the dependency. While at it rename the structure to avoid multiple definition errors as the same structure is also used by the platform code. Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org> Signed-off-by: NMark Brown <broonie@linaro.org>
-
由 Nicolin Chen 提交于
The BCP bit in TCR4/RCR4 register rules as followings: 0 Bit clock is active high with drive outputs on rising edge and sample inputs on falling edge. 1 Bit clock is active low with drive outputs on falling edge and sample inputs on rising edge. For all formats currently supported in the fsl_sai driver, they're exactly sending data on the falling edge and sampling on the rising edge. However, the driver clears this BCP bit for all of them which results click noise when working with SGTL5000 and big noise with WM8962. Thus this patch corrects the BCP settings for all the formats here to fix the nosie issue. Signed-off-by: NNicolin Chen <Guangyu.Chen@freescale.com> Acked-by: NXiubo Li <Li.Xiubo@freescale.com> Signed-off-by: NMark Brown <broonie@linaro.org>
-
由 Anssi Hannula 提交于
Currently stream numbers are assigned in reverse order. Unfortunately commit 7546abfb ("ALSA: hda - Increment default stream numbers for AMD HDMI controllers") assumed this was not the case (specifically, it had the "old cards had single device only" => "extra unused stream numbers do not matter" assumption), causing non-working audio regressions for AMD Radeon HDMI users. Change the stream numbers to be assigned in forward order. The benefit is that regular audio playback will still work even if the assumed stream count is too high, downside is that a too high stream count may remain hidden. Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=77002Reported-by: NChristian Güdel <cg@dmesg.ch> Signed-off-by: NAnssi Hannula <anssi.hannula@iki.fi> Tested-by: Christian Güdel <cg@dmesg.ch> # 3.14 Cc: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Kailang Yang 提交于
Add eapd shutup function to alc283_shutup. It could avoid pop noise from speaker. Signed-off-by: NKailang Yang <kailang@realtek.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Kailang Yang 提交于
Chrome OS was use model name of alc283-dac-wcaps for loading model as default. Change the model name to same as model name of Chrome OS for future support. Signed-off-by: NKailang Yang <kailang@realtek.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Uwe Kleine-König 提交于
If the renamed symbol is defined lib/iomap.c implements ioport_map and ioport_unmap and currently (nearly) all platforms define the port accessor functions outb/inb and friend unconditionally. So HAS_IOPORT_MAP is the better name for this. Consequently NO_IOPORT is renamed to NO_IOPORT_MAP. The motivation for this change is to reintroduce a symbol HAS_IOPORT that signals if outb/int et al are available. I will address that at least one merge window later though to keep surprises to a minimum and catch new introductions of (HAS|NO)_IOPORT. The changes in this commit were done using: $ git grep -l -E '(NO|HAS)_IOPORT' | xargs perl -p -i -e 's/\b((?:CONFIG_)?(?:NO|HAS)_IOPORT)\b/$1_MAP/' Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: NArnd Bergmann <arnd@arndb.de> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 07 4月, 2014 3 次提交
-
-
由 Axel Lin 提交于
DA732X_ID_MAJOR_MASK is 0xF0, so the major id is (reg & DA732X_ID_MAJOR_MASK) >> 4. Signed-off-by: NAxel Lin <axel.lin@ingics.com> Acked-by: NAdam Thomson <Adam.Thomson.Opensource@diasemi.com> Signed-off-by: NMark Brown <broonie@linaro.org>
-
由 Kailang Yang 提交于
It is better to change Mic2-Vref to manual mode. Manual control Mic2-Vref will solve pop noise issue. It will improve pop noise for power on, power off, S3 and resume. Signed-off-by: NKailang Yang <kailang@realtek.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Axel Lin 提交于
BIT[0:2] of register 01h is REVID, so the mask for REVID should be 0x7. Also updates the code to use CS42L52_CHIP_REV_MASK. Signed-off-by: NAxel Lin <axel.lin@ingics.com> Acked-by: NBrian Austin <brian.austin@cirrus.com> Signed-off-by: NMark Brown <broonie@linaro.org>
-
- 05 4月, 2014 1 次提交
-
-
由 Joe Perches 提交于
Most of it duplicates function tracing and one of them has an uncompilable printf %P use. Others have format/argument mismatches. Remove unused DBG1 macro definition Neaten uart401.c use of ok test around this DBG macro removal. Signed-off-by: NJoe Perches <joe@perches.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 04 4月, 2014 4 次提交
-
-
由 Ondrej Zary 提交于
Save/restore routing and rate registers during suspend/resume. This fixes S/PDIF input being disabled after resume. Tested with Audiophile 24/96. Signed-off-by: NOndrej Zary <linux@rainbow-software.org> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Ondrej Zary 提交于
Also restore AK4xxx mixer volumes on resume for M-Audio ICE1712-based cards. This fixes incorrect (sound working) zero mixer volumes after resume. Signed-off-by: NOndrej Zary <linux@rainbow-software.org> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Christoph Jaeger 提交于
Commit 5d6be5aa ("ASoC: codec: Simplify ASoC probe code.") left variable 'ret', whose value is returned, uninitialized. Since it is not used otherwise, remove it. Signed-off-by: NChristoph Jaeger <christophjaeger@linux.com> Signed-off-by: NMark Brown <broonie@linaro.org>
-
由 Axel Lin 提交于
Fix checking return value of regmap_read(). Also fix reporting the chip_id value. CS42XX8_CHIPID_CHIP_ID_MASK is 0xF0, so the chip_id value is (val & CS42XX8_CHIPID_CHIP_ID_MASK) >> 4). Signed-off-by: NAxel Lin <axel.lin@ingics.com> Acked-by: NPaul Handrigan <paul.handrigan@cirrus.com> Acked-by: NBrian Austin <brian.austin@cirrus.com> Acked-by: NNicolin Chen <Guangyu.Chen@freescale.com> Signed-off-by: NMark Brown <broonie@linaro.org>
-
- 03 4月, 2014 4 次提交
-
-
由 Ondrej Zary 提交于
Add S/PDIF suspend support for M-Audio cards based on ICE1712 chip. Tested (playback only) on Audiophile 24/96. Capture will probably not work. Signed-off-by: NOndrej Zary <linux@rainbow-software.org> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Ondrej Zary 提交于
Separate HW initialization from device creation. This is needed for suspend/resume support. Signed-off-by: NOndrej Zary <linux@rainbow-software.org> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Takashi Iwai 提交于
The recent fixups for HP laptops to support the mute LED made the speaker output silent on some machines. It turned out that they use the NID 0x18 for the speaker while it's also used for controlling the LED via VREF bits although the current driver code blindly assumes that such a node is a mic pin (where 0x18 is usually so). This patch fixes the problem by only changing the VREF bits and keeping the other pin ctl bits. Reported-and-tested-by: NHui Wang <hui.wang@canonical.com> Cc: <stable@vger.kernel.org> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Kailang Yang 提交于
If it only has single output of HP out of machine. The driver parser will copy hp_pins to line_out_pins. hp_pins will empty for alc283_init and alc283_shutup functions. This will cause not have value for hp_pin_sense. Add check line_out_type code will solve it . Signed-off-by: NKailang Yang <kailang@realtek.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 01 4月, 2014 3 次提交
-
-
由 Stephen Warren 提交于
Add a device tree match table. This serves to make the driver's support of device tree more explicit. Perhaps the fallback for DT matching to using the i2c_device_id table will go away one day, since it fails in face of devices from different vendors with the same name. Signed-off-by: NStephen Warren <swarren@nvidia.com> Signed-off-by: NMark Brown <broonie@linaro.org>
-
由 Stephen Warren 提交于
Add a device tree match table. This serves to make the driver's support of device tree more explicit. Perhaps the fallback for DT matching to using the i2c_device_id table will go away one day, since it fails in face of devices from different vendors with the same name. Signed-off-by: NStephen Warren <swarren@nvidia.com> Signed-off-by: NMark Brown <broonie@linaro.org>
-
由 Stephen Warren 提交于
Add a device tree match table. This serves to make the driver's support of device tree more explicit. Perhaps the fallback for DT matching to using the i2c_device_id table will go away one day, since it fails in face of devices from different vendors with the same name. Signed-off-by: NStephen Warren <swarren@nvidia.com> Signed-off-by: NMark Brown <broonie@linaro.org>
-