The S2MPS15 PMIC is similar in functionality to S2MPS11/14 PMIC. It contains
27 LDO and 10 Buck regulators and allows programming these regulators via a
I2C interface. This patch adds initial support for LDO/Buck regulators of
S2MPS15 PMIC.
Signed-off-by: NThomas Abraham <thomas.ab@samsung.com>
Signed-off-by: NAlim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: NMark Brown <broonie@kernel.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The driver depends on MFD_STW481X but there isn't a build dependency so
it's a good idea to allow the driver to always be built when the
COMPILE_TEST option is enabled.

That way, the driver can be built with a config generated by make
allyesconfig and check if a patch would break the build.
Signed-off-by: NLuis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Driver for regulators exposed by the Resource Power Manager (RPM) found
in devices based on Qualcomm 8974 and newer platforms.
Signed-off-by: NBjorn Andersson <bjorn.andersson@sonymobile.com>
Acked-by: NAndy Gross <agross@codeaurora.org>
Tested-by: NTim Bird <tim.bird@sonymobile.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Add regulator support for mt6311.
It has 2 regulaotrs - Buck and LDO, provide the related buck/ldo voltage
data to the driver, and creates the regulator_desc table. Supported
operations for Buck are enabled/disabled and voltage change, only
enabled/disabled for LDO.
Signed-off-by: NHenry Chen <henryc.chen@mediatek.com>
Reviewed-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The max77693 regulator driver supports Maxim 77843 device so remove the
max77843 driver.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The charger and safeout parts of MAX77843 are almost the same as MAX77693.
From regulator point of view the only differences are the constraints
and register values related to these constraints. Now the max77693
regulator driver can be used for MAX77843 device.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski.k@gmail.com>
Acked-by: NMark Brown <broonie@kernel.org>
Signed-off-by: NMark Brown <broonie@kernel.org>

This is a patch for supporting da9215 buck converter.
Signed-off-by: NJames Ban <james.ban.opensource@diasemi.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Add an SPMI regulator driver for Qualcomm's PM8841, PM8941, and
PM8916 PMICs. This driver is based largely on code from
codeaurora.org[1].

[1] https://www.codeaurora.org/cgit/quic/la/kernel/msm-3.10/tree/drivers/regulator/qpnp-regulator.c?h=msm-3.10
Cc: David Collins <collinsd@codeaurora.org>
Cc: <devicetree@vger.kernel.org>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NMark Brown <broonie@kernel.org>

Add BUCK and LDO regulator driver support for DA9062
Signed-off-by: NSteve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.

Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NMark Brown <broonie@kernel.org>

This patch adds new regulator driver to support max77843
MFD(Multi Function Device) chip`s regulators.
The Max77843 has two voltage regulators for USB safeout.
Signed-off-by: NJaewon Kim <jaewon02.kim@samsung.com>
Signed-off-by: NBeomho Seo <beomho.seo@samsung.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Add MT6397 regulator driver.
Signed-off-by: NFlora Fu <flora.fu@mediatek.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

This patch adds S2MPS13 regulator device to existing S2MPS11 device driver.
The S2MPS13 has just different number of regulators from S2MPS14.
The S2MPS13 regulator device includes LDO[1-40] and BUCK[1-10].
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Acked-by: NSangbeom Kim <sbkim73@samsung.com>
Acked-by: NMark Brown <broonie@kernel.org>
Reviewed-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Signed-off-by: NGyungoh Yoo <jack.yoo@skyworksinc.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

This patch add device driver of Richtek RT5033 PMIC.
The driver support multiple regulator like LDO and synchronous Buck.
The integrated synchronous buck converter is designed to provide 0.6 A
application with high efficiency. Two LDOs are integrated. One safe LDO is
for 60mA and the other one LDO is for 150 mA.

Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: NBeomho Seo <beomho.seo@samsung.com>
Acked-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

rename st-pwm to pwm-regulator. And support getting voltage & duty table from
device tree, other platforms can also use this driver without any modify.
Signed-off-by: NChris Zhong <zyw@rock-chips.com>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Tested-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NMark Brown <broonie@kernel.org>

Driver for regulators exposed by the Resource Power Manager (RPM) found
in Qualcomm 8660, 8960 and 8064 based devices.
Signed-off-by: NBjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Fix ERROR: "devm_regmap_init_i2c" [drivers/regulator/isl9305.ko] undefined!
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The ISL9305 and ISL9305H are mini-PMICs offering two DCDC regulators and
two LDO regulators. While there are some register differences between them
these do not affect the current Linux driver as the relevant features are
not yet supported.
Signed-off-by: NMark Brown <broonie@kernel.org>

This driver supports the 3 DCDC and 7 LDO regulators available on
Ricoh RN5T618 PMIC.
Signed-off-by: NBeniamino Galvani <b.galvani@gmail.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

The regulator module consists of 4 DCDCs, 8 LDOs and 2 switches.
The output voltages are configurable and are meant to supply power
to the main processor and other components
Signed-off-by: NChris Zhong <zyw@rock-chips.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

The MAX77802 PMIC has 10 high-efficiency Buck and 32 Low-dropout
(LDO) regulators. This patch adds support for all these regulators
found on the MAX77802 PMIC and is based on a driver added by Simon
Glass to the Chrome OS kernel 3.8 tree.
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: NNaveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Add driver support for HiSilicon Hi6421 voltage regulators.

Two rules for regulator enabling are defined in hi6421 spec:
1) Between disable and enable of each regulator (LDOs or BUCKs), there must
   be a protection gap. Use @off_on_delay of regulator core to implement this.
2) No two regulators can be enabled at the same time. Use mutex in
   hi6421_regulator_pdata to ensure this. A protection gap of 100us is added
   into each LDO/BUCK's .enable_time.
Signed-off-by: NGuodong Xu <guodong.xu@linaro.org>
Signed-off-by: NMark Brown <broonie@linaro.org>

Signed-off-by: NGyungoh Yoo <jack.yoo@skyworksinc.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

This is a patch for supporting DA9213.
Signed-off-by: NJames Ban <james.ban.opensource@diasemi.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

This driver also supports S2MPU02 now, thus update module description and
Kconfig accordingly.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

This is the driver for the Dialog DA9211 Multi-phase 12A DC-DC Buck
Converter regulator. It communicates via an I2C bus to the device.
Signed-off-by: NJames Ban <james.ban.opensource@diasemi.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Make this driver depend on I2C and select REGMAP_I2C to fix build failure.
Also allows this driver to be built as module.
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Acked-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

This patch adds support for the Linear Technology LTC3589, LTC3589-1,
and LTC3589-2 8-output I2C voltage regulator ICs.
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

Add support for MAX77836 chipset and its additional two LDO regulators.
These LDO regulators are controlled by the PMIC block with additional
regmap (different I2C slave address).

The MAX77836 charger and safeout regulators are almost identical to
MAX14577. The registers layout is the same, except values for charger's
current. The patch adds simple mapping between device type and supported
current by the charger regulator.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: NMark Brown <broonie@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

AXP202 and AXP209 come with two synchronous step-down DC-DCs and five
LDOs. This patch introduces basic support for those regulators.
Signed-off-by: NCarlo Caione <carlo@caione.org>
Signed-off-by: NMark Brown <broonie@linaro.org>

On some STMicroelectronics hardware reside regulators consisting
partly of a PWM input connected to the feedback loop. As the PWM
duty-cycle is varied the output voltage adapts. This driver
allows us to vary the output voltage by adapting the PWM input
duty-cycle.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NMark Brown <broonie@linaro.org>

Add support for S2MPS14 PMIC regulators to s2mps11 driver. The S2MPS14
has fewer BUCK-s and LDO-s than S2MPS11. It also does not support
controlling the BUCK ramp delay.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Reviewed-by: NYadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Add support for S2MPA01 voltage and current regulator.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Acked-by: NMark Brown <broonie@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Add a regulator driver for the BCM590xx PMU voltage regulators.
The driver supports LDOs and DCDCs in normal mode only. There is
no support for low-power mode or power sequencing.
Signed-off-by: NMatt Porter <mporter@linaro.org>
Reviewed-by: NTim Kryger <tim.kryger@linaro.org>
Reviewed-by: NMarkus Mayer <markus.mayer@linaro.org>
Signed-off-by: NMark Brown <broonie@linaro.org>

Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Acked-by: NRobin Gong <b38343@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

pbias register controls internal power supply to sd card i/o pads
in most OMAPs (OMAP2-5, DRA7).
Control bits for selecting voltage level and
enabling/disabling are in the same PBIAS register.
Signed-off-by: NBalaji T K <balajitk@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Acked-by: NMark Brown <broonie@linaro.org>
Tested-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Tested-by: NStefan Roese <sr@denx.de>
Signed-off-by: NChris Ball <chris@printf.net>

This is a DT-only driver, so make it depend on OF and remove of_match_ptr in
the code.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Acked-by: NKeerthy <j-keerthy@ti.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

This patch adds support for TPS65218 PMIC regulators.

The regulators set consists of 6 DCDCs and 1 LDO. The output
voltages are configurable and are meant to supply power to the
main processor and other components.
Signed-off-by: NKeerthy <j-keerthy@ti.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Symbol MFD_MC13783 always selected by MFD_MC13XXX, so no need
to keep additional symbol.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NLee Jones <lee.jones@linaro.org>