This patch fixes a possible problem in the resume from
hibenration. It temporaneally saves the clk->rate on the
stack to avoid any possible change during the clk->set_parent(..)
call.
Signed-off-by: NFrancesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds suspend/resume support to the LCDC
driver for SuperH Mobile - sh_mobile_lcdcfb.

We simply stop hardware on suspend and start it again
on resume. For RGB panels this is trivial, but for SYS
panels in deferred io mode this becomes a bit more
difficult - we need to wait for a frame end interrupt
to make sure the clocks are balanced before stopping
the actual hardware.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Improve the ap325 board code to allow the lcd panel
and backlight to be powered off.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch contains CONFIG_SUSPEND support to the SuperH
architecture. If enabled, SuperH Mobile processors will
register their suspend callbacks during boot.

To suspend, use "echo mem > /sys/power/state". To allow
wakeup, make sure "/sys/device/platform/../power/wakeup"
contains "enabled". Additional per-device driver patches
are most likely needed.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

-- log --
arch/sh/kernel/cpu/sh4/../sh3/entry.S:365: Error: invalid operands for opcode
make[4]: *** [arch/sh/kernel/cpu/sh4/../sh3/entry.o] Error 1
make[3]: *** [arch/sh/kernel/cpu/sh4] Error 2
-- log --
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

dma-sh's get_dma_error_irq() is only used by SH4, as the SH3
doesn't have the DMA Error interrupt.

Disable it out for non-SH4 builds.
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This implements preliminary suspend/resume support for the PMB.
Signed-off-by: NFrancesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NNobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Improve the sh7785lcr power off implementation to
never return. It takes some time before the board
is actually powered off, just hang after asking
the harware to power down.

This removes the serial port garbage printout.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch changes sh_keysc to use to_platform_device()
for suspend. Thanks to Trilok Soni for this suggestion.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Reviewed-by: NTrilok Soni <soni.trilok@gmail.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds PM support to the clock framework.
With this, resume from hibernation is properly supported.
Signed-off-by: NFrancesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds the clk_set_parent/clk_get_parent routines to the sh
clock framework.
Signed-off-by: NFrancesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds support for the Sega Dreamcast visual memory unit as a
flash mapping. It requires changes in the maple bus driver (posted
separately) to support block reads and writes.

The VMU is a 'smart' flash device, with a built-in 8-bit controller -
for instance there is an erase before a write but it is hidden from the
user. But the device's overall behaviour means it works well with the
mtd layer and it is appropriate to add it as an mtd mapping.
Signed-off-by: NAdrian McMenamin <adrian@mcmen.demon.co.uk>
Acked-By: NDavid Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This adds DMA support for newer SH-4A CPUs, particularly SH7763/64/80/85.

This also enables multi IRQ support for platforms that have multiple
vectors bound to the same IRQ source.
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Fix the problem that cannot work a PCI device when 32-bit physical
address mode.
Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add a new defconfig for SH7785LCR in 32-bit mode, and update the power
off code to avoid 29-bit assumptions.
Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This provides a method for supporting fixed PMB mappings inherited from
the bootloader, as an alternative to the dynamic PMB mapping currently
used by the kernel. In the future these methods will be combined.

P1/P2 area is handled like a regular 29-bit physical address, and local
bus device are assigned P3 area addresses.
Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds wakeup support to the sh_keysc driver.
With this feature the ".../power/wakeup" file can be
used to enable and disable if the device takes the
system out of suspend. Default is enabled.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

If CONFIG_PM is set, let Migo-R LEDs show sleep states.
D11 will show STATUS0 and D12 PDSTATUS.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Fix deferred io cleanup patch in the sh_mobile_lcdcfb driver.

If probe() fails early the sh_mobile_lcdc_stop() function will
be called to clean up deferred io. This patch modifies the
code to only call fb_deferred_io_cleanup() after deferred io
has been initialized.

With this patch applied we no longer hit BUG_ON() inside
fb_deferred_io_cleanup(). Triggers on a Migo-R with the
SYS QVGA panel board unmounted.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Other compilation errors were revised by commit of
"sh: ap325rxa: Revert ov772x support"
(08c2f5b4) but other compilation
errors are given.
We revert this commit and need to add new header(media/soc_camera.h).
This change revises new compilation error.
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add Suspend-to-disk / swsusp / CONFIG_HIBERNATION support
to the SuperH architecture.

To suspend, use "swapon /dev/sda2; echo disk > /sys/power/state"
To resume, pass "resume=/dev/sda2" on the kernel command line.

The patch "pm: rework includes, remove arch ifdefs V2" is
needed to allow the generic swsusp code to build properly.

Hibernation is not enabled with this patch though, a patch
setting ARCH_HIBERNATION_POSSIBLE will be submitted later.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
  [CPUFREQ] Add p4-clockmod sysfs-ui removal to feature-removal schedule.
  Revert "[CPUFREQ] Disable sysfs ui for p4-clockmod."

CLONE_PARENT can fool the ->self_exec_id/parent_exec_id logic. If we
re-use the old parent, we must also re-use ->parent_exec_id to make
sure exit_notify() sees the right ->xxx_exec_id's when the CLONE_PARENT'ed
task exits.

Also, move down the "p->parent_exec_id = p->self_exec_id" thing, to place
two different cases together.
Signed-off-by: NOleg Nesterov <oleg@redhat.com>
Cc: Roland McGrath <roland@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Serge E. Hallyn <serge@hallyn.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NDave Jones <davej@redhat.com>

This reverts commit e088e4c9.

Removing the sysfs interface for p4-clockmod was flagged as a
regression in bug 12826.

Course of action:
 - Find out the remaining causes of overheating, and fix them
   if possible. ACPI should be doing the right thing automatically.
   If it isn't, we need to fix that.
 - mark p4-clockmod ui as deprecated
 - try again with the removal in six months.

It's not really feasible to printk about the deprecation, because
it needs to happen at all the sysfs entry points, which means adding
a lot of strcmp("p4-clockmod".. calls to the core, which.. bleuch.
Signed-off-by: NDave Jones <davej@redhat.com>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (29 commits)
  p54: fix race condition in memory management
  cfg80211: test before subtraction on unsigned
  iwlwifi: fix error flow in iwl*_pci_probe
  rt2x00 : more devices to rt73usb.c
  rt2x00 : more devices to rt2500usb.c
  bonding: Fix device passed into ->ndo_neigh_setup().
  vlan: Fix vlan-in-vlan crashes.
  net: Fix missing dev->neigh_setup in register_netdevice().
  tmspci: fix request_irq race
  pkt_sched: act_police: Fix a rate estimator test.
  tg3: Fix 5906 link problems
  SCTP: change sctp_ctl_sock_init() to try IPv4 if IPv6 fails
  IPv6: add "disable" module parameter support to ipv6.ko
  sungem: another error printed one too early
  aoe: error printed 1 too early
  net pcmcia: worklimit reaches -1
  net: more timeouts that reach -1
  net: fix tokenring license
  dm9601: new vendor/product IDs
  netlink: invert error code in netlink_set_err()
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
  lguest: fix for CONFIG_SPARSE_IRQ=y
  lguest: fix crash 'unhandled trap 13 at <native_read_msr_safe>'

* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
  Btrfs: fix spinlock assertions on UP systems

btrfs_tree_locked was being used to make sure a given extent_buffer was
properly locked in a few places.  But, it wasn't correct for UP compiled
kernels.

This switches it to using assert_spin_locked instead, and renames it to
btrfs_assert_tree_locked to better reflect how it was really being used.
Signed-off-by: NChris Mason <chris.mason@oracle.com>

Frans Pop reported the crash below when running an s390 kernel under Hercules:

  Kernel BUG at 000738b4  verbose debug info unavailable!
  fixpoint divide exception: 0009  #1! SMP
  Modules linked in: nfs lockd nfs_acl sunrpc ctcm fsm tape_34xx
     cu3088 tape ccwgroup tape_class ext3 jbd mbcache dm_mirror dm_log dm_snapshot
     dm_mod dasd_eckd_mod dasd_mod
  CPU: 0 Not tainted 2.6.27.19 #13
  Process awk (pid: 2069, task: 0f9ed9b8, ksp: 0f4f7d18)
  Krnl PSW : 070c1000 800738b4 (acct_update_integrals+0x4c/0x118)
             R:0 T:1 IO:1 EX:1 Key:0 M:1 W:0 P:0 AS:0 CC:1 PM:0
  Krnl GPRS: 00000000 000007d0 7fffffff fffff830
             00000000 ffffffff 00000002 0f9ed9b8
             00000000 00008ca0 00000000 0f9ed9b8
             0f9edda4 8007386e 0f4f7ec8 0f4f7e98
  Krnl Code: 800738aa: a71807d0         lhi     %r1,2000
             800738ae: 8c200001         srdl    %r2,1
             800738b2: 1d21             dr      %r2,%r1
            >800738b4: 5810d10e         l       %r1,270(%r13)
             800738b8: 1823             lr      %r2,%r3
             800738ba: 4130f060         la      %r3,96(%r15)
             800738be: 0de1             basr    %r14,%r1
             800738c0: 5800f060         l       %r0,96(%r15)
  Call Trace:
  ( <000000000004fdea>! blocking_notifier_call_chain+0x1e/0x2c)
    <0000000000038502>! do_exit+0x106/0x7c0
    <0000000000038c36>! do_group_exit+0x7a/0xb4
    <0000000000038c8e>! SyS_exit_group+0x1e/0x30
    <0000000000021c28>! sysc_do_restart+0x12/0x16
    <0000000077e7e924>! 0x77e7e924

Reason for this is that cpu time accounting usually only happens from
interrupt context, but acct_update_integrals gets also called from
process context with interrupts enabled.

So in acct_update_integrals we may end up with the following scenario:

Between reading tsk->stime/tsk->utime and tsk->acct_timexpd an interrupt
happens which updates accouting values.  This causes acct_timexpd to be
greater than the former stime + utime.  The subsequent calculation of

	dtime = cputime_sub(time, tsk->acct_timexpd);

will be negative and the division performed by

	cputime_to_jiffies(dtime)

will generate an exception since the result won't fit into a 32 bit
register.

In order to fix this just always disable interrupts while accessing any
of the accounting values.

Reported by: Frans Pop <elendil@planet.nl>
Tested by: Frans Pop <elendil@planet.nl>
Cc: stable@kernel.org
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Impact: remove lots of lguest boot WARN_ON() when CONFIG_SPARSE_IRQ=y

We now need to call irq_to_desc_alloc_cpu() before
set_irq_chip_and_handler_name(), but we can't do that from init_IRQ (no
kmalloc available).

So do it as we use interrupts instead.  Also means we only alloc for
irqs we use, which was the intent of CONFIG_SPARSE_IRQ anyway.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@redhat.com>

Impact: fix lguest boot crash on modern Intel machines

The code in early_init_intel does:

	if (c->x86 > 6 || (c->x86 == 6 && c->x86_model >= 0xd)) {
		u64 misc_enable;

		rdmsrl(MSR_IA32_MISC_ENABLE, misc_enable);

And that rdmsr faults (not allowed from non-0 PL).  We can get around
this by mugging the family ID part of the cpuid.  5 seems like a good
number.

Of course, this is a hack (how very lguest!).  We could just indicate
that we don't support MSRs, or implement lguest_rdmst.
Reported-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Tested-by: NPatrick McHardy <kaber@trash.net>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
  mmc: fix data timeout for SEND_EXT_CSD