Move the corresponding code for setting the initial signal voltage, from
mmc_power_up() into a new function, mmc_set_initial_signal_voltage().

Make the function internally available to the mmc core, as to allow the
following changes to make use of it.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Tested-by: NQuentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: NShawn Lin <shawn.lin@rock-chips.com>

It's rather common that a firmware is loaded into an SDIO func device
memory, by the corresponding SDIO func driver during ->probe() time.

However, to actually start running the new firmware, sometimes a soft reset
(no power cycle) and a re-initialization of the card is needed. This is for
example the case with the Espressif ESP8089 WiFi chips, when connected to
an SDIO interface.

To cope with this scenario, let's add a new exported function,
mmc_sw_reset(), which may be called when a soft reset and re-initialization
of the card are needed.

The mmc_sw_reset() is implemented on top of a new bus ops callback, similar
to how the mmc_hw_reset() has been implemented.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Tested-by: NQuentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: NShawn Lin <shawn.lin@rock-chips.com>

The bus ops ->reset() executes a full HW reset of the card, as the calling
function mmc_hw_reset() also indicates by its name. Let's convert to follow
the similar names, for both the bus ops callback and for the corresponding
bus ops functions, as to clarify the purpose of code.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Tested-by: NQuentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: NShawn Lin <shawn.lin@rock-chips.com>

The mmc_sdio_init_card() function has a couple of callers. In the
re-initialization cases, some additional reset commands are issued before
mmc_sdio_init_card() is called. As these additional reset commands are the
same, let's move these into a new static function, mmc_sdio_reinit_card()
and call mmc_sdio_init_card() from there. In this way we avoid the open
coding.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Tested-by: NQuentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: NShawn Lin <shawn.lin@rock-chips.com>

Allow to use tunable delay before detecting card after card is inserted,
which either comes from firmware node, or comes from debounce value
passed on to mmc_gpiod_request_cd(). If the platform doesn't support
debounce, then we fall back to use the debounce period as the delay,
otherwise, it behaves the same as before that a HW debounce(if set) plus
a 200ms hardcode delay before detecting the card.
Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Some SD host controllers cannot handle extended use of 3.3V signaling.
To accommodate these controllers, add a capability that requires us to
negotiate the voltage down from 3.3V during card initialization.
Signed-off-by: NKyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: NJennifer Dahm <jennifer.dahm@ni.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This patch uses limit clock rate quirk to reduce clock rate
for "SDR104" mode on IMX side for Marvell 8887
WiFi + Bluetooth chip side, as Marvell does not recommend
to use SDIO at the speed of higher than 150MHz.
Signed-off-by: NDiwakar Sharma <diwakar.sharma@in.bosch.com>
Signed-off-by: NHarish Jenny K N <harish_kandiga@mentor.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This patch adds a quirk to limit clock rate which
can be used to reduce the SDIO clock rate for some
chips with broken UHS.
Signed-off-by: NHarish Jenny K N <harish_kandiga@mentor.com>
Reviewed-by: NShawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Since RPMB area is accessible via special ioctl only and boot areas
are unlikely to contain any partitions, exclude them all from listing
in /proc/partitions. This will hide them from various user-level
software (e.g. fdisk), thus avoiding unnecessary access attempts.
Signed-off-by: NAndrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: NHarish Jenny K N <harish_kandiga@mentor.com>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The use of stack Variable Length Arrays needs to be avoided, as they
can be a vector for stack exhaustion, which can be both a runtime bug
(kernel Oops) or a security flaw (overwriting memory beyond the
stack). Also, in general, as code evolves it is easy to lose track of
how big a VLA can get. Thus, we can end up having runtime failures
that are hard to debug. As part of the directive[1] to remove all VLAs
from the kernel, and build with -Wvla.

Currently driver is using a VLA declared using the number of descriptors.  This
array is used to store integer values and is later used as an argument to
`gpiod_set_array_value_cansleep()` This can be avoided by using
`kmalloc_array()` to allocate memory for the array of integer values.  Memory is
free'd before return from function.

>From the code it appears that it is safe to sleep so we can use GFP_KERNEL
(based _cansleep() suffix of function `gpiod_set_array_value_cansleep()`.

It can be expected that this patch will result in a small increase in overhead
due to the use of `kmalloc_array()`

[1] https://lkml.org/lkml/2018/3/7/621Signed-off-by: NTobin C. Harding <me@tobin.cc>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Upon module load, mmc_block allocates a bus with bus_registeri() in
mmc_blk_init(). This reference never gets freed during module unload, which
leads to subsequent re-insertions of the module fails and a WARN() splat is
triggered.

Fix the bug by dropping the reference for the bus in mmc_blk_exit().
Signed-off-by: NAlexander Kappner <agk@godking.net>
Fixes: 97548575 ("mmc: block: Convert RPMB to a character device")
Cc: <stable@vger.kernel.org>
Reviewed-by: NShawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

dd if=/dev/urandom of=/dev/mmcblk1 bs=4k count=10000
with a SD card hotplug during transfer reports a warning below
introduced by commit a063057d ("block: Fix a race between
request queue removal and the block cgroup controller"). So we
should now remove the disk, partition and bdi sysfs attributes
before cleaning up the request queue associated with the disk.

[  410.331226] mmc1: card 59b4 removed
[  410.348583] WARNING: CPU: 0 PID: 5 at block/blk-core.c:785
blk_cleanup_queue+0x138/0x140
[  410.349294] Modules linked in:
[  410.349570] CPU: 0 PID: 5 Comm: kworker/0:0 Not tainted
4.16.0-rc6-next-20180321-00004-gc2ad6a7 #263
[  410.350363] Hardware name: Excavator-RK3399 Board (DT)
[  410.350819] Workqueue: events_freezable mmc_rescan
[  410.351242] pstate: 60000005 (nZCv daif -PAN -UAO)
[  410.351663] pc : blk_cleanup_queue+0x138/0x140
[  410.352054] lr : blk_cleanup_queue+0xac/0x140
[  410.352436] sp : ffff0000092cbb90
[  410.352727] x29: ffff0000092cbb90 x28: 0000000000000000
[  410.353195] x27: ffff8000f6f23030 x26: ffff00000904e610
[  410.353662] x25: ffff8000f17cc808 x24: ffff8000f1038200
[  410.354128] x23: 0000000000000060 x22: 0000000000000000
[  410.354595] x21: ffff8000f11748d8 x20: ffff8000f1038200
[  410.355061] x19: ffff8000f1174200 x18: 0000ffff936347d8
[  410.355528] x17: 0000ffff935b93c0 x16: ffff0000081263f8
[  410.355994] x15: 0000000000000000 x14: 0000000000000400
[  410.356461] x13: 0000000000000001 x12: 0000000000000001
[  410.356927] x11: 0000000000000040 x10: ffff8000f2400028
[  410.357393] x9 : ffff8000f2400040 x8 : 0000000000000000
[  410.357860] x7 : ffff8000f6f3a340 x6 : ffff8000f6f3a340
[  410.358326] x5 : ffff8000f2400000 x4 : ffff8000f6f3a340
[  410.358792] x3 : 0000000000000000 x2 : 39c1333e45670800
[  410.359259] x1 : 0000000000000000 x0 : 0000000000000003
[  410.359726] Call trace:
[  410.359943]  blk_cleanup_queue+0x138/0x140
[  410.360305]  mmc_cleanup_queue+0x2c/0x48
[  410.360652]  mmc_blk_remove_req+0x1c/0x98
[  410.361005]  mmc_blk_remove+0x180/0x1c0
[  410.361343]  mmc_bus_remove+0x1c/0x28
[  410.361670]  device_release_driver_internal+0x154/0x1f0
[  410.362128]  device_release_driver+0x14/0x20
[  410.362504]  bus_remove_device+0xc8/0x108
[  410.362858]  device_del+0x120/0x350
[  410.363167]  mmc_remove_card+0x5c/0xb8
[  410.363498]  mmc_sd_detect+0x40/0x78
[  410.363813]  mmc_rescan+0x19c/0x368
[  410.364123]  process_one_work+0x1ac/0x318
[  410.364477]  worker_thread+0x50/0x450
[  410.364801]  kthread+0xf8/0x128
[  410.365081]  ret_from_fork+0x10/0x18
[  410.365395] ---[ end trace 268e87a46c28968c ]---
Reviewed-by: NBart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Update documentation for sdio_claim_irq to downgrade the wording
about doing recursive claims in an IRQ handler from 'must not' to
'should not'. This clarifies that recursive claims are supported,
but not the recommended (best) practice
Signed-off-by: NJoel Cunningham <joel.cunningham@garmin.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This patch exports the host capabilities to debugfs
Signed-off-by: NAbbas Raza <Abbas_Raza@mentor.com>
Signed-off-by: NAndrew Gabbasov <andrew_gabbasov@mentor.com>
[Harish: Added caps2, moved creation to mmc_add_host_debugfs]
Signed-off-by: NHarish Jenny K N <harish_kandiga@mentor.com>
Reviewed-by: NShawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Certain Micron eMMC v4.5 cards might get broken when HPI feature is used
and hence this patch disables the HPI feature for such buggy cards.

In U-Boot, these cards are reported as

Manufacturer: Micron (ID: 0xFE)
OEM: 0x4E
Name: MMC32G
Revision: 19 (0x13)
Serial: 959241022  Manufact. date: 8/2015 (0x82)  CRC: 0x00
Tran Speed: 52000000
Rd Block Len: 512
MMC version 4.5
High Capacity: Yes
Capacity: 29.1 GiB
Boot Partition Size: 16 MiB
Bus Width: 8-bit

According to JEDEC JEP106 manufacturer 0xFE is Numonyx, which was bought by
Micron.
Signed-off-by: NDirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: NMark Craske <Mark_Craske@mentor.com>
Cc: <stable@vger.kernel.org> # 4.8+
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

PARTITION_CONFIG is cached in mmc_card->ext_csd.part_config and the
currently active partition in mmc_blk_data->part_curr. These caches do
not always reflect changes if the ioctl call modifies the
PARTITION_CONFIG registers, e.g. by changing BOOT_PARTITION_ENABLE.

Write the PARTITION_CONFIG value extracted from the ioctl call to the
cache and update the currently active partition accordingly. This
ensures that the user space cannot change the values behind the
kernel's back. The next call to mmc_blk_part_switch() will operate on
the data set by the ioctl and reflect the changes appropriately.
Signed-off-by: NBastian Stender <bst@pengutronix.de>
Signed-off-by: NJan Luebbe <jlu@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This patch exports RCA register to sysfs which will help in reading the
disk identification information.
Reviewed-by: NShawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: NHarish Jenny K N <harish_kandiga@mentor.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Certain Micron eMMC v4.5 cards might get broken when HPI feature is used
and hence this patch disables the HPI feature for such buggy cards.

In U-Boot, these cards are reported as

Manufacturer: Micron (ID: 0xFE)
OEM: 0x4E
Name: MMC32G
Revision: 19 (0x13)
Serial: 959241022  Manufact. date: 8/2015 (0x82)  CRC: 0x00
Tran Speed: 52000000
Rd Block Len: 512
MMC version 4.5
High Capacity: Yes
Capacity: 29.1 GiB
Boot Partition Size: 16 MiB
Bus Width: 8-bit

According to JEDEC JEP106 manufacturer 0xFE is Numonyx, which was bought by
Micron.
Signed-off-by: NDirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: NMark Craske <Mark_Craske@mentor.com>
Cc: <stable@vger.kernel.org> # 4.8+
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

PARTITION_CONFIG is cached in mmc_card->ext_csd.part_config and the
currently active partition in mmc_blk_data->part_curr. These caches do
not always reflect changes if the ioctl call modifies the
PARTITION_CONFIG registers, e.g. by changing BOOT_PARTITION_ENABLE.

Write the PARTITION_CONFIG value extracted from the ioctl call to the
cache and update the currently active partition accordingly. This
ensures that the user space cannot change the values behind the
kernel's back. The next call to mmc_blk_part_switch() will operate on
the data set by the ioctl and reflect the changes appropriately.
Signed-off-by: NBastian Stender <bst@pengutronix.de>
Signed-off-by: NJan Luebbe <jlu@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Reuse existing functionality from memdup_user() instead of keeping
duplicate source code.

This issue was detected by using the Coccinelle software.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Variable err would be firstly initialized by the return value of
mmc_sd_switch().
Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Since we could move card->host->caps & MMC_CAP_4_BIT_DATA
ahead of mmc_sdio_init_uhs_card, in mmc_host_uhs(). So there
we could save this bit to check that. Also, if the process of
sdio_enable_4bit_bus goes wrong, we should bails out early.
Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Per SD specification physical layer v4.0, section 3.9.4, it
says "UHS-I supports only 4-bit mode. Host shall select 4-bit
mode by ACMD6. However mmc_sd_init_uhs_card() still go ahead
to initialize the cards anyway, whether card or host won't
support 4-bit mode.

  This breaks the platforms which could support UHS-I mode but on
some certain boards only support 1-bit mode with a UHS-I card inserted,
as all the tuning process is broken due to this. Alternatively, we
should check the return value from mmc_set_bus_width() to see if host
could finish the request to switch the bus width on its side. But that
needs more thing to do than this patch that just bails out early to try
high speed mode if 4-bit mode isn't available for whatever reason. And
this patch could also fix the same problem for sdio since R4_18V_PRESENT
won't be set for ocr when mmc_sdio_init_card() finds mmc_host_uhs()
is false.

  Note that this patch doesn't keep the checking of card->scr.sda_spec3
and comparing card->scr.bus_widths with SD_SCR_BUS_WIDTH_4 within
mmc_sd_init_uhs_card() since if the sd cards response with SD_ROCR_S18A,
it definitely supports UHS-I mode, which implicitly means these checkings
are always true.
Signed-off-by: NShawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This patch has been generated as follows:

for verb in set_unlocked clear_unlocked set clear; do
  replace-in-files queue_flag_${verb} blk_queue_flag_${verb%_unlocked} \
    $(git grep -lw queue_flag_${verb} drivers block/bsg*)
done

Except for protecting all queue flag changes with the queue lock
this patch does not change any functionality.

Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Shaohua Li <shli@fb.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Ming Lei <ming.lei@redhat.com>
Signed-off-by: NBart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Acked-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Commit 03dbaa04 ("mmc: slot-gpio: Add support to enable irq wake on
cd_irq") enabled wakeup at initialization. However, users also want to
control it from sysfs power/wakeup attribute. That means the driver needs
to check the PM flags before enabling it in the suspend callback. Add
support for that in sdhci-pci, which is the only driver presently using the
MMC_CAP_CD_WAKE flag, and remove the enabling in mmc_gpiod_request_cd_irq()
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Commit 03dbaa04 ("mmc: slot-gpio: Add support to enable irq wake on
cd_irq") enabled wakeup at initialization. However drivers may wish to
enable and disable based on different criteria. Add a helper function
mmc_gpio_set_cd_wake() to make it easy for drivers to do that.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: NAvri Altman <avri.altman@wdc.com>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Reviewed-by: NShawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

If the max_discard value is zero, the conditional branch that checks the
trim capabilities will never update this value with max_trim.

Change the condition statement to also check the max_discard value in order
to avoid an unnecessary call to mmc_do_calc_max_discard.
Signed-off-by: NSergio Valverde <vlvrdv@gmail.com>
Reviewed-by: NShawn Lin <shawn.lin@rock-chip.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

As the block layer, since the conversion to blkmq, claims the host using a
context, a following nested call to mmc_claim_host(), which isn't using a
context, may hang.

Calling mmc_interrupt_hpi() and mmc_read_bkops_status() via the mmc block
layer, may suffer from this problem, as these functions are calling
mmc_claim|release_host().

Let's fix the problem by removing the calls to mmc_claim|release_host()
from the above mentioned functions and instead make the callers responsible
of claiming/releasing the host. As a matter of fact, the existing callers
already deals with it.

Fixes: 81196976 ("mmc: block: Add blk-mq support")
Reported-by: NDmitry Osipenko <digetx@gmail.com>
Suggested-by: NAdrian Hunter <adrian.hunter@intel.com>
Tested-by: NDmitry Osipenko <digetx@gmail.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Reviewed-by: NShawn Lin <shawn.lin@rock-chips.com>

Like mmc_can_gpio_cd(), mmc_can_gpio_ro() will also be useful for host
drivers to know whether GPIO write-protect detection is supported.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

If the MMC_DRV_OP_GET_EXT_CSD request completes successfully, then
ext_csd must be freed, but in one case it was not. Fix that.
Signed-off-by: NLiu Changcheng <changcheng.liu@intel.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The Weibu F3C MiniPC has an onboard AP6255 module, presenting
two SDIO functions on a single MMC host (Bluetooth/btsdio and
WiFi/brcmfmac), and the mmc layer correctly detects this as
non-removable.

After suspend/resume, the wifi and bluetooth interfaces disappear
and do not get probed again.

The conditions here are:

 1. During suspend, we reach mmc_pm_notify()

 2. mmc_pm_notify() calls mmc_sdio_pre_suspend() to see if we can
    suspend the SDIO host. However, mmc_sdio_pre_suspend() returns
    -ENOSYS because btsdio_driver does not have a suspend method.

 3. mmc_pm_notify() proceeds to remove the card

 4. Upon resume, mmc_rescan() does nothing with this host, because of
    the rescan_entered check which aims to only scan a non-removable
    device a single time (i.e. during boot).

Fix the loss of functionality by detecting that we are unable to
suspend a non-removable host, so avoid the forced removal in that
case. The comment above this function already indicates that this
code was only intended for removable devices.
Signed-off-by: NDaniel Drake <drake@endlessm.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

To get an usdhc Apacer and some ATP SD cards work reliable, CMD23 needs
to be disabled.  This has been tested on i.MX6 (sdhci-esdhc) and rk3288
(dw_mmc-rockchip).

Without this patch on i.MX6 (sdhci-esdhc):

 $ dd if=/dev/urandom of=/mnt/test bs=1M count=10 conv=fsync

    | <mmc0: starting CMD23 arg 00000400 flags 00000015>
    | mmc0: starting CMD25 arg 00a71f00 flags 000000b5
    | mmc0:     blksz 512 blocks 1024 flags 00000100 tsac 3000 ms nsac 0
    | mmc0:     CMD12 arg 00000000 flags 0000049d
    | sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
    | mmc0: Timeout waiting for hardware interrupt.

Without this patch on rk3288 (dw_mmc-rockchip):

    | mmc1: Card stuck in programming state! mmcblk1 card_busy_detect
    | dwmmc_rockchip ff0c0000.dwmmc: Busy; trying anyway
    | mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz,
    | actual 400000HZ div = 0)
    | mmc1: card never left busy state
    | mmc1: tried to reset card, got error -110
    | blk_update_request: I/O error, dev mmcblk1, sector 139778
    | Buffer I/O error on dev mmcblk1p1, logical block 131586, lost async
    | page write
Signed-off-by: NChristoph Fritz <chf.fritz@googlemail.com>
Cc: <stable@vger.kernel.org> # v4.14+
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

mmc_blk_alloc_req() is supposed to return error pointers but there is
one path where we forget to set the error code and accidentally return
NULL.  The callers are not expecting that and will have a NULL pointer
dereference.

Fixes: 41e3efd0 ("mmc: block: Simplify cleaning up the queue")
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Remove code no longer needed after the switch to blk-mq.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Tested-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Remove code no longer needed after the switch to blk-mq.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Tested-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Remove config option MMC_MQ_DEFAULT and parameter mmc_use_blk_mq, so that
blk-mq must be used always.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Tested-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

mmc_test disables the command queue because none of the tests use the
command queue. However the Reset Test will re-enable it, so disable it in
that case too.

Fixes: 9d4579a8 ("mmc: mmc_test: Disable Command Queue while mmc_test is used")
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

mmc_test now uses mmc_start_request() to test sending commands during
"ongoing" asynchronous transfers, i.e. tests:
	Commands during non-blocking read - use Set Block Count (CMD23)
	Commands during non-blocking write - use Set Block Count (CMD23)

mmc_start_request() was not initializing cmd_completion, but cmd_completion
is used by "ongoing" transfers, so move initialization of cmd_completion
into making mmc_start_request().

Fixes: cb39f61e ("mmc: core: Export a few functions needed for blkmq support")
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Calling getnstimeofday() can suffer from time jumps and from the
y2038 overflow, so it is not appropriate here. Using ktime_get_ts64()
solves both problems. Using ktime_get() with ktime_t timestamps would
also work, but it seems that we mainly want to print the times as
seconds+nanoseconds, so it would require an extra division in the output.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>