Alive notification ver2 support error table information
for 2 CPUs.
This is useful to fetch the error information in case of
firmware assert.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The main complexity of the power code is that it needs to
take into account the firmware limitations.
These limitations state that we need to have a global
picture of the vifs present in the system to be able to
decide if we can enable power management on a specific vif.

Even device power save (as opposed to vif power management)
must be disabled in certain circumstances (monitor vif).

Refactor the current code to make this clearer by defining
a function that explicitely computes these constraints.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Its logic can be implemented with
iwl_mvm_power_mac_update_mode.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

If the driver detects old firmware, we disable support for
power management.
This greatly simplifies the code.
Reviewed-by: NAlexander Bondar <alexander.bondar@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Instead of re-building the power command upon debugfs read,
store the latest command sent to the firmware.
This reduces the code complexity by reducing the number of
entries in the power code.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Reviewed-by: NAlexander Bondar <alexander.bondar@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Reduce indentation where it is possible.
Make a function static - it wasn't used outside its file
anyway.
Remove the unneeded pm_prevent state.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Support taking an mvm ref (and preventing D0i3) by
writing '1' into the d0i3_refs debugfs file.

The reference can be unref by writing 0 to the same
file.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Schedule work to query the wakeup reasons, and
disconnect in some cases (e.g. beacon loss).
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

We don't want to go into D0i3, when P2P_CLI, AP (including
GO) or IBSS interfaces are running, so take appropriate
references.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Take a reference when ROC command is started, and
unref it on completion.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Take a reference when starting to scan and release it on completion.
Note that if the scan is cancelled/aborted, a completion will still be
sent up.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Hold a bitmap of taken references, according to the
reference reason (e.g. down, scan).

This will allow us validate our state and add some debugfs
entries later on.

Unref the transport when the FW is fully initialized,
allowing it to go into a low power mode.

Disallow the transition to low-power while recovery is in
progress.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Configure skip-over-dtim and beacon filtering on D0i3
enter/exit.

Since the D0i3 entry/exit commands require different
command flags (e.g. CMD_HIGH_PRIORITY), add a new parameter
to the functions being called, and make the current users
pass CMD_SYNC.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Reviewed-by: NAlexander Bondar <alexander.bondar@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The tx backoff settings used by the thermal throttling mechanism can
also be used for enforcing a limit on the power consumption of the module.

Handle the platform PCIe power limitation by translating the limit
(measured in mw) to its respective tx backoff value. The translation is
module specific.

The resulting tx backoff value is sent to the ucode, and also serves as the
minimal backoff value that can be set by the thermal throttling mechanism.
Signed-off-by: NIdo Yariv <idox.yariv@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This will be useful during tests done on the physical layer.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Allow reading and setting bcast filtering configuration
through debugfs.

By default, mvm->bcast_filters is used for setting
the bcast filtering configuration (these filters
will be configured for each associated station).

For testing purposes, allow overriding this configuration,
and setting the bcast filtering configuration manually.
The following debugfs keys can be used:
* bcast_filtering/override - use debugfs values instead
	of default configuration
* bcast_filtering/filters - set filters (+ attributes)
* bcast_filtering/macs - per-mac bcast filtering
	configuration (policy + attached filters)
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Broadcast filtering allows dropping broadcast
frames that don't match the configured patterns.

Use predefined filters, and configure them for
each associated station vif.

There is no need to optimize and attach the same
filter to multiple vifs, as a following patch
will configure each filter to have per-vif unique
values.

Configure the bcast filtering on assoc changes.

Add a new IWLWIFI_BCAST_FILTERING Kconfig option
in order to enable broadcast filtering.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

For various traffic use cases, we want to be able to treat multi-
channel scenarios differently. Introduce a low-latency framework
that currently only has a debugfs file to enable low-latency mode,
but can later be extended.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

We somtimes need to fetch the iwl_mvm_sta structure from a
station index - provide a helper to do that.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The identification of the hardware section in the NVM
of new devices has been changed, hence the need to add it
to iwl_cfg and adapt the code that uses this value
accordingly.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Happy new year!
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Currently, the MAC context tsf_id assignment and the master/slave
relations are determined only when a new vif is added, as part
of the MAC context resource allocation. However, at this stage, the
beacon interval is not known, and thus could not be taken into account
in the master-slave algorithm.

To fix this, recalculate the MAC context tsf_id assignment,
just before the MAC context is activated, i.e., just before
a station VMAC is configured to associated and before an AP
VMAC is started.
Signed-off-by: NIlan Peer <ilan.peer@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Instead of always calling ieee80211_beacon_loss() on every missed
beacons notification, call this function only if the number of
consecutive missed beacons from last rx is higher than a predefined
threshold.
Signed-off-by: NIlan Peer <ilan.peer@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The documentation for smps_requests is unclear, rewrite it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Configure the fw to filter multicast according to
the addresses given by mac80211.

Note that bssid should be given even if we want
to pass all the multicast frames.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When monitor interface is activated device power save needs
to be disabled.
Re-consider power management status on other active
interfaces when monitor interface is bound or unbound.
Signed-off-by: NAlexander Bondar <alexander.bondar@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

FW still does not support power management on multiple MAC interfaces.
Currently the driver enforce this limitation by disabling PM if second
interface is added. Change this behavior to allow PM on a single interface
even if other interfaces exist but not bound to any specific PHY.
PM will be enabled if only one single interface is bound.
Signed-off-by: NAlexander Bondar <alexander.bondar@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

FW implements protective algorithm to identify AP's improper uAPSD
behavior. FW sends misbehaving AP notification in this case.
Add this notification handling. Avoid using uAPSD in next association
to the exactly same AP. Refactor iwl_mvm_power_build_cmd() to move
uAPSD related code to a separate function.
Signed-off-by: NAlexander Bondar <alexander.bondar@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Send firmware a Smart FIFO Configuration host command to allow
interrupt coalescing. The smart FIFO is enabled when there is
only one bound interface (other than  p2p devices which are
ignored) and it is of type station, and activated while the
station is associated.

Smart Fifo allows aggragations of DMA transactions and by that
causes processor and memory controller to stay for a longer time
on lower c-states, thus saving platform power.
Firmware relies on driver to activate and disable it.
Signed-off-by: NLilach Edelstein <lilach.edelstein@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This allows to see the content of the NVM the driver reads.
Note that the output is in binary, and requires some
external user space tool to display the data properly.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

There's really no reason to use void *dbgfs_data
rather than a struct iwl_mvm *mvm, so do that.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Keeping connection can be useful also when testing d3
using the debugfs file (d3_test).

Save the vif to keep connection on, and consider it
when iterating over the interfaces.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Remove the flags parameter which should be set to sync or async
according to whether this is called during sta init or not.
Signed-off-by: NEyal Shapira <eyal@wizery.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Reported by "make includecheck"

Tested that the corresponding sources still compile well on x86
Signed-off-by: NMichael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

At the firmware level, IBSS support has similar programming
requirements as AP/GO support, so use the same functions with
just small differences.

With IBSS only a single virtual interface can be used, so no
changes in the advertised interface combinations are needed.

For now, don't use hardware crypto for the GTKs in IBSS mode,
the firmware should support it though.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Remove code that is not needed and always allow MIMO when
in tight mode. In loose mode, we should avoid MIMO since BT
can use the other antenna to Rx while we Tx.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

BT Coex needs to be updated when the bandwidth is modified
by the AP.
While at it, remove the vif parameter from
bt_coex_vif_change since it was unused.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Until now, after WoWLAN, we weren't able to keep the
connection to the AP because the firmware didn't give
us the right information. Since the firmware API has
been changed to include all the information we need,
change the driver to work with the new API (if it is
available) and program all the relevant information
in mac80211 to keep the connection.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Some NICs embedded in platforms that have only 16 Tx queues,
this affect the mapping of the Tx queues.
Signed-off-by: NEytan Lifshitz <eytan.lifshitz@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: NGregory Greenman <gregory.greenman@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Some NICs aren't allowed to be powered up at driver load time.
Fix it, and move the external NVM loading from driver load time to
driver up time (parsing the external nvm file remains at driver load time).
Signed-off-by: NEytan Lifshitz <eytan.lifshitz@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>