First round of fix for the endianess check warnings from make C=2 CF="-D__CHECK_ENDIAN__".
Signed-off-by: NMaggie <xmzhang@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Fix all sparse check warnings from make C=2.
Signed-off-by: NMaggie <xmzhang@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NEddie Wai <eddie.wai@broadcom.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NEddie Wai <eddie.wai@broadcom.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Various error conditions inside ep_connect and ep_disconnect were
either not being handled or not being handled correctly.  This patch
fixes all those issues.
Signed-off-by: NEddie Wai <eddie.wai@broadcom.com>
Acked-by: NAnil Veerabhadrappa <anilgv@broadcom.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Added the handling for cases when a chip request is made to the
CNIC module but the hardware is not ready to accept.  This would
lead to many unnecessary wait timeouts.
This code adds check in the connect establishment and destruction
path.
Signed-off-by: NEddie Wai <eddie.wai@broadcom.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The stop path has been augmented to wait a max of 10s for all in
progress offload and destroy activities to complete before proceeding
to terminate all active connections (via iscsid or forcefully).

Note that any new offload and destroy requests are now blocked and
return to the caller immediately.
Signed-off-by: NEddie Wai <eddie.wai@broadcom.com>
Acked-by: NAnil Veerabhadrappa <anilgv@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The code no longer needs to dynamically register and unregister
the CNIC device.  The CNIC device will be kept registered until
module unload.
Signed-off-by: NEddie Wai <eddie.wai@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Added net_dev mutex lock protection before accessing the csk
parameters.
Signed-off-by: NEddie Wai <eddie.wai@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

In the situation where the connect completion response arrives after
the connect request has already timed out, the connection was not being
aborted but only the resource was being freed.  This creates a problem
for 5771X (10g) as the chip flags this with an assertion.

This change will properly aborts the connection before freeing the
resource.
Signed-off-by: NEddie Wai <eddie.wai@broadcom.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Modified the handling of the remote TCP RST code so the chip can now
flush the tx pipe accordingly upon a remote TCP RST reception.
Signed-off-by: NEddie Wai <eddie.wai@broadcom.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

A cid leak issue was found when the connect destroy request exceeded
the driver's disconnection timeout.  This will lead to a cid resource
leak issue.
The fix is to allow the cid cleanup even when this happens.
Signed-off-by: NEddie Wai <eddie.wai@broadcom.com>
Acked-by: NAnil Veerabhadrappa <anilgv@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Added a be32_to_cpu call for the TMF LUN wqe.
Signed-off-by: NEddie Wai <eddie.wai@broadcom.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The patch fixes the following situations where NOP-Out pkt is called for:
- local unsolicited NOP-Out requests (requesting no NOP-In response)
- local NOP-Out responses to unsolicited NOP-In requests

kernel panic is observed due to double session spin_lock requests; one in the
bnx2i_process_nopin_local_cmpl routine in bnx2i_hwi.c and the other in the
iscsi_put_task routine in libiscsi.c

The proposed fix is to export the currently static __iscsi_put_task() routine
and have bnx2i call it directly instead of the iscsi_put_task() routine which
holds the session spin lock.
Signed-off-by: NEddie Wai <eddie.wai@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Reviewed-by: NAnil Veerabhadrappa <anilgv@broadcom.com>
Acked-by: NBenjamin Li <benli@broadcom.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Unsolicited NOP-Ins are placed in the receive queue of the hardware
which requires to be read out regardless if the receive pipe is suspended
or not.  This patch adds the disposal of this RQ element under this
condition.
Also fixed the bug in the unsolicited NOP-In handling routine which
checks for the RESERVED_ITT.
Signed-off-by: NEddie Wai <eddie.wai@broadcom.com>
Reviewed-by: NMichael Chan <mchan@broadcom.com>
Reviewed-by: NBenjamin Li <benli@broadcom.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NKashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Changing debug print to correct string.
Signed-off-by: NKashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Fix oops loading driver when there is direct attached
SEP device

The driver set max phys count to the value reported in sas iounit page
zero.  However this page doesn't take into account additional virutal
phys.  When sas topology event arrives, the phy count is larger than
expected, and the driver accesses memory array beyond the end of
allocated space, then oops.  Manufacturing page 8 contains the info
on direct attached phys.

For this fix will making sure that sas topology event is not
processing phys greater than the expected phy count.
Signed-off-by: NKashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

change_queue_depth callback API changed
The change_queue_depth callback changed where there is now an additional
parameter called reason, with SCSI_QDEPTH_DEFAULT, SCSI_QDEPTH_QFULL,
and SCSI_QDEPTH_RAMP_UP codes.
Signed-off-by: NKashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

remove support for MPI2_EVENT_TASK_SET_FULL
This event is obsoleted, so this processing of this event
needs to be removed from the driver.  The controller firmware is going
to handle TASK_SET_FULL, the driver doesn't need to do anything.
Even though we are removing the EVENT handling, the behavour has not
changed between driver versions becuase fimrware will still be handling
queue throttling, and retrying of commands when the target device queues
are full.
Signed-off-by: NKashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

MPI2 Rev header files.

1) Removed Task Set Full Event. Modified description of Disable SCSI
Initiator Task Set Full Handling bit in the Flags field of IO Unit
Page 1. Modified the descriptions for the three queue depth fields in
SAS IO Unit Page 1.
(2) Added new value for the Current Operation bits of the Flags field
in the RAID Volume Indicator Structure to indicate that the Make Data
Consistent operation is running.
(3) Added a value of 0x6 to various SAS link rate fields to indicate an
attached PHY that is not using any commonly supported settings.
(4) Added Volume Not Consistent bit to the VolumeStatusFlags field of
RAID Volume Page 0.
(5) Added a new value for the IncompatibleReason field of RAID Physical
Disk Page 0 to indicate an incompatible media type.
(6) Added Diagnostic Data Upload tool for the Toolbox Request.
Signed-off-by: NKashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Issue : Switch swap doesn't work when device missing delay is enabled.

(1) add support to individually add and remove phys to and from
existing ports. This replaces the routine
_transport_delete_duplicate_port.
(2) _scsih_sas_host_refresh - was modified to change the link rate
from zero to 1.5 GB rate when the firmware reports there is an
attached device with zero link.
(3) add new function mpt2sas_device_remove, this is wrapper function
deletes some redundant code through out driver by combining into one
subrountine
(4) two subroutines were modified so the sas_device, raid_device, and
port lists are traversed once when objects are deleted from the list.
Previously it was looping back each time an object was deleted from the
list.
Signed-off-by: NKashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Create a pool of chain buffers, instead of dedicated per IO:
This enahancment is to address memory allocation failure when asking
for more than 2300 IOs per host.   There is just not enough contiquious
DMA physical memory to make one single allocation to hold both message
frames and chain buffers when asking for more than 2300 request. In order
to address this problem we will have to allocate memory for each chain
buffer in a seperate individual memory allocation, placing each chain
element of 128 bytes onto a pool of available chains, which can be
shared amoung all request.
Signed-off-by: NKashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Ability to override/set the ReportDeviceMissingDelay and
IODeviceMissingDelay from driver: Add new command line option missing_delay,
this is an array, where the first element is the device missing delay,
and the second element is io missing delay.  The driver will program
sas iounit page 1 with the new setting when the driver loads. This is
programmed to the current and persistent configuration page so this takes
immediately, as will be sticky across host reboots.
Signed-off-by: NKashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Sometime it is seen that controller
firmware returns an invalid system message id (smid).

the oops is occurring becuase mpt_callbacks pointer is referenced to
either null or invalid virtual address.  this is due to cb_idx set
incorrectly from routine _base_get_cb_idx.  the cb_idx was set incorrectly
becuase there is no check to make sure smid is less than maxiumum
anticapted smid.   to fix this issue, we add a check in
_base_get_cb_idx to make sure smid is not greater than
ioc->hba_queue_depth.   in addition, a similar check was added to make
sure the reply address was less than the largest anticapated address.

Newer firmware has sovled this issue, however it good to have this sanity
check.
Signed-off-by: NKashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The compiler throws warning messages while compiling without
CONFIG_SCSI_MPT2SAS_LOGGING.
Set proper ifdef for CONFIG_SCSI_MPT2SAS_LOGGING to avoid warnnings.
Signed-off-by: NKashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Added support for ELS RRQ command

- Add new routine lpfc_set_rrq_active() to track XRI qualifier state.
- Add new module parameter lpfc_enable_rrq to control RRQ operation.
- Add logic to ELS RRQ completion handler and xri qualifier timeout
  to clear XRI qualifier state.
- Use OX_ID from XRI_ABORTED_CQE for RRQ payload.
- Tie abort and XRI_ABORTED_CQE andler to RRQ generation.
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Add SLI4 FC Discovery support

- Replace READ_LA and READ_LA64 with READ_TOPOLOGY mailbox command.
- Converted the old READ_LA structure to use bf_set/get instead of bit fields.
- Rename HBA_FCOE_SUPPORT flag to HBA_FCOE_MODE. Flag now indicates function
  is running as SLI-4 FC or FCoE port. Make sure flag reset each time
  READ_REV completed as it can dynamically change.
- Removed BDE union in the READ_TOPOLOGY mailbox command and added a define to
  define the ALPA MAP SIZE. Added FC Code for async events.
- Added code to support new 16G link speed.
- Define new set of values to keep track of valid user settable link speeds.
- Used new link speed definitions to define link speed max and bitmap.
- Redefined FDMI Port sppeds to be hax values and added the 16G value.
- Added new CQE trailer code for FC Events.
- Add lpfc_issue_init_vfi and lpfc_init_vfi_cmpl routines.
- Replace many calls to the initial_flogi routine with lpfc_issue_init_vfi.
- Add vp and vpi fields to the INIT_VFI mailbox command.
- Addapt lpfc_hba_init_link routine for SLI4 use.
- Use lpfc_hba_init_link call from lpfc_sli4_hba_setup.
- Add a check for FC mode to register the FCFI before init link.
- Convert lpfc_sli4_init_vpi to be called without a vpi (get it from vport).
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

- Add the Lancer FC and FCoE PCI IDs
- Add new SLI4 INTF register definitions
- Implement new SLI4 doorbell register
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Fix critical errors and crashes

- Replace LOF_SECURITY with LOG_SECURITY
- When calculating diag test memory size, use full size with header.
- Return LS_RJT with status=UNSUPPORTED on unrecognized ELS's
- Correct NULL pointer dereference when lpfc_create_vport_work_array()
  returns NULL.
- Added code to handle CVL when port is in LPFC_VPORT_FAILED state.
- In lpfc_do_scr_ns_plogi, check the nodelist for FDMI_DID and reuse
  the resource.
- Check for generic request 64 and calculate the sgl offset for the request
  and reply sgls, also calculate the xmit length using only the request bde.
Signed-off-by: NAlex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The current code in scsi_eh_target_reset() has an off by one error
that actually sends spurious extra resets.  Since there's no real need
to reset the targets in numerical order, simply chunk up the command
recovery list doing target resets and pulling matching targets out of
the list (that also makes the loop O(N) instead of O(N^2).

[mike christie found and fixed a list_splice -> list_splice_init problem]

Reported-by: Hillf Danton<dhillf@gmail.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The definition for the mailbox register for new adapters was incorrect.  The
value has been updated to the correct offset.

After an adapter reset, the mailbox register on the new adapters takes a
number of seconds to stabilize.  A delay has been added before reading the
register.
Signed-off-by: NWayne Boyer <wayneb@linux.vnet.ibm.com>
Acked-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The lun value was not getting set up correctly for all devices attached to the
new 64 bit adapters.  The fix is to move the logic to earlier in the
ipr_init_res_entry routine such that the value does get set correctly for all
devices.

Then the ipr_is_same_device comparison function was using the wrong lun value
in the logic for the new adapters.  Change this to use the correct lun value.
Signed-off-by: NWayne Boyer <wayneb@linux.vnet.ibm.com>
Acked-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Some kernel transport drivers unconditionally disable
retrieval of the Caching mode page. One such for example is
the BBB/CBI transport over USB.  Such a restraint is too
harsh as some devices do support the Caching mode
page. Unconditionally enabling the retrieval of this mode
page over those transports at their transport code level may
result in some devices failing and becoming unusable.

This patch implements a method of retrieving the Caching
mode page without unconditionally enabling it in the
transports which unconditionally disable it. The idea is to
ask for all supported pages, page code 0x3F, and then search
for the Caching mode page in the mode parameter data
returned. The sd driver already asks for all the mode pages
supported by the attached device by setting the page code to
0x3F in order to find out if the media is write protected by
reading the WP bit in the Device Specific Parameter
field. It then attempts to retrieve only the Caching mode
page by setting the page code to 8 and actually attempting
to retrieve it if and only if the transport allows it.

The method implemented here is that if the transport doesn't
allow retrieval of the Caching mode page and the device is
not RBC, then we ask for all pages supported by setting the
page code to 0x3F (similarly to how the WP bit is retrieved
above), and then we search for the Caching mode page in the
mode parameter data returned.

With this patch, devices over SATA, report this (no change):

Oct 22 18:45:58 localhost kernel: sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
Oct 22 18:45:58 localhost kernel: sd 0:0:0:0: Attached scsi generic sg0 type 0
Oct 22 18:45:58 localhost kernel: sd 0:0:0:0: [sda] Write Protect is off
Oct 22 18:45:58 localhost kernel: sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
Oct 22 18:45:58 localhost kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA

Smart devices report their Caching mode page. This is a
change where we'd previously see the kernel making
assumption about the device's cache being write-through:

Oct 22 18:45:58 localhost kernel: sd 6:0:0:0: Attached scsi generic sg2 type 0
Oct 22 18:45:58 localhost kernel: sd 6:0:0:0: [sdb] 610472646 4096-byte logical blocks: (2.50 TB/2.27 TiB)
Oct 22 18:45:58 localhost kernel: sd 6:0:0:0: [sdb] Write Protect is off
Oct 22 18:45:58 localhost kernel: sd 6:0:0:0: [sdb] Mode Sense: 47 00 10 08
Oct 22 18:45:58 localhost kernel: sd 6:0:0:0: [sdb] Write cache: enabled, read cache: enabled, supports DPO and FUA

And "dumb" devices over BBB, are correctly shown not to
support reporting the Caching mode page:

Oct 22 18:49:06 localhost kernel: sd 7:0:0:0: [sdc] 15663104 512-byte logical blocks: (8.01 GB/7.46 GiB)
Oct 22 18:49:06 localhost kernel: sd 7:0:0:0: [sdc] Write Protect is off
Oct 22 18:49:06 localhost kernel: sd 7:0:0:0: [sdc] Mode Sense: 23 00 00 00
Oct 22 18:49:06 localhost kernel: sd 7:0:0:0: [sdc] No Caching mode page present
Oct 22 18:49:06 localhost kernel: sd 7:0:0:0: [sdc] Assuming drive cache: write through
Signed-off-by: NLuben Tuikov <ltuikov@yahoo.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

To date libsas has only looked at the attached sas address when
determining the formation of wide ports.  The specification and some
hardware expects that phys with different addresses will not form a wide
port unless the local peer phys also match each other.  Introduce a flag
to select stricter behavior at sas_register_ha() time.  The flag can be
dropped once it is known that all libsas users expect the same behavior.

Current drivers just initialize this field to zero and get the
traditional behavior.
Reported-by: NPatrick Thomson <patrick.s.thomson@intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This patch (as1415) improves the formerly incomprehensible logic in
sd_media_changed() (the current code refers to "changed" as a state,
whereas in fact it is a relation between two states).  It also adds a
big comment so that everyone can understand what is really going on.

The patch also improves efficiency by not reporting a media change
when no medium was ever present.  If no medium was present the last
time we checked and there's still no medium, it's not necessary to
tell the caller that a change occurred.  Doing so merely causes the
caller to attempt to revalidate a non-existent disk, which is a waste
of time.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Rename log_level to bfa_log_level to make the global variable more bfa
specific and avoid clashes with other drivers which was causing a
build failure.
Signed-off-by: NJing Huang <huangj@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

PCI_DEVICE_ID_CISSF is defined as 323b in pci_ids.h but redefined as 3fff in
hpsa.c. The ID of 3fff will _never_ ship as a standalone controller. It is
intended only as part a complete storage solution. As such, this patch
removes the redefinition and the StorageWorks P1210m from the product table.

It also removes a duplicate line for the "unknown" controller support.
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>