Currently when performing a reboot with an ipr adapter,
the adapter gets shutdown completely, flushing all write
cache, as well as performing a full hardware reset of the card
during the shutdown phase of the old kernel. This ensures
the adapter is in a fully quiesced state across the reboot.

There are scenarios, however, such as when performing
kexec, where this full adapter shutdown is not required
and not desired, since it can make the reboot process take
noticeably longer.

This patch adds a module parameter to allow for skipping the
full shutdown during reboot. Rather than performing a full
adapter shutdown and reset, we simply cancel any outstanding
error buffers, place the adapter into a state where it has no
memory of any DMA addresses from the old kernel, then disable
the device. This significantly speeds up kexec boot, particularly
in configurations with multiple ipr adapters.
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Reviewed-by: NWen Xiong <wenxiong@linux.vnet.ibm.com>
Reviewed-by: NDaniel Kreling <kreling@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Set the tablesize based on the information given by the host.
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: NLong Li <longli@microsoft.com>
Tested-by: NLong Li <longli@microsoft.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

The current code assumes that the scatterlists presented are not chained.
Fix the code to not make this assumption.
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: NLong Li <longli@microsoft.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

We may exit this function without properly freeing up the maapings
we may have acquired. Fix the bug.
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: NLong Li <longli@microsoft.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

The storage protocol informs the guest of the I/O capabilities of the storage
stack. Retrieve this information and use it in the guest.
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: NLong Li <longli@microsoft.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

The current code always sent packets without data on the primary channel.
Properly distribute sending of packets with no data amongst all available
channels. I would like to thank Long Li for noticing this problem.
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: NLong Li <longli@microsoft.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Size the queue depth based on the ringbuffer size. Also accommodate for the
fact that we could have multiple channels (ringbuffers) per adaptor.
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: NLong Li <longli@microsoft.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Increase the default ring buffer size as this can significantly
improve performance especially on high latency storage back-ends.
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: NLong Li <longli@microsoft.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

This replaces kmalloc + memset by a call to kzalloc

This also fixes one checkpatch.pl issue in the process.

This improvement was suggested by "make coccicheck"
Signed-off-by: NMichael Opdenacker <michael.opdenacker@free-electrons.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

This effectively reverts commits 85b6c7 ("[SCSI] sd: fix cache flushing on
module removal (and individual device removal)" and dc4515ea ("scsi: always
increment reference count").

We now never call scsi_device_get from the shutdown path, and the fact
that we started grabbing reference there in commit 85b6c7 turned out
turned out to create more problems than it solves, and required
workarounds for workarounds for workarounds. Move back to properly checking
the device state and carefully handle module refcounting.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NPaolo Bonzini <pbonzini@redhat.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

The device model already takes care of races between ->remove and
->shutdown vs its other methods, and we now take care about locking
them out for ->rescan as well.

This is a partial revert of commit 39b7f1 ("[SCSI] sd: Fix refcounting").
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Lock the device embedded in the scsi_device to protect against
concurrent calls to ->remove.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Reviewed-by: NPaolo Bonzini <pbonzini@redhat.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Instances of var * HZ / 1000 are replaced by msecs_to_jiffies(var).
In addition some timing constants that assumed HZ 100 were adjusted
to HZ independent settings based on review comments from Michael Schmitz
<schmitzmic@gmail.com> and review of the original drivers in 1.0.31 and
2.2.16.
Signed-off-by: NNicholas Mc Guire <hofrat@osadl.org>
Acked-by: NMichael Schmitz <schmitzmic@gmail.com>
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

If CONFIG_SCSI_GENERIC_NCR5380=y:

drivers/scsi/g_NCR5380.c:727: warning: 'id_table' defined but not used

In the non-modular case, MODULE_DEVICE_TABLE() expands to nothing, and
id_table is not referenced.

Correct the existing #ifdef to fix this.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

This platform_driver does not need to set an owner, it will be populated by
the driver core.
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Signed-off-by: NFinn Thain <fthain@telegraphics.com.au>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Provide a file creation function that also takes an initial size so that the
caller doesn't have to set i_size, thus meaning that we don't have to call
deal with ->d_inode in the callers.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

With scsi-mq enabled, userspace programs can get unexpected EWOULDBLOCK
(a.k.a. EAGAIN) errors when submitting commands to the SCSI generic
driver.  Fix by calling blk_get_request() with GFP_KERNEL instead of
GFP_ATOMIC.

Note: to avoid introducing a potential deadlock, this patch should be
applied after the patch titled "sg: fix unkillable I/O wait deadlock
with scsi-mq".

Cc: <stable@vger.kernel.org> # 3.17+
Signed-off-by: NTony Battersby <tonyb@cybernetics.com>
Acked-by: NDouglas Gilbert <dgilbert@interlog.com>
Tested-by: NDouglas Gilbert <dgilbert@interlog.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

When using the write()/read() interface for submitting commands, the
SCSI generic driver does not call blk_put_request() on a completed SCSI
command until userspace calls read() to get the command completion.
Since scsi-mq uses a fixed number of preallocated requests, this makes
it possible for userspace to exhaust the entire preallocated supply of
requests.  For places in the kernel that call blk_get_request() with
GFP_KERNEL, this can cause the calling process to deadlock in a
permanent unkillable I/O wait in blk_get_request() -> ... -> bt_get().
For places in the kernel that call blk_get_request() with GFP_ATOMIC,
this can cause blk_get_request() always to return -EWOULDBLOCK.  Note
that these problems happen only if scsi-mq is enabled.  Prevent the
problems by calling blk_put_request() as soon as the SCSI command
completes instead of waiting for userspace to call read().

Cc: <stable@vger.kernel.org> # 3.17+
Signed-off-by: NTony Battersby <tonyb@cybernetics.com>
Acked-by: NDouglas Gilbert <dgilbert@interlog.com>
Tested-by: NDouglas Gilbert <dgilbert@interlog.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Fix SCSI generic read() incorrectly returning success after detecting an
error.

Cc: <stable@vger.kernel.org>
Signed-off-by: NTony Battersby <tonyb@cybernetics.com>
Acked-by: NDouglas Gilbert <dgilbert@interlog.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

wd719x_template is missing the .module field, causing module refcount
not to work, allowing to rmmod the driver while in use (mounted filesystem),
causing an oops.

Set .module to THIS_MODULE to fix the problem.
Signed-off-by: NOndrej Zary <linux@rainbow-software.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Correct compiler warning introduced by hpsa-add-local-workqueue patch
6636e7f4 hpsa: Use local workqueues
instead of system workqueues
Suggested-by: NKees Cook <keescook@chromium.org>
Reviewed-by: NScott Teel <scott.teel@pmcs.com>
Reviewed-by: NWebb Scales <webbnh@hp.com>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

fixed invalid assignment of 64bit mask to host dma_boundary for scatter gather segment boundary limit.

In reference to bug https://bugzilla.redhat.com/show_bug.cgi?id=1097141
Assert is seen with AMD cpu whenever calling pci_alloc_consistent.

[   29.406183] ------------[ cut here ]------------
[   29.410505] kernel BUG at lib/iommu-helper.c:13!
Signed-off-by: NMinh Tran <minh.tran@emulex.com>
Fixes: 6733b39a
Cc: <stable@vger.kernel.org>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

The patch "module: fix types of device tables aliases" newly requires that
invocations of

MODULE_DEVICE_TABLE(type, name);

come *after* the definition of `name'.  That is reasonable, but some
drivers weren't doing this.  Fix them.

Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Andrey Ryabinin <a.ryabinin@samsung.com>
Cc: David Miller <davem@davemloft.net>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: NMauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

printk and friends can now format bitmaps using '%*pb[l]'.  cpumask
and nodemask also provide cpumask_pr_args() and nodemask_pr_args()
respectively which can be used to generate the two printf arguments
necessary to format the specified cpu/nodemask.

* map_show()'s return value is too high by one and the function could
  modify beyond the end of the buffer when the formatted text is long
  enough.
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This allows those get_user_pages calls to pass FAULT_FLAG_ALLOW_RETRY to
the page fault in order to release the mmap_sem during the I/O.
Signed-off-by: NAndrea Arcangeli <aarcange@redhat.com>
Reviewed-by: NKirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andres Lagar-Cavilla <andreslc@google.com>
Cc: Peter Feiner <pfeiner@google.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

A shost_printk() statement was left over from debugging.
It can safely be removed; the same information is displayed
in the debugging message some lines further down.

Cc: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Make use of a new interface provided by iov_iter, backed by
scatter-gather list of iovec, instead of the old interface based on
sg_iovec. Also use iov_iter_advance() instead of manual iteration.

This commit should contain only literal replacements, without
functional changes.

Cc: Christoph Hellwig <hch@infradead.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Doug Gilbert <dgilbert@interlog.com>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Signed-off-by: NKent Overstreet <kmo@daterainc.com>
[dpark: add more description in commit message]
Signed-off-by: NDongsu Park <dongsu.park@profitbricks.com>
[hch: fixed to do a deep clone of the iov_iter, and to properly use
      the iov_iter direction]
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NMing Lei <tom.leiming@gmail.com>
Signed-off-by: NJens Axboe <axboe@fb.com>

This patch is to use firmware version macros from t4fw_version.h
and also enables 40g T5 adapter.
Signed-off-by: NPraveen Madhavan <praveenm@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

dev_printk() is now a void function, so the related functions
scmd_printk() and sdev_prefix_printk() should be made void, too.
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NHannes Reinecke <hare@suse.de>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Using seq_putc to print a single character saves at least a strlen()
call and a memory access, and may also give a small .text reduction.
Signed-off-by: NRasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: NFinn Thain <fthain@telegraphics.com.au>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Consecutive seq_puts calls with literal strings may be replaced by a
single call, saving a little .text.
Signed-off-by: NRasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: NFinn Thain <fthain@telegraphics.com.au>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Using seq_printf to print a simple string is a lot more expensive than
it needs to be, since seq_puts exists. Replace seq_printf with
seq_puts when possible.
Signed-off-by: NRasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: NFinn Thain <fthain@telegraphics.com.au>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Using seq_printf to print a simple string is a lot more expensive than
it needs to be, since seq_puts exists. Replace seq_printf with
seq_puts when possible.
Signed-off-by: NRasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: NFinn Thain <fthain@telegraphics.com.au>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Using seq_printf to print a simple string is a lot more expensive than
it needs to be, since seq_puts exists. Replace seq_printf with
seq_puts when possible.
Signed-off-by: NRasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: NFinn Thain <fthain@telegraphics.com.au>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

The macro SPRINTF doesn't save a lot of typing or make the code more
readable, and depending on a specific identifier (m) in the
surrounding scope is generally frowned upon. Nuke it.
Signed-off-by: NRasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: NFinn Thain <fthain@telegraphics.com.au>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

The 'data_dir' variable is not used in sg_common_write(), hence
remove this variable.
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Acked-by: NDouglas Gilbert <dgilbert@interlog.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Suggested-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NWebb Scales <webbnh@hp.com>
Reviewed-by: NKevin Barnett <Kevin.Barnett@pmcs.com>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Add in P840ar model name for gen9
Reviewed-by: NScott Teel <scott.teel@pmcs.com>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Add in gen9 controller model names
Reviewed-by: NScott Teel <scott.teel@pmcs.com>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Detect failues when attempting to change controller to use simple
or performant transport modes (mode change ack) rather than just
proceeding ahead after timeouts.

Return values are added to:
	hpsa_put_ctlr_into_performant_mode
	hpsa_wait_for_mode_change_ack
and all their callers check/propagate the result.

More consistency in printing errors and whether
dev_err is used.
Reviewed-by: NScott Teel <scott.teel@pmcs.com>
Signed-off-by: NRobert Elliott <elliott@hp.com>
Signed-off-by: NDon Brace <don.brace@pmcs.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>