Full duplex SPI operation should not read a dummy byte at the first transfer.
Bug and fix by Jean-Christian de Rivaz <jc@eclis.ch>:

http://blackfin.uclinux.org/gf/project/uclinux-dist/tracker/?action=TrackerItemEdit&tracker_item_id=3678Signed-off-by: NJean-Christian de Rivaz <jc@eclis.ch>
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

PBX 2 SPI devices need the nonstandard "cs change per word" mechanism.

This patch is one of three updating this driver to make the last data bits get
sent before advancing the transfer ...  in this case, before the chipselect
gets deactivated.
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use the SPI driver's name when requesting gpio lines.  When there are gpio
conflicts, this helps to narrow down the problems; "bfin-spi" is not
informative.
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove useless return status check in restore_state function.  Issue was
pointed out by Michael.

Cc: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This adds driver OMAP SPI specific changes to support OMAP 3430
Signed-off-by: NGirish S G <girishsg@ti.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add support for SPI over SCI pins.  SCI is a very simple serial controller
block that can be found on older SuperH processors.  In theory it is
possible to use the SCI hardware block in syncronous mode, but this version
of the driver simply hooks up the bit banging code on the SCI pins.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The two S3C SPI master drivers got merged without much review, so I just
noticed that they're doing something that the SPI core code is responsible
for, rather than any adapter driver: they try to register SPI devices.

This removes that support from those drivers so they act normally.
Interestingly, none of the current boards are affected.  So it's a net code
shrink with no loss of functionality.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In atmel_spi_next_xfer, xfer can be NULL because the next transfer may
already have been submitted to the PDC (using DMA chaining).  This can
cause an oops, since the debug message assumed it was never null.  The
fix changes how those debug messages are issued, ensuring that one is
issued each time a transfer is started instead of once per call.

Also, properly indent the "can this transfer be chained" test so it's
not hidden as if it were non-conditional code.
Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add support for chained transfers in the atmel_spi driver, letting the DMA
controller switch to the next buffer pair without CPU intervention.  This
reduced I/O latencies by about 2% in one bulk I/O test.  It should also help
work around several interrelated errata affecting chipselect 0 on at91rm9200
chips.

Almost all of the changes are in the reworked atmel_spi_next_xfer() function.
That's now called with the driver in one of three states:

 1. It isn't transferring anything (in which case the first transfer
    of the current message is going to be sent)
 2. It has finished transfering a non-chainable transfer (in which
    case it will go to the next transfer in the message)
 3. It has finished transfering a chained transfer (in which case the
    next transfer is already queued)

After that it will queue the next transfer if it can be chained.
Signed-off-by: NSzilveszter Ordog <slipszi@gmail.com>
Acked-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Don't insert (undesirable) delays between consecutive words (DLYBCT) or when
activating chipselects (DLYBS).

Removing the between-word delays improves the performance of bulk transfers
(such as mtd_dataflash, m25p80, mmc_spi) significantly.  In one test, the
improvement was a factor of more than eight!

(The large DLYBCT value came from the legacy at91 SPI driver, and it's not
clear why it used such a huge value.)
Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Don't update dev->power.power_state any more in the SPI core.  The only
reason to update this scheduled-to-be-removed field was to make the
already-removed /sys/devices/.../power/state files work better.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit edfaa7c3

    Driver core: convert block from raw kobjects to core devices

    This moves the block devices to /sys/class/block. It will create a
    flat list of all block devices, with the disks and partitions in one
    directory. For compatibility /sys/block is created and contains symlinks
    to the disks.

introduced a global disk_type variable in <linux/genhd.h>, causing the
following compile error on Atari:

    drivers/block/ataflop.c:93: error: conflicting types for 'disk_type'
    include/linux/genhd.h:21: error: previous declaration of 'disk_type' was here

Rename the local disk_type variable in drivers/block/ataflop.c to
atari_disk_type, to avoid the conflict.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Standardize the temperature units to millidegrees C for the two sensor
conversion routines.  Previously the routines were,

w1_DS18B20_convert_temp degrees C
w1_DS18S20_convert_temp millidegrees C

Unfortunately this will break any program using the ds18b20 value as it
will now be 1000 times bigger.  Fortunately there can't be that many users
out there, or some of these bugs will have been fixed by now, such as the
negative C error (see previous patch) that makes me think the ds18b20 is
the better choice to change because of the current bugs.
Signed-off-by: NDavid Fries <david@fries.net>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Simplify logic in cdrom_release() without semantic change.
Signed-off-by: NBorislav Petkov <bbpetkov@yahoo.de>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remvoe variable which actually is not used (except assigning it a value)
and confusing break out of the family checking loop.  Found by Harry Mason.
Signed-off-by: NEvgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Harry J Mason <hjm03r@ecs.soton.ac.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix section mismatch by making the driver template variable name
match one of the whitelisted variable names in modpost.

WARNING: vmlinux.o(.data+0x7a9e8): Section mismatch: reference to .init.text:tpm_inf_pnp_probe (between 'tpm_inf_pnp' and 'cn_idx')
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Cc: Marcel Selhorst <tpm@selhorst.net>
Acked-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Avoid calling do_div(x, 1) in this case.

Cc: David Fries <david@fries.net>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The kernel has a divide by zero crash when trying to run the system timer
less than 100Hz.  The problem is x/(HZ/USER_HZ) and related.  Now
x*(USER_HZ/HZ) will be used if HZ<USER_HZ.

I'm running the Linux kernel under qemu and went to run a slower system
timer to take less CPU (and battery) on the host.  I found that the kernel
paniced under emulation because of a divide by zero in three places.  Here
is the patch.  The base git was updated today 01-05-2008.  I went for a
20Hz system time by adding config HZ_20 etc to kernel/Kconfig.hz.  With
this patch I verified the system timer by looking at /proc/interrupts.

[akpm@linux-foundation.org: partially clean up the macro maze]
Signed-off-by: NDavid Fries <david@fries.net>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Specify also sub pci ids to not grab devices with properly set sub ids.
This devices has these set (unset) to the same as (plx 9050) ids.
Signed-off-by: NJiri Slaby <jirislaby@gmail.com>
Cc: Andreas Block <andreas.block@esd-electronics.com>
Cc: Oliver Thimm <oliver.thimm@esd-electronics.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

I have been prime author and maintainer of block2mtd from day one, but
neither MAINTAINERS nor the module source makes this fact clear.  And while
I'm at it, update my email addresses tree-wide, as the old address
currently bounces and change my name to "joern" as unicode will likely
continue to cause trouble until the end of this century.
Signed-off-by: NJoern Engel <joern@lazybastard.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Here's a couple of small additions to BUG-HUNTING.

1. point out that you can list code in gdb with only one command
	(gdb) l *(<symbol> + offset)

2. give a very brief hint how to decode module symbols in call traces
Signed-off-by: NRichard Kennedy <richard@rsk.demon.co.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

schedule_timeout(jiffies) waits for at least jiffies - 1.  Add 1 jiffie to
the timeout_jiffies calculated in sys_poll() to wait at least
timeout_msecs, like poll() manpage says.
Signed-off-by: NKarsten Wiese <fzu@wemgehoertderstaat.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix two N_TTY line discipline issues related to resuming a stopped TTY
(typically done with ctrl-S):

1) Fix handling of character that resumes a stopped TTY (with IXANY)

With "stty ixany", the TTY line discipline would lose the first character
after the stop, so typing, for example, "hi^Sthere" resulted in "hihere"
(the 't' would cause the resume after ^S, but it would then be thrown away
rather than processed as an input character).  This was inconsistent with
the behavior of other Unix systems.

2) Fix interrupt signal (e.g. ctrl-C) behavior in stopped TTYs

With "stty -ixany" (often the default), interrupt signals were ignored
in a stopped TTY until the TTY was resumed with the start char (typically
ctrl-Q), which was inconsistent with the behavior of other Unix systems.
Signed-off-by: NJoe Peterson <joe@skyrush.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Just converting this documentation semaphore reference, since we don't
want to promote semaphore usage.
Signed-off-by: NDaniel Walker <dwalker@mvista.com>
Acked-by: NCorey Minyard <minyard@acm.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

We can use ilog2() in fs/namespace.c to compute hash_bits and hash_mask at
compile time, not runtime.

[akpm@linux-foundation.org: clean it all up]
Signed-off-by: NEric Dumazet <dada1@cosmosbay.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

- Account for debug_smp_processor_id()'s own preempt_disable() when
  displaying the preempt_count().

- 80 cols, not 800.

Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

groups_sort() can be quite long if user loads a large gid table.

This is because GROUP_AT(group_info, some_integer) uses an integer divide.
So having to do XXX thousand divides during one syscall can lead to very
high latencies.  (NGROUPS_MAX=65536)

In the past (25 Mar 2006), an analog problem was found in groups_search()
(commit d74beb9f ) and at that time I
changed some variables to unsigned int.

I believe that a more generic fix is to make sure NGROUPS_PER_BLOCK is
unsigned.
Signed-off-by: NEric Dumazet <dada1@cosmosbay.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix the following section mismatch with CONFIG_HOTPLUG=n,
CONFIG_HOTPLUG_CPU=y:

WARNING: vmlinux.o(.text+0x399a6): Section mismatch: reference to .init.text.5:idle_regs (between 'fork_idle' and 'get_task_mm')
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

calibrate_delay() must be __cpuinit, not __{dev,}init.

I've verified that this is correct for all users.

While doing the latter, I also did the following cleanups:
- remove pointless additional prototypes in C files
- ensure all users #include <linux/delay.h>

This fixes the following section mismatches with CONFIG_HOTPLUG=n,
CONFIG_HOTPLUG_CPU=y:

WARNING: vmlinux.o(.text+0x1128d): Section mismatch: reference to .init.text.1:calibrate_delay (between 'check_cx686_slop' and 'set_cx86_reorder')
WARNING: vmlinux.o(.text+0x25102): Section mismatch: reference to .init.text.1:calibrate_delay (between 'smp_callin' and 'cpu_coregroup_map')
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Christian Zankel <chris@zankel.net>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fixing:
  CHECK   kernel/params.c
kernel/params.c:329:41: warning: incorrect type in argument 8 (different signedness)
kernel/params.c:329:41:    expected int *num
kernel/params.c:329:41:    got unsigned int *
Signed-off-by: NRichard Knutsson <ricknu-0@student.ltu.se>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Actual code let compiler generates idiv instruction on x86.

Using a right shift is OK here and readable as well.

Before patch
   10:   57                      push   %edi
   11:   56                      push   %esi
   12:   89 d6                   mov    %edx,%esi
   14:   53                      push   %ebx
   15:   89 c3                   mov    %eax,%ebx
   17:   eb 22                   jmp    3b <search_extable+0x2b>
   19:   89 f0                   mov    %esi,%eax
   1b:   ba 02 00 00 00          mov    $0x2,%edx
   20:   29 d8                   sub    %ebx,%eax
   22:   89 d7                   mov    %edx,%edi
   24:   c1 f8 03                sar    $0x3,%eax
   27:   99                      cltd
   28:   f7 ff                   idiv   %edi
   2a:   8d 04 c3                lea    (%ebx,%eax,8),%eax
   2d:   39 08                   cmp    %ecx,(%eax)
...

After patch

00000010 <search_extable>:
   10:   53                      push   %ebx
   11:   89 c3                   mov    %eax,%ebx
   13:   eb 18                   jmp    2d <search_extable+0x1d>
   15:   89 d0                   mov    %edx,%eax
   17:   29 d8                   sub    %ebx,%eax
   19:   c1 f8 04                sar    $0x4,%eax
   1c:   8d 04 c3                lea    (%ebx,%eax,8),%eax
   1f:   39 08                   cmp    %ecx,(%eax)
...
Signed-off-by: NEric Dumazet <dada1@cosmosbay.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add detection for IT87XX SuperIO chip and disabling its POST feature, which
made noise on parallel port's pins.
Signed-off-by: NPetr Cvek <petr.cvek@tul.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add the Dell UK 6400 Inspiron model (MM061) to allow the i8k module to load
correctly without using 'force=1'
Signed-off-by: N"Nick Warne" <nick@ukfsn.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use DEFAULT_SGI_PARTITION for SGI_PARTION default
Signed-off-by: NThomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix wrong netmos 9855 serial port configuration.

On loading only one serial port was present and it wasn't working.  After
looking in the data sheet I realized that the base address was wrong.  For
further reference here is lspci and relevant dmesg output:

02:00.0 Communication controller: NetMos Technology PCI 9855 Multi-I/O
Controller (rev 01) (prog-if 02)
        Subsystem: LSI Logic / Symbios Logic Unknown device 0022
        Flags: medium devsel, IRQ 19
        I/O ports at df00 [size=8]
        I/O ports at de00 [size=8]
        I/O ports at dd00 [size=8]
        I/O ports at dc00 [size=8]
        I/O ports at db00 [size=8]
        I/O ports at da00 [size=16]

parport1: PC-style at 0xdd00 [PCSPP,TRISTATE]
parport2: PC-style at 0xdf00 [PCSPP,TRISTATE,EPP]
0000:02:00.0: ttyS0 at I/O 0xdb00 (irq = 19) is a 16550A
0000:02:00.0: ttyS1 at I/O 0xda00 (irq = 19) is a 16550A
Signed-off-by: NChristian Pellegrin <chripell@fsfe.org>
Cc: Thomas Richter <thor@math.TU-Berlin.DE>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Martin Schitter <ms@gewi.kfunigraz.ac.at>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Added pci device id for the Quatech SPPXP-100 ExpressCard - 0x278 - to
include/linux/pci_id.h

Modified drivers/parport/parport_pc.c to support the Quatech SPPXP-100 Parallel port PCI ExpressCard

[akpm@linux-foundation.org: build fix]
Signed-off-by: NLuís P Mendes <luis.p.mendes@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

ext2 should not worry about checking sb->s_blocksize for XIP before the
sb's blocksize actually gets set.
Signed-off-by: NNick Piggin <npiggin@suse.de>
Acked-by: NCarsten Otte <cotte@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The port_write_mutex was converted from a semaphore to a mutex,
but there was still this ifdef'd init_MUTEX reference remaining.
Signed-off-by: NDaniel Walker <dwalker@mvista.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

[akpm@linux-foundation.org: cleanup]
Signed-off-by: NDaniel Walker <dwalker@mvista.com>
Acked-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NDenis Cheng <crquan@gmail.com>
Cc: Chris Mason <chris.mason@oracle.com>
Cc: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>