Add support for S3C6400 SDHCI channels 0 and 1, making
the GPIO code common to both S3C6400 and S3C6410.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add detection support for the S3C6400 SoC which has it's
id register in a different place to the S3C6410.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add the core support files for the Samsung S3C6400 SoC.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add minimial support for the SMDK6400 board to test
the S3C6400 support.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add power management support to the VIC by registering
each VIC as a system device to get suspend/resume
events going.

Since the VIC registeration is done early, we need to
record the VICs in a static array which is used to add
the system devices later once the initcalls are run. This
means there is now a configuration value for the number
of VICs in the system.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Move the GPIO suspend/resume support inline with the gpiolib support
so that it will work with both the S3C24XX and S3C64XX series.

The s3c_gpio_chip is extended to have a pm callback and a save block
to keep the state of the GPIO over suspend, and the code from the
s3c24xx implementation is added to a new common file.

The suspend process now uses the list of registered chips to go through
saving and restoring each one as appropriate, using the pm callback to
select the appropriate routine depending on the type of control register
present.

This change also means that any additional GPIO added should not require
changes to the PM.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add support for saving the state of the IRQ registers over suspend.

This requires moving the S3C64XX UART registers into <plat/regs-serial.h>
and adding irq-pm.c which saves the state of all the IRQ registers.

The irq-pm.c saves all the IRQ registers, including the IRQ_EINT and
IRQ_EINT_GROUP registers as it was easier than adding three different
files. Also ensuring that all the registers are restored to the same
state as before suspend is considered to be the best thing to do.

Note, we do not suspend the VIC here, this is done by the VIC driver
itself.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add an s3c64xx_sysclass and device for items that currently
want to bind to any s3c64xx processor. The first user of this
will be parts of the s3c64xx suspend support which need to
save device state over suspend/resume.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add definition for s3c6410_sysclass which was missing
from arch/arm/plat-s3c/include/plat/cpu.h.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add the initial support for the S3C64XX based systems to use
suspend-to-RAM to sleep.

Includes basic debugging for use with the SMDK6410 usign the
LEDs on the baseboard.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add the facility to save the UART UDIVSLOT register if the UART
state is being saved over suspend.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add a simple debug message on saving the UART state and add a per-arch
pre-restore function to be used by the s3c64xx restore code to ensure
the UARTs control registers do not go through any illegal state changes.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add USB OHCI host definitions.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

The USB host base address is available on both the S3C24XX and S3C64XX
ranges.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add USB OHCI host capability to the SMDK6410 for either USB OtG or
a single/double USB host port.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add common definition for USB OHCI platform device, add a Kconfig
to selectively compile it and add update all the users.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

arm is placing some code in the .text.init section, but it does not
reference that section in its linker scripts.

This change moves this code from the .text.init section to the
.init.text section, which is presumably where it belongs.
Signed-off-by: NTim Abbott <tabbott@mit.edu>
Acked-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Symbols like SOFT_RESET are way too generic to be exported at large.
To avoid this, let's move the mbus bridge register defines into a
separate file and include it where needed.  This affects mach-kirkwood,
mach-loki, mach-mv78xx0 and mach-orion5x simultaneously as they all
share code in plat-orion which relies on those defines.

Some other defines have been moved to narrower scopes, or simply deleted
when they had no user.

This fixes compilation problem with mpt2sas on the above listed
platforms.
Signed-off-by: NNicolas Pitre <nico@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Pass clocksource pointer to the read() callback for clocksources.  This
allows us to share the callback between multiple instances.

[hugh@veritas.com: fix powerpc build of clocksource pass clocksource mods]
[akpm@linux-foundation.org: cleanup]
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Acked-by: NJohn Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NHugh Dickins <hugh@veritas.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This is a version incorporating Christoph's suggestion.

Separate out common *fstatat functionality into a single function
instead of duplicating it all over the code.
Signed-off-by: NOleg Drokin <green@linuxhacker.ru>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

From: David Brownell <dbrownell@users.sourceforge.net>

Fix GPIO-related build error on mach-imx platform:

  CC      drivers/spi/spi_gpio.o
In file included from /home/db/kernel/scratch/arch/arm/include/asm/gpio.h:5,
                 from include/linux/gpio.h:7,
                 from drivers/spi/spi_gpio.c:23:
arch/arm/mach-imx/include/mach/gpio.h: In function 'imx_gpio_get_value':
arch/arm/mach-imx/include/mach/gpio.h:27: error: implicit declaration of function '__REG2'
arch/arm/mach-imx/include/mach/gpio.h:27: error: 'IMX_IO_BASE' undeclared (first use in this function)
arch/arm/mach-imx/include/mach/gpio.h:27: error: (Each undeclared identifier is reported only once
arch/arm/mach-imx/include/mach/gpio.h:27: error: for each function it appears in.)
arch/arm/mach-imx/include/mach/gpio.h: In function 'imx_gpio_set_value_inline':
arch/arm/mach-imx/include/mach/gpio.h:36: error: 'IMX_IO_BASE' undeclared (first use in this function)
arch/arm/mach-imx/include/mach/gpio.h:36: error: lvalue required as left operand of assignment
arch/arm/mach-imx/include/mach/gpio.h:38: error: lvalue required as left operand of assignment
	...
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Kernel 2.6.30-rc1 added sys_preadv and sys_pwritev to most archs
but not ARM, resulting in

<stdin>:1421:2: warning: #warning syscall preadv not implemented
<stdin>:1425:2: warning: #warning syscall pwritev not implemented

This patch adds sys_preadv and sys_pwritev to ARM.

These syscalls simply take five long-sized parameters, so they
should have no calling-convention/ABI issues in the kernel.

Tested on armv5tel eabi using a preadv/pwritev test program posted
on linuxppc-dev earlier this month.

It would be nice to get this into the kernel before 2.6.30 final,
so that glibc's kernel version feature test for these syscalls
doesn't have to special-case ARM.
Signed-off-by: NMikael Pettersson <mikpe@it.uu.se>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

As a result of an off-by-1 error pcm990 leaves one unused GPIO number between
built-in GPIOs and the pca9536 extender. Fix it.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Firstly, this patch makes the palm27x asoc driver a little more sane. Also,
since all affected devices use GPIO95 as AC97_nRESET, this patch sets that
properly. Affected are PalmT5, TX and LifeDrive.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Check pending queue and remove the adc client being released.
Signed-off-by: NRamax Lo <ramaxlo@gmail.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

The symbol 's3c_adc_try' in arch/arm/plat-s3c24xx/adc.c
does not need to be exported and thus should be static.

This fixes the following sparse warning:

adc.c:103:6: warning: symbol 's3c_adc_try' was not declared. Should it be static?
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

The .init_machine entry in mach-osiris.c had the same entry
twice, so remove one definition to fix the following warning
from sparse:

mach-osiris.c:416:3: warning: Initializer entry defined twice
mach-osiris.c:418:3:   also defined here
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Make 'anubis_ide_platdata' statis as it is not used outside
the file it is in, fixing the following sparse warning:

mach-anubis.c:246:27: warning: symbol 'anubis_ide_platdata' was not declared. Should it be static?
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Make 'jive_vgg2432a4_display' and 'jive_lcd_config' static as
they are not exported, and are generating the following sparse
warnings:

mach-jive.c:280:26: warning: symbol 'jive_vgg2432a4_display' was not declared. Should it be static?
mach-jive.c:313:28: warning: symbol 'jive_lcd_config' was not declared. Should it be static?
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Fix the following sparse warning due to s3c_device_hwmon being
missing from <plat/devs.h>

devs.c:380:24: warning: symbol 's3c_device_hwmon' was not declared. Should it be static?
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Fix the following sparse error generated by including
<plat/gpio-core.h> instead of <mach/gpio-core.h>

gpiolib.c:78:22: warning: symbol 's3c24xx_gpios' was not declared. Should it be static?
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

The VIC code will attempt to perform som
default set_irq_chip() and set_irq_chip_data()
on all IRQs supported by the VIC, while the new
IRQ handling code strictly checks for the global
NR_IRQS to be respected also for these IRQs.

This patch will respect the interrupt mask passed
to the VIC driver and will prevent it from
attempting to call these functions on any unused
interrupts.
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch removes several i.MX board specific defconfig files in favour
for a mx1_defconfig, mx27_defconfig and mx3_defconfig. All config files
have all currently available boards, i.MX specific drivers and the network
device drivers for the boards enabled.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This allows the regulator API to power off unused regulators at the end
of init.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Otherwise we'd need massive ifdefs in the code.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Move ifdef under function brackets. This fixes compile crach when IRQ priorities
are disabled.
Signed-off-by: NDarius Augulis <augulis.darius@gmail.com>

Signed-off-by: NDarius Augulis <augulis.darius@gmail.com>

AIPS[12] are no mapped from generic MX3 code so we don't need to
map them from machine-specific map_io function anymore.
Signed-off-by: NIlya Yanok <yanok@emcraft.com>

To match the mxc_iomux_setup_multiple_pins() prototype.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NPaulius Zaleckas <paulius.zaleckas@teltonika.lt>
Cc: Sascha Hauer <s.hauer@pengutronix.de>