The CIE and FDE structs are big enough and accessed regularly enough in
certain configurations to make cacheline alignment useful.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Conflicts:
	arch/sh/kernel/cpu/sh3/entry.S

sh64 does not yet support GENERIC_BUG, but still wants unwinder support.
Alias UNWINDER_BUG and UNWINDER_BUG_ON to their BUG counterparts until
the conversion to GENERIC_BUG is completed.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This simplifies the unwinder trap handling, dropping the use of the
special trapa vector and simply piggybacking on top of the BUG support. A
new BUGFLAG_UNWINDER is added for flagging the unwinder fault, before
continuing on with regular BUG dispatch.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

If the oprofile code is built as a module, unwind_stack() as used by the
oprofile backtrace code is not available, causing build breakage.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Allow a DWARF register to have an undefined value. When applied to the
DWARF return address register this lets lets us label a function as
having no direct caller, e.g. kernel_thread_helper().
Signed-off-by: NMatt Fleming <matt@console-pimps.org>

The 'end' member of struct dwarf_fde denotes one byte past the end of
the CFA instruction stream for an FDE. The value of 'end' was being
calcualted incorrectly, it was being set too high. This resulted in
dwarf_cfa_execute_insns() interpreting data past the end of valid
instructions, thus causing all sorts of weird crashes.
Signed-off-by: NMatt Fleming <matt@console-pimps.org>

When CONFIG_DWARF_UNWINDER is enabled setup r14 in handle_interrupt, so
that we can figure out what function was running when we were
interrupted.
Signed-off-by: NMatt Fleming <matt@console-pimps.org>

We can't assume that if we execute the unwinder code and the unwinder
was already running that it has faulted. Clearly two kernel threads can
invoke the unwinder at the same time and may be running simultaneously.

The previous approach used BUG() and BUG_ON() in the unwinder code to
detect whether the unwinder was incapable of unwinding the stack, and
that the next available unwinder should be used instead. A better
approach is to explicitly invoke a trap handler to switch unwinders when
the current unwinder cannot continue.
Signed-off-by: NMatt Fleming <matt@console-pimps.org>

The handling of DW_CFA_val_offset ops was incorrectly using the
DWARF_REG_OFFSET flag but the register's value cannot be calculated
using the DWARF_REG_OFFSET method. Create a new flag to indicate that a
different method must be used to calculate the register's value even
though there is no implementation for DWARF_VAL_OFFSET yet; it's mainly
just a place holder.
Signed-off-by: NMatt Fleming <matt@console-pimps.org>

Plug a memory leak in dwarf_unwinder_dump() where we didn't free the
memory that we had previously allocated for the DWARF frames and DWARF
registers.

Now is also a opportune time to implement our own mempool and kmem
cache. It's a good idea to have a certain number of frame and register
objects in reserve at all times, so that we are guaranteed to have our
allocation satisfied even when memory is scarce. Since we have pools to
allocate from we can implement the registers for each frame as a linked
list as opposed to a sparsely populated array. Whilst it's true that the
lookup time for a linked list is larger than for arrays, there's only
usually a maximum of 8 registers per frame. So the overhead isn't that
much of a concern.
Signed-off-by: NMatt Fleming <matt@console-pimps.org>

Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

fix the problem that MSC Tests of USBCV detects some warnings.
Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Update the kfr2r09 defconfig with support for LCDC and USB gadget.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add romImage defconfig for the kfr2r09 board. This defconfig
should be used to build the kernel based boot loader.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add a P1 jump to the the kfr2r09 romimage code. With this
patch applied the initial zImage assembly code will run
with instruction cache enabled.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add instruction cache and TLB invalidation code for the
the kfr2r09 romimage target.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Fix the kfr2r09 board code so it compiles if CONFIG_I2C=n.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This is the only board that presently supports this rtc, so make sure it
is enabled by default to get some build coverage.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

There were a few stray unused variables left over, kill them off.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

As an excellent indicator of how much testing the DSP code gets, a couple
of rather glaring bugs in the DSP save/restore paths were found:

- In the DSP restore case a0 needs to be popped off before a0g,
  or the value of a0g is clobbered by the MSB of a0 in the case
  of sign extension.

- Beyond that, the save and restore orders were out of sync,
  so this fixes that up as well. At the same time, we switch over
  to using movs.l for both the save and restore of the general DSP
  registers as opposed to using sts.l (which was initially put in
  place to work around a bug in ancient binutils versions which
  the kernel no longer supports).
Reported-by: NChee Soon Yip <yip.cheesoon@renesas.com>
Cc: Chu Lih Kwek <kwek.chulih@renesas.com>,
Cc: General Lai <general.lai@renesas.com>,
Cc: Robert Cozens <Robert.Cozens@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NMichael Trimarchi <trimarchimichael@yahoo.it>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

- simplifies irq set freq
- ioctl() was duplicating functionalities of rtc-dev core
- corrected initialization sequence
- use platform_driver_probe
Signed-off-by: NAlessandro Zummo <a.zummo@towertech.it>
Cc: Angelo Castello <angelo.castello@st.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Jamie Lenehan <lenehan@twibble.org>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

- removed spinlock protection, it's handled by the rtc class
- use platform_driver_probe
- return appropriate code for rtc_read_time
- style issues
Signed-off-by: NAlessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

-tip can't be bothered keeping interfaces stable long enough for anyone
to use them without having their builds broken without notification, so
just ifdef around the problematic symbols until the new interfaces become
available upstream.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add USB gadget support for port CN26 on the Solution Engine 7724
board. The r8a66597-udc driver is hooked up as a platform device
and some registers are configured to enable the USB in gadget mode.
The hardware driving the USB port is the on-chip USB1 block in
the sh7724 processor configured as USB gadget controller.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add USB gadget support for port YC301 on the KFR2R09 board.

The r8a66597-udc driver is hooked up as a platform device,
clocks are enabled via I2C and some registers are configured
to enable the USB in gadget mode. The hardware driving the
USB port is the on-chip USB0 block in the sh7724 processor
configured as USB gadget controller.

This board is using external hardware to detect USB hotplug
events and allows the processor to dynamically start and stop
clocks. This well thought out hardware feature is unused at
this point and plug and play is unfortunately unsupported.
To properly support all hardware features the USB gadget
stack may need some adjustment.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch improves the disable_controller() function in the
r8a66597-udc driver to disable all interrupts and also clear
status flags. With this patch in place the driver survives
kexec.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch updates the r8a66597-udc buffer management code.

Use fixed buffers for bulk and isochronous pipes, also make
sure to handle the isochronous-as-bulk case. With fixed buffers
there is no need to keep track of used buffers with bi_bufnum.

Also, this fixes a potential buffer offset problem where the
base offset incorrectly varies with the number of pipes used.

The m66592 driver recently got fixed in a similar way.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add support for the clock framework to the r8a66597 gadget driver.
This is needed to control the clock driving the USB block.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

While in-tree support for the R8A66597 host side has been supported for
some time, the peripheral side has so far been unsupported. This adds a
new USB gadget driver which bridges the gap and finally wires up the
peripheral side as well.
Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Tested-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This adds preliminary support for the EcoVec board.
Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch also update help comment
Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

While most platforms implement LED banks in sets of 8/16/32, some use
different configurations. This adds a LED mask to the heartbeat platform
data to allow platforms to constrain the bitmap, which is otherwise
derived from the register size.
Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch updates the FRQCRA.IFC divisor values for SH7724. Despite
not being initially documented, the / 3 mode is also support for the IFC
division.
Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

FLLFRQ setting is needed to use correct PLL clock for kfr2409.
Signed-off-by: NKuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>