Skip to content

cloud-kernel
cloud-kernel

openanolis / cloud-kernel
接近 2 年 前同步成功

通知 170
Star 36
Fork 7
cloud-kernel
cloud-kernel
切换分支/标签
  1. 19 1月, 2013 1 次提交
    • J
      tty: Added a CONFIG_TTY option to allow removal of TTY · 4f73bc4d
      由 Joe Millenbach 提交于 
      The option allows you to remove TTY and compile without errors. This
saves space on systems that won't support TTY interfaces anyway.
bloat-o-meter output is below.

The bulk of this patch consists of Kconfig changes adding "depends on
TTY" to various serial devices and similar drivers that require the TTY
layer.  Ideally, these dependencies would occur on a common intermediate
symbol such as SERIO, but most drivers "select SERIO" rather than
"depends on SERIO", and "select" does not respect dependencies.

bloat-o-meter output comparing our previous minimal to new minimal by
removing TTY.  The list is filtered to not show removed entries with awk
'$3 != "-"' as the list was very long.

add/remove: 0/226 grow/shrink: 2/14 up/down: 6/-35356 (-35350)
function                                     old     new   delta
chr_dev_init                                 166     170      +4
allow_signal                                  80      82      +2
static.__warned                              143     142      -1
disallow_signal                               63      62      -1
__set_special_pids                            95      94      -1
unregister_console                           126     121      -5
start_kernel                                 546     541      -5
register_console                             593     588      -5
copy_from_user                                45      40      -5
sys_setsid                                   128     120      -8
sys_vhangup                                   32      19     -13
do_exit                                     1543    1526     -17
bitmap_zero                                   60      40     -20
arch_local_irq_save                          137     117     -20
release_task                                 674     652     -22
static.spin_unlock_irqrestore                308     260     -48
Signed-off-by: NJoe Millenbach <jmillenbach@gmail.com>
Reviewed-by: NJamey Sharp <jamey@minilop.net>
Reviewed-by: NJosh Triplett <josh@joshtriplett.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      4f73bc4d
  3. 06 10月, 2012 1 次提交
  5. 19 9月, 2012 1 次提交
  7. 18 9月, 2012 1 次提交
  9. 25 2月, 2012 2 次提交
  11. 02 11月, 2011 1 次提交
  13. 17 10月, 2011 1 次提交
    • H
      PM / VT: Cleanup #if defined uglyness and fix compile error · 37cce26b
      由 H Hartley Sweeten 提交于 
      Introduce the config option CONFIG_VT_CONSOLE_SLEEP in order to cleanup
the #if defined ugliness for the vt suspend support functions. Note that
CONFIG_VT_CONSOLE is already dependant on CONFIG_VT.

The function pm_set_vt_switch is actually dependant on CONFIG_VT and not
CONFIG_PM_SLEEP. This fixes a compile error when CONFIG_PM_SLEEP is
not set:

drivers/tty/vt/vt_ioctl.c:1794: error: redefinition of 'pm_set_vt_switch'
include/linux/suspend.h:17: error: previous definition of 'pm_set_vt_switch' was here

Also, remove the incorrect path from the comment in console.c.

[rjw: Replaced #if defined() with #ifdef in suspend.h.]
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
      37cce26b
  15. 13 10月, 2011 1 次提交
  17. 24 8月, 2011 1 次提交
    • T
      tty/powerpc: introduce the ePAPR embedded hypervisor byte channel driver · dcd83aaf
      由 Timur Tabi 提交于 
      The ePAPR embedded hypervisor specification provides an API for "byte
channels", which are serial-like virtual devices for sending and receiving
streams of bytes.  This driver provides Linux kernel support for byte
channels via three distinct interfaces:

1) An early-console (udbg) driver.  This provides early console output
through a byte channel.  The byte channel handle must be specified in a
Kconfig option.

2) A normal console driver.  Output is sent to the byte channel designated
for stdout in the device tree.  The console driver is for handling kernel
printk calls.

3) A tty driver, which is used to handle user-space input and output.  The
byte channel used for the console is designated as the default tty.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      dcd83aaf
  19. 14 5月, 2011 1 次提交
    • J
      n_tracerouter and n_tracesink ldisc additions. · ee4f6b4b
      由 J Freyensee 提交于 
      The n_tracerouter and n_tracesink line discpline drivers use the
Linux tty line discpline framework to route trace data coming
from a tty port (say UART for example) to the trace sink line
discipline driver and to another tty port(say USB).  Those
these two line discipline drivers can be used together,
independently from pti.c, they are part of the original
implementation solution of the MIPI P1149.7, compact JTAG, PTI
solution for Intel mobile platforms starting with the
Medfield platform.
Signed-off-by: NJ Freyensee <james_p_freyensee@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
      ee4f6b4b
  21. 23 2月, 2011 2 次提交
  23. 21 1月, 2011 1 次提交
    • T
      h8300: Use generic irq Kconfig · 51f3f159
      由 Thomas Gleixner 提交于 
      Switch to the generic irq Kconfig. h8300 has all irq chips converted
to the new functions, so select the GENERIC_HARDIRQS_NO_DEPRECATED
switch as well. Fixup the resulting fallout in show_interrupts().
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Paul Mundt <lethal@linux-sh.org>
      51f3f159
  25. 20 9月, 2010 1 次提交
  27. 27 7月, 2010 1 次提交
  29. 15 12月, 2009 1 次提交
    • A
      module: make MODULE_SYMBOL_PREFIX into a CONFIG option · 9e1b9b80
      由 Alan Jenkins 提交于 
      The next commit will require the use of MODULE_SYMBOL_PREFIX in
.tmp_exports-asm.S.  Currently it is mixed in with C structure
definitions in "asm/module.h".  Move the definition of this arch option
into Kconfig, so it can be easily accessed by any code.

This also lets modpost.c use the same definition.  Previously modpost
relied on a hardcoded list of architectures in mk_elfconfig.c.

A build test for blackfin, one of the two MODULE_SYMBOL_PREFIX archs,
showed the generated code was unchanged.  vmlinux was identical save
for build ids, and an apparently randomized suffix on a single "__key"
symbol in the kallsyms data).
Signed-off-by: NAlan Jenkins <alan-jenkins@tuffmail.co.uk>
Acked-by: Mike Frysinger <vapier@gentoo.org> (blackfin)
CC: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
      9e1b9b80
  31. 07 1月, 2009 1 次提交
  33. 20 10月, 2008 1 次提交
    • M
      container freezer: implement freezer cgroup subsystem · dc52ddc0
      由 Matt Helsley 提交于 
      This patch implements a new freezer subsystem in the control groups
framework.  It provides a way to stop and resume execution of all tasks in
a cgroup by writing in the cgroup filesystem.

The freezer subsystem in the container filesystem defines a file named
freezer.state.  Writing "FROZEN" to the state file will freeze all tasks
in the cgroup.  Subsequently writing "RUNNING" will unfreeze the tasks in
the cgroup.  Reading will return the current state.

* Examples of usage :

   # mkdir /containers/freezer
   # mount -t cgroup -ofreezer freezer  /containers
   # mkdir /containers/0
   # echo $some_pid > /containers/0/tasks

to get status of the freezer subsystem :

   # cat /containers/0/freezer.state
   RUNNING

to freeze all tasks in the container :

   # echo FROZEN > /containers/0/freezer.state
   # cat /containers/0/freezer.state
   FREEZING
   # cat /containers/0/freezer.state
   FROZEN

to unfreeze all tasks in the container :

   # echo RUNNING > /containers/0/freezer.state
   # cat /containers/0/freezer.state
   RUNNING

This is the basic mechanism which should do the right thing for user space
task in a simple scenario.

It's important to note that freezing can be incomplete.  In that case we
return EBUSY.  This means that some tasks in the cgroup are busy doing
something that prevents us from completely freezing the cgroup at this
time.  After EBUSY, the cgroup will remain partially frozen -- reflected
by freezer.state reporting "FREEZING" when read.  The state will remain
"FREEZING" until one of these things happens:

	1) Userspace cancels the freezing operation by writing "RUNNING" to
		the freezer.state file
	2) Userspace retries the freezing operation by writing "FROZEN" to
		the freezer.state file (writing "FREEZING" is not legal
		and returns EIO)
	3) The tasks that blocked the cgroup from entering the "FROZEN"
		state disappear from the cgroup's set of tasks.

[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: export thaw_process]
Signed-off-by: NCedric Le Goater <clg@fr.ibm.com>
Signed-off-by: NMatt Helsley <matthltc@us.ibm.com>
Acked-by: NSerge E. Hallyn <serue@us.ibm.com>
Tested-by: NMatt Helsley <matthltc@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      dc52ddc0
  35. 17 10月, 2008 1 次提交
  37. 17 9月, 2008 1 次提交
  39. 07 9月, 2008 1 次提交
  41. 26 7月, 2008 1 次提交
  43. 09 2月, 2008 3 次提交
    • S
      ide: introduce HAVE_IDE · ec7748b5
      由 Sam Ravnborg 提交于 
      To allow flexible configuration of IDE introduce HAVE_IDE.
All archs except arm, um and s390 unconditionally select it.
For arm the actual configuration determine if IDE is supported.

This is a step towards introducing drivers/Kconfig for arm.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Acked-by: NRussell King - ARM Linux <linux@arm.linux.org.uk>
Acked-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
      ec7748b5
    • H
      avoid overflows in kernel/time.c · bdc80787
      由 H. Peter Anvin 提交于 
      When the conversion factor between jiffies and milli- or microseconds is
not a single multiply or divide, as for the case of HZ == 300, we currently
do a multiply followed by a divide.  The intervening result, however, is
subject to overflows, especially since the fraction is not simplified (for
HZ == 300, we multiply by 300 and divide by 1000).

This is exposed to the user when passing a large timeout to poll(), for
example.

This patch replaces the multiply-divide with a reciprocal multiplication on
32-bit platforms.  When the input is an unsigned long, there is no portable
way to do this on 64-bit platforms there is no portable way to do this
since it requires a 128-bit intermediate result (which gcc does support on
64-bit platforms but may generate libgcc calls, e.g.  on 64-bit s390), but
since the output is a 32-bit integer in the cases affected, just simplify
the multiply-divide (*3/10 instead of *300/1000).

The reciprocal multiply used can have off-by-one errors in the upper half
of the valid output range.  This could be avoided at the expense of having
to deal with a potential 65-bit intermediate result.  Since the intent is
to avoid overflow problems and most of the other time conversions are only
semiexact, the off-by-one errors were considered an acceptable tradeoff.

At Ralf Baechle's suggestion, this version uses a Perl script to compute
the necessary constants.  We already have dependencies on Perl for kernel
compiles.  This does, however, require the Perl module Math::BigInt, which
is included in the standard Perl distribution starting with version 5.8.0.
In order to support older versions of Perl, include a table of canned
constants in the script itself, and structure the script so that
Math::BigInt isn't required if pulling values from said table.

Running the script requires that the HZ value is available from the
Makefile.  Thus, this patch also adds the Kconfig variable CONFIG_HZ to the
architectures which didn't already have it (alpha, cris, frv, h8300, m32r,
m68k, m68knommu, sparc, v850, and xtensa.) It does *not* touch the sh or
sh64 architectures, since Paul Mundt has dealt with those separately in the
sh tree.
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>
Cc: Ralf Baechle <ralf@linux-mips.org>,
Cc: Sam Ravnborg <sam@ravnborg.org>,
Cc: Paul Mundt <lethal@linux-sh.org>,
Cc: Richard Henderson <rth@twiddle.net>,
Cc: Michael Starvik <starvik@axis.com>,
Cc: David Howells <dhowells@redhat.com>,
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>,
Cc: Hirokazu Takata <takata@linux-m32r.org>,
Cc: Geert Uytterhoeven <geert@linux-m68k.org>,
Cc: Roman Zippel <zippel@linux-m68k.org>,
Cc: William L. Irwin <sparclinux@vger.kernel.org>,
Cc: Chris Zankel <chris@zankel.net>,
Cc: H. Peter Anvin <hpa@zytor.com>,
Cc: Jan Engelhardt <jengelh@computergmbh.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      bdc80787
    • D
      aout: mark arches that support A.OUT format · b0b933c0
      由 David Howells 提交于 
      Mark arches that support A.OUT format by including the following in their
master Kconfig files:

	config ARCH_SUPPORTS_AOUT
		def_bool y

This should also be set if the arch provides compatibility A.OUT support for
an older arch, for instance x86_64 for i386 or sparc64 for sparc.

I've guessed at which arches don't, based on comments in the code, however I'm
sure that some of the ones I've marked as 'yes' actually should be 'no'.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      b0b933c0
  45. 03 2月, 2008 1 次提交
  47. 31 10月, 2007 1 次提交
  49. 20 10月, 2007 1 次提交
  51. 17 7月, 2007 1 次提交
    • D
      dma-mapping: prevent dma dependent code from linking on !HAS_DMA archs · 1b0fac45
      由 Dan Williams 提交于 
      Continuing the work started in 411f0f3e ...

This enables code with a dma path, that compiles away, to build without
requiring additional code factoring.  It also prevents code that calls
dma_alloc_coherent and dma_free_coherent from linking whereas previously
the code would hit a BUG() at run time.  Finally, it allows archs that set
!HAS_DMA to delete their asm/dma-mapping.h file.

Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Kyle McMartin <kyle@parisc-linux.org>
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: <geert@linux-m68k.org>
Cc: <zippel@linux-m68k.org>
Cc: <spyro@f2s.com>
Cc: <ysato@users.sourceforge.jp>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      1b0fac45
  53. 08 5月, 2007 2 次提交
  55. 12 2月, 2007 2 次提交
    • A
      [PATCH] sort the devres mess out · 5ea81769
      由 Al Viro 提交于 
      * Split the implementation-agnostic stuff in separate files.
* Make sure that targets using non-default request_irq() pull
  kernel/irq/devres.o
* Introduce new symbols (HAS_IOPORT and HAS_IOMEM) defaulting to positive;
  allow architectures to turn them off (we needed these symbols anyway for
  dependencies of quite a few drivers).
* protect the ioport-related parts of lib/devres.o with CONFIG_HAS_IOPORT.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      5ea81769
    • C
      [PATCH] optional ZONE_DMA: introduce CONFIG_ZONE_DMA · 66701b14
      由 Christoph Lameter 提交于 
      This patch simply defines CONFIG_ZONE_DMA for all arches.  We later do special
things with CONFIG_ZONE_DMA after the VM and an arch are prepared to work
without ZONE_DMA.

CONFIG_ZONE_DMA can be defined in two ways depending on how an architecture
handles ISA DMA.

First if CONFIG_GENERIC_ISA_DMA is set by the arch then we know that the arch
needs ZONE_DMA because ISA DMA devices are supported.  We can catch this in
mm/Kconfig and do not need to modify arch code.

Second, arches may use ZONE_DMA in an unknown way.  We set CONFIG_ZONE_DMA for
all arches that do not set CONFIG_GENERIC_ISA_DMA in order to insure backwards
compatibility.  The arches may later undefine ZONE_DMA if their arch code has
been verified to not depend on ZONE_DMA.
Signed-off-by: NChristoph Lameter <clameter@sgi.com>
Cc: Andi Kleen <ak@suse.de>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Matthew Wilcox <willy@debian.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      66701b14
  57. 09 12月, 2006 1 次提交
    • D
      [PATCH] LOG2: Implement a general integer log2 facility in the kernel · f0d1b0b3
      由 David Howells 提交于 
      This facility provides three entry points:

	ilog2()		Log base 2 of unsigned long
	ilog2_u32()	Log base 2 of u32
	ilog2_u64()	Log base 2 of u64

These facilities can either be used inside functions on dynamic data:

	int do_something(long q)
	{
		...;
		y = ilog2(x)
		...;
	}

Or can be used to statically initialise global variables with constant values:

	unsigned n = ilog2(27);

When performing static initialisation, the compiler will report "error:
initializer element is not constant" if asked to take a log of zero or of
something not reducible to a constant.  They treat negative numbers as
unsigned.

When not dealing with a constant, they fall back to using fls() which permits
them to use arch-specific log calculation instructions - such as BSR on
x86/x86_64 or SCAN on FRV - if available.

[akpm@osdl.org: MMC fix]
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: David Howells <dhowells@redhat.com>
Cc: Wojtek Kaniewski <wojtekka@toxygen.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
      f0d1b0b3
  59. 27 3月, 2006 1 次提交
  61. 15 2月, 2006 1 次提交
  63. 09 1月, 2006 1 次提交
  65. 12 7月, 2005 2 次提交