- 06 4月, 2016 18 次提交
-
-
由 Johannes Berg 提交于
When storing the last_rate_* values in the RX code, there's nothing to guarantee consistency, so a concurrent reader could see, e.g. last_rate_idx on the new value, but last_rate_flag still on the old, getting completely bogus values in the end. To fix this, I lifted the sta_stats_encode_rate() function from my old rate statistics code, which encodes the entire rate data into a single 16-bit value, avoiding the consistency issue. Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Johannes Berg 提交于
Instead of touching the rx_stats.last_rx from the status path, introduce and use a status_stats.last_ack variable. This will make rx_stats.last_rx indicate when the last frame was received, making it available for real "last_rx" and statistics gathering; statistics, when done per-CPU, will need to figure out which place was updated last for those items where the "last" value is exposed. Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Johannes Berg 提交于
There's no need to update rx_stats.last_rx after allocating a station since it's already updated during allocation. Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Johannes Berg 提交于
Move the averaged values out of rx_stats and into rx_stats_avg, to cleanly split them out. The averaged ones cannot be supported for parallel RX in a per-CPU fashion, while the other values can be collected per CPU and then combined/selected when needed. Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Johannes Berg 提交于
Move the semicolon, people typically assume that and once line already put a semicolon behind the "call". Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Johannes Berg 提交于
For the RX MSDU statistics, we need to count the number of MSDUs created and accepted from an A-MSDU. Right now, all frames in any A-MSDUs were completely ignored. Fix this by moving the RX MSDU statistics accounting into the deliver function. Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Johannes Berg 提交于
Sometimes drivers already looked up, or know out-of-band from their device, which station transmitted a given RX frame. Allow them to pass the station pointer to mac80211 to save the extra lookup. Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Bob Copeland 提交于
Lockdep warned of a lock dependency between the mesh_plink lock and the internal lock for the rhashtable. The problem is that the rhashtable code uses a spin lock with softirqs enabled, while mesh_plink_timer executes a walk (to flush paths on a state change) inside a softirq with the plink lock held. This leads to the following deadlock if the timer fires while rht lock is held on this CPU, and plink lock is held on another CPU: CPU0 CPU1 ---- ---- lock(&(&ht->lock)->rlock); local_irq_disable(); lock(&(&sta->mesh->plink_lock)->rlock); lock(&(&ht->lock)->rlock); <Interrupt> lock(&(&sta->mesh->plink_lock)->rlock); *** DEADLOCK *** Fix by waiting until we drop the plink lock to flush paths. Fixes: d48a1b7cd439 ("mac80211: mesh: convert path table to rhashtable") Signed-off-by: NBob Copeland <me@bobcopeland.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Bob Copeland 提交于
The mesh path table needs to be around for the entire time the interface is in mesh mode, as users can perform an mpath dump at any time. The existing path table lifetime is instead tied to the mesh BSS which can cause crashes when different MBSSes are joined in the context of a single interface, or when the path table is dumped when no MBSS is joined. Introduce a new function to perform the final teardown of the interface and perform path table cleanup there. We already free the individual path elements when the leaving the mesh so no additional cleanup is needed there. This fixes the following crash: [ 47.753026] BUG: unable to handle kernel paging request at fffffff0 [ 47.753026] IP: [<c0239765>] kthread_data+0xa/0xe [ 47.753026] *pde = 00741067 *pte = 00000000 [ 47.753026] Oops: 0000 [#4] PREEMPT [ 47.753026] Modules linked in: ppp_generic slhc 8021q garp mrp sch_fq_codel iptable_mangle ipt_MASQUERADE nf_nat_masquerade_ipv4 iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat ip_tables ath9k_htc ath5k 8139too ath10k_pci ath10k_core arc4 ath9k ath9k_common ath9k_hw mac80211 ath cfg80211 cpufreq_powersave br_netfilter bridge stp llc ipw usb_wwan sierra_net usbnet af_alg natsemi via_rhine mii iTCO_wdt iTCO_vendor_support gpio_ich sierra coretemp pcspkr i2c_i801 lpc_ich ata_generic ata_piix libata ide_pci_generic piix e1000e igb i2c_algo_bit ptp pps_core [last unloaded: 8139too] [ 47.753026] CPU: 0 PID: 12 Comm: kworker/u2:1 Tainted: G D W 4.5.0-wt-V3 #6 [ 47.753026] Hardware name: To Be Filled By O.E.M./To be filled by O.E.M., BIOS 080016 11/07/2014 [ 47.753026] task: f645a0c0 ti: f6462000 task.ti: f6462000 [ 47.753026] EIP: 0060:[<c0239765>] EFLAGS: 00010002 CPU: 0 [ 47.753026] EIP is at kthread_data+0xa/0xe [ 47.753026] EAX: 00000000 EBX: 00000000 ECX: 00000000 EDX: 00000000 [ 47.753026] ESI: f645a0c0 EDI: f645a2fc EBP: f6463a80 ESP: f6463a78 [ 47.753026] DS: 007b ES: 007b FS: 0000 GS: 0000 SS: 0068 [ 47.753026] CR0: 8005003b CR2: 00000014 CR3: 353e5000 CR4: 00000690 [ 47.753026] Stack: [ 47.753026] c0236866 00000000 f6463aac c05768b4 00000009 f6463ba8 f6463ab0 c0247010 [ 47.753026] 00000000 f645a0c0 f6464000 00000009 f6463ba8 f6463ab8 c0576eb2 f645a0c0 [ 47.753026] f6463aec c0228be4 c06335a4 f6463adc f6463ad0 c06c06d4 f6463ae4 c02471b0 [ 47.753026] Call Trace: [ 47.753026] [<c0236866>] ? wq_worker_sleeping+0xb/0x78 [ 47.753026] [<c05768b4>] __schedule+0xda/0x587 [ 47.753026] [<c0247010>] ? vprintk_default+0x12/0x14 [ 47.753026] [<c0576eb2>] schedule+0x72/0x89 [ 47.753026] [<c0228be4>] do_exit+0xb8/0x71d [ 47.753026] [<c02471b0>] ? kmsg_dump+0xa9/0xae [ 47.753026] [<c0203576>] oops_end+0x69/0x70 [ 47.753026] [<c021dcdb>] no_context+0x1bb/0x1c5 [ 47.753026] [<c021de1b>] __bad_area_nosemaphore+0x136/0x140 [ 47.753026] [<c021e2ef>] ? vmalloc_sync_all+0x19a/0x19a [ 47.753026] [<c021de32>] bad_area_nosemaphore+0xd/0x10 [ 47.753026] [<c021e0a1>] __do_page_fault+0x26c/0x320 [ 47.753026] [<c021e2ef>] ? vmalloc_sync_all+0x19a/0x19a [ 47.753026] [<c021e2fa>] do_page_fault+0xb/0xd [ 47.753026] [<c05798f8>] error_code+0x58/0x60 [ 47.753026] [<c021e2ef>] ? vmalloc_sync_all+0x19a/0x19a [ 47.753026] [<c0239765>] ? kthread_data+0xa/0xe [ 47.753026] [<c0236866>] ? wq_worker_sleeping+0xb/0x78 [ 47.753026] [<c05768b4>] __schedule+0xda/0x587 [ 47.753026] [<c0247010>] ? vprintk_default+0x12/0x14 [ 47.753026] [<c0576eb2>] schedule+0x72/0x89 [ 47.753026] [<c0228be4>] do_exit+0xb8/0x71d [ 47.753026] [<c02471b0>] ? kmsg_dump+0xa9/0xae [ 47.753026] [<c0203576>] oops_end+0x69/0x70 [ 47.753026] [<c021dcdb>] no_context+0x1bb/0x1c5 [ 47.753026] [<c021de1b>] __bad_area_nosemaphore+0x136/0x140 [ 47.753026] [<c021e2ef>] ? vmalloc_sync_all+0x19a/0x19a [ 47.753026] [<c021de32>] bad_area_nosemaphore+0xd/0x10 [ 47.753026] [<c021e0a1>] __do_page_fault+0x26c/0x320 [ 47.753026] [<c021e2ef>] ? vmalloc_sync_all+0x19a/0x19a [ 47.753026] [<c021e2fa>] do_page_fault+0xb/0xd [ 47.753026] [<c05798f8>] error_code+0x58/0x60 [ 47.753026] [<c021e2ef>] ? vmalloc_sync_all+0x19a/0x19a [ 47.753026] [<c0239765>] ? kthread_data+0xa/0xe [ 47.753026] [<c0236866>] ? wq_worker_sleeping+0xb/0x78 [ 47.753026] [<c05768b4>] __schedule+0xda/0x587 [ 47.753026] [<c0391e32>] ? put_io_context_active+0x6d/0x95 [ 47.753026] [<c0576eb2>] schedule+0x72/0x89 [ 47.753026] [<c02291f8>] do_exit+0x6cc/0x71d [ 47.753026] [<c0203576>] oops_end+0x69/0x70 [ 47.753026] [<c021dcdb>] no_context+0x1bb/0x1c5 [ 47.753026] [<c021de1b>] __bad_area_nosemaphore+0x136/0x140 [ 47.753026] [<c021e2ef>] ? vmalloc_sync_all+0x19a/0x19a [ 47.753026] [<c021de32>] bad_area_nosemaphore+0xd/0x10 [ 47.753026] [<c021e0a1>] __do_page_fault+0x26c/0x320 [ 47.753026] [<c03b9160>] ? debug_smp_processor_id+0x12/0x16 [ 47.753026] [<c02015e2>] ? __switch_to+0x24/0x40e [ 47.753026] [<c021e2ef>] ? vmalloc_sync_all+0x19a/0x19a [ 47.753026] [<c021e2fa>] do_page_fault+0xb/0xd [ 47.753026] [<c05798f8>] error_code+0x58/0x60 [ 47.753026] [<c021e2ef>] ? vmalloc_sync_all+0x19a/0x19a [ 47.753026] [<c03b59d2>] ? rhashtable_walk_init+0x5c/0x93 [ 47.753026] [<f9843221>] mesh_path_tbl_expire.isra.24+0x19/0x82 [mac80211] [ 47.753026] [<f984408b>] mesh_path_expire+0x11/0x1f [mac80211] [ 47.753026] [<f9842bb7>] ieee80211_mesh_work+0x73/0x1a9 [mac80211] [ 47.753026] [<f98207d1>] ieee80211_iface_work+0x2ff/0x311 [mac80211] [ 47.753026] [<c0235fa3>] process_one_work+0x14b/0x24e [ 47.753026] [<c0236313>] worker_thread+0x249/0x343 [ 47.753026] [<c02360ca>] ? process_scheduled_works+0x24/0x24 [ 47.753026] [<c0239359>] kthread+0x9e/0xa3 [ 47.753026] [<c0578e50>] ret_from_kernel_thread+0x20/0x40 [ 47.753026] [<c02392bb>] ? kthread_parkme+0x18/0x18 [ 47.753026] Code: 6b c0 85 c0 75 05 e8 fb 74 fc ff 89 f8 84 c0 75 08 8d 45 e8 e8 34 dd 33 00 83 c4 28 5b 5e 5f 5d c3 55 8b 80 10 02 00 00 89 e5 5d <8b> 40 f0 c3 55 b9 04 00 00 00 89 e5 52 8b 90 10 02 00 00 8d 45 [ 47.753026] EIP: [<c0239765>] kthread_data+0xa/0xe SS:ESP 0068:f6463a78 [ 47.753026] CR2: 00000000fffffff0 [ 47.753026] ---[ end trace 867ca0bdd0767790 ]--- Fixes: 3b302ada7f0a ("mac80211: mesh: move path tables into if_mesh") Reported-by: NFred Veldini <fred.veldini@gmail.com> Signed-off-by: NBob Copeland <me@bobcopeland.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Bob Copeland 提交于
Several of the mesh path fields are undocumented and some of the documentation is no longer correct or relevant after the switch to rhashtable. Clean up the kernel doc accordingly and reorder some fields to match the structure layout. Signed-off-by: NBob Copeland <me@bobcopeland.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Bob Copeland 提交于
Reduce padding waste in struct mesh_table and struct rmc_entry by moving the smaller fields to the end. Signed-off-by: NBob Copeland <me@bobcopeland.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Bob Copeland 提交于
Since we have converted the mesh path tables to rhashtable, we are no longer swapping out the entire mesh_pathtbl pointer with RCU. As a result, we no longer need indirection to the hlist head for the gates list and can simply embed it, saving a pair of pointer-sized allocations. Signed-off-by: NBob Copeland <me@bobcopeland.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Bob Copeland 提交于
The RMC cache has 256 list heads plus a u32, which puts it at the unfortunate size of 4104 bytes with padding. kmalloc() will then round this up to the next power-of-two, so we wind up actually using two pages here where most of the second is wasted. Switch to hlist heads here to reduce the structure size down to fit within a page. Signed-off-by: NBob Copeland <me@bobcopeland.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Bob Copeland 提交于
In the unlikely case that mesh_rmc_init() fails with -ENOMEM, the rmc pointer will be left as NULL but the interface is still operational because ieee80211_mesh_init_sdata() is not allowed to fail. If this happens, we would blindly dereference rmc when checking whether a multicast frame is in the cache. Instead just drop the frames in the forwarding path. Signed-off-by: NBob Copeland <me@bobcopeland.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Bob Copeland 提交于
The mesh_path_reclaim() function, called from an rcu callback, cancels the mesh_path_timer associated with a mesh path. Unfortunately, this call can happen much later, perhaps after the hash table itself is destroyed. Such a situation led to the following crash in mesh_path_send_to_gates() when dereferencing the tbl pointer: [ 23.901661] BUG: unable to handle kernel NULL pointer dereference at 0000000000000008 [ 23.905516] IP: [<ffffffff814c910b>] mesh_path_send_to_gates+0x2b/0x740 [ 23.908757] PGD 99ca067 PUD 99c4067 PMD 0 [ 23.910789] Oops: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC [ 23.913485] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.5.0-rc6-wt+ #43 [ 23.916675] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Debian-1.8.2-1 04/01/2014 [ 23.920471] task: ffffffff81685500 ti: ffffffff81678000 task.ti: ffffffff81678000 [ 23.922619] RIP: 0010:[<ffffffff814c910b>] [<ffffffff814c910b>] mesh_path_send_to_gates+0x2b/0x740 [ 23.925237] RSP: 0018:ffff88000b403d30 EFLAGS: 00010286 [ 23.926739] RAX: 0000000000000000 RBX: ffff880009bc0d20 RCX: 0000000000000102 [ 23.928796] RDX: 000000000000002e RSI: 0000000000000001 RDI: ffff880009bc0d20 [ 23.930895] RBP: ffff88000b403e18 R08: 0000000000000001 R09: 0000000000000001 [ 23.932917] R10: 0000000000000000 R11: 0000000000000001 R12: ffff880009c20940 [ 23.936370] R13: ffff880009bc0e70 R14: ffff880009c21c40 R15: ffff880009bc0d20 [ 23.939823] FS: 0000000000000000(0000) GS:ffff88000b400000(0000) knlGS:0000000000000000 [ 23.943688] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b [ 23.946429] CR2: 0000000000000008 CR3: 00000000099c5000 CR4: 00000000000006b0 [ 23.949861] Stack: [ 23.950840] 000000000000002e ffff880009c20940 ffff88000b403da8 ffffffff8109e551 [ 23.954467] ffffffff82711be2 000000000000002e 0000000000000000 ffffffff8166a5f5 [ 23.958141] 0000000000685ce8 0000000000000246 ffff880009bc0d20 ffff880009c20940 [ 23.961801] Call Trace: [ 23.962987] <IRQ> [ 23.963963] [<ffffffff8109e551>] ? vprintk_emit+0x351/0x5e0 [ 23.966782] [<ffffffff8109e8ff>] ? vprintk_default+0x1f/0x30 [ 23.969529] [<ffffffff810ffa41>] ? printk+0x48/0x50 [ 23.971956] [<ffffffff814ceef3>] mesh_path_timer+0x133/0x160 [ 23.974707] [<ffffffff814cedc0>] ? mesh_nexthop_resolve+0x230/0x230 [ 23.977775] [<ffffffff810b04ee>] call_timer_fn+0xce/0x330 [ 23.980448] [<ffffffff810b0425>] ? call_timer_fn+0x5/0x330 [ 23.983126] [<ffffffff814cedc0>] ? mesh_nexthop_resolve+0x230/0x230 [ 23.986091] [<ffffffff810b097c>] run_timer_softirq+0x22c/0x390 Instead of cancelling in the RCU callback, set a new flag to prevent the timer from being rearmed, and then cancel the timer synchronously when freeing the mesh path. This leaves mesh_path_reclaim() doing nothing but kfree, so switch to kfree_rcu(). Fixes: 3b302ada7f0a ("mac80211: mesh: move path tables into if_mesh") Signed-off-by: NBob Copeland <me@bobcopeland.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Ayala Beker 提交于
Legacy clients don't support P2P power save mechanism, and thus if a P2P GO has a legacy client connected to it, it should disable P2P PS mechanisms. Let the driver know about this with a new bss_conf parameter. Signed-off-by: NAyala Beker <ayala.beker@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Ayala Beker 提交于
Legacy clients don't support P2P power save mechanisms, and thus if a P2P GO has a legacy client connected to it, it has to make some changes in the PS behavior. To handle this, add an attribute to specify whether a station supports P2P PS or not. If the attribute was not specified cfg80211 will assume that station supports it for P2P GO interface, and does NOT support it for AP interface, matching the current assumptions in the code. Signed-off-by: NAyala Beker <ayala.beker@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Johannes Berg 提交于
In the likely case that probe_count is 0, don't write to the memory there. Also use ifmgd consistently in the function, instead of using sdata->u.mgd as well. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
- 05 4月, 2016 22 次提交
-
-
由 Johannes Berg 提交于
The code is only used with iwlwifi, but still should have proper mac80211 naming scheme; fix that. Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Johannes Berg 提交于
Avoid the really strange %s%s%s expression, use an array of flag names and check that all flags are present. Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Avraham Stern 提交于
Add definition for Fine Timing Measurement (FTM) frame format as defined in IEEE802.11-REVmcD5.0 section 9.6.8.33 Signed-off-by: NAvraham Stern <avraham.stern@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Johannes Berg 提交于
If the device implements dynamic PS itself, there's no need to ever start the dynamic powersave timer on RX. While at it, fix up some indentation in this code. Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Johannes Berg 提交于
Since the previous patch, the struct only has a single member, so remove the struct and leave just the single member. Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Mohammed Shafi Shajakhan 提交于
Remove unused variable in per STA debugfs structure, 'commit 34e89507 ("mac80211: allow station add/remove to sleep")' removed the only user of 'add_has_run'. Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qti.qualcomm.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Sara Sharon 提交于
Currently the debugfs entry for starting aggregation session starts it with timeout of 5 seconds. Allow opening a session with a custom timeout (according to spec 0 is no timeout). while at it, refactor the function and remove the magic numbers. Signed-off-by: NSara Sharon <sara.sharon@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Sara Sharon 提交于
NETIF_F_RXCSUM is not in the white list, though some drivers may want to set it in order to enable seeing the actual RX checksum status in ethtool. Signed-off-by: NSara Sharon <sara.sharon@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Emmanuel Grumbach 提交于
Allow publishing RRM capabilities for features that are not HW dependent. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Akira Moroo 提交于
This patch fix a structure name mismatch in cfg80211.h. Signed-off-by: NMoroo Akira <retrage01@gmail.com> Reviewed-by: NJulian Calaby <julian.calaby@gmail.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Felix Fietkau 提交于
There were a few issues that were slowing down the process of finding the optimal rate, especially on devices with multi-rate retry limitations: When max_tp_rate[0] was slower than max_tp_rate[1], the code did not sample max_tp_rate[1], which would often allow it to switch places with max_tp_rate[0] (e.g. if only the first sampling attempts were bad, but the rate is otherwise good). Also, sample attempts of rates between max_tp_rate[0] and [1] were being ignored in this case, because the code only checked if the rate was slower than [1]. Fix this by checking against the fastest / second fastest max_tp_rate instead of assuming a specific order between the two. In my tests this patch significantly reduces the time until minstrel_ht finds the optimal rate right after assoc Signed-off-by: NFelix Fietkau <nbd@openwrt.org> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Felix Fietkau 提交于
Fall back to rate control if the requested bitrate was not found. Fixes: dfdfc2be ("mac80211: Parse legacy and HT rate in injected frames") Signed-off-by: NFelix Fietkau <nbd@openwrt.org> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Sven Eckelmann 提交于
The MCS bandwidth part of the radiotap header is 2 bits wide. The full 2 bit have to compared against IEEE80211_RADIOTAP_MCS_BW_40 and not only if the first bit is set. Otherwise IEEE80211_RADIOTAP_MCS_BW_40 can be confused with IEEE80211_RADIOTAP_MCS_BW_20U. Fixes: dfdfc2be ("mac80211: Parse legacy and HT rate in injected frames") Signed-off-by: NSven Eckelmann <sven@narfation.org> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Arend van Spriel 提交于
Introducing a new feature that the driver can use to indicate the driver/firmware supports configuration of BSS selection criteria upon CONNECT command. This can be useful when multiple BSS-es are found belonging to the same ESS, ie. Infra-BSS with same SSID. The criteria can then be used to offload selection of a preferred BSS. Reviewed-by: NHante Meuleman <meuleman@broadcom.com> Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com> Reviewed-by: NLei Zhang <leizh@broadcom.com> Signed-off-by: NArend van Spriel <arend@broadcom.com> [move wiphy support check into parse_bss_select()] Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Sara Sharon 提交于
Some devices, like iwlwifi, have RSS queues. This may cause a situation where a disassociation is handled in control path and results in station removal while there are prior RX frames that were still not processed in other queues. When they will be processed the station will be gone, and the frames will be dropped. Add a synchronization interface to avoid that. When driver returns from the synchronization mac80211 may remove the station. Signed-off-by: NSara Sharon <sara.sharon@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Bob Copeland 提交于
In the time since the mesh path table was implemented as an RCU-traversable, dynamically growing hash table, a generic RCU hashtable implementation was added to the kernel. Switch the mesh path table over to rhashtable to remove some code and also gain some features like automatic shrinking. Cc: Thomas Graf <tgraf@suug.ch> Cc: netdev@vger.kernel.org Signed-off-by: NBob Copeland <me@bobcopeland.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Bob Copeland 提交于
In certain cases, the 802.11 mesh pathtable code wants to iterate over all of the entries in the forwarding table from the receive path, which is inside an RCU read-side critical section. Enable walks inside atomic sections by allowing GFP_ATOMIC allocations for the walker state. Change all existing callsites to pass in GFP_KERNEL. Acked-by: NThomas Graf <tgraf@suug.ch> Signed-off-by: NBob Copeland <me@bobcopeland.com> [also adjust gfs2/glock.c and rhashtable tests] Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Bob Copeland 提交于
The mesh path table uses a struct mesh_node in its hlists in order to support a resizable hash table: the mesh_node provides an indirection to the actual mesh path so that two different bucket lists can point to the same path entry. However, for the known gates list, we don't need this indirection because there is ever only one list. So we can just embed the hlist_node in the mesh path itself, which simplifies things a bit and saves a linear search whenever we need to find an item in the list. Signed-off-by: NBob Copeland <me@bobcopeland.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Bob Copeland 提交于
Remove duplicate code to allocate and initialize a mesh path or mesh proxy path. Signed-off-by: NBob Copeland <me@bobcopeland.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Bob Copeland 提交于
Now that the sdata pointer is the same for all entries of a path table, hashing it is pointless, so hash only the address. Signed-off-by: NBob Copeland <me@bobcopeland.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Bob Copeland 提交于
The mesh path and mesh gate hashtables are global, containing all of the mpaths for every mesh interface, but the paths are all tied logically to a single interface. The common case is just a single mesh interface, so optimize for that by moving the global hashtable into the per-interface struct. Doing so allows us to drop sdata pointer comparisons inside the lookups and also saves a few bytes of BSS and data. Signed-off-by: NBob Copeland <me@bobcopeland.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Jouni Malinen 提交于
If the hw scan request specifies a single BSSID, use that value instead of the wildcard BSSID in the Probe Request frames. Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-