Add code to enable thermal sensors for the x540 hardware, as well as a
thermal interrupt check which will exit with a critical message of a
thermal overheat is detected. Intent of code allows other mac types to
be added with different configuration in the future.

Fixed in this version is the addition of setting the temp_sensor
capable flag which was previously only set for a specific mac.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Revise high and low threshold marks wrt flow control to account
for the X540 devices and latency introduced by the loopback
switch.

Without this it was in theory possible to drop frames on a
supposedly lossless link with X540 or SR-IOV enabled.

Previously we used a magic number in a define to calculate the
threshold values. This made it difficult to sort out exactly
which latencies were or were not being accounted for. Here
I was overly explicit and tried to used #define names that would
be recognizable after reading the IEEE 802.1Qbb specification.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch is meant to help cleanup the interrupt throttle rate logic by
storing the interrupt throttle rate as a value in microseconds instead of
interrupts per second.  The advantage to this approach is that the value
can now be stored in an 16 bit field and doesn't require as much math to
flip the value back and forth since the hardware already used microseconds
when setting the rate.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add support for WOL as determined by the EEPROM.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We don't need SFP+ plugable support for X540 hardware (copper only) so
don't enable the SFP+ interrupts.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The DCB CEE command set_state() will complete successfully
but is misleading because it enables IEEE mode. After
this patch the command is failed.

And IEEE PFC/ETS is managed from ieee paths now instead
of using CEE primitives.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Use the PCI device flag indicating if a VF is assigned to a guest VM
to guard against destroying VFs upon driver removal.  Implement
additional feature to detect if VFs already exist when the driver
is loaded and if so configure them and set the driver state to
SR-IOV enabled.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

netif_tx_start_all_queues() is already called in ixgbe_up_complete, no need
to do it twice.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove duplicate inc of hwstats->ruc
Introduce separate loops for 8 and 16 register reads.
Consolidate mac checks under one case.
Make sure registers are cleared on read.
Reported-by: NJonathan Lynch <jonathan.lynch@thenowfactory.com>
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
CC: Jonathan Lynch <jonathan.lynch@thenowfactory.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch improves the memory utilization with RSC when in one-buffer
mode.  This is accomplished by making the default buffer sizes match up
with the standard memory allocation sizes minus 1K for shared info and
padding overhead.  By doing this CPU utilization when doing large receives
can be reduced by as much as 8%.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

One of the 82598 phys was not being correctly identified as being SFP.
This change corrects that.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change adds a small bit of missing code for enabling the overheat sensor
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

ixgbe_up and ixgbe_up_complete will always return 0.  Since this doesn't
provide any useful information we might as well just make them both void
and save ourselves from having to return an unused value.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change fixes an issue in which the incorrect amount of headroom was
being reserved for flow director filters.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change fixes a minor redundancy in that tx_sample_rate was set twice.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

It was possible to inadvertently add additional interrupt causes to the
MSI-X other interrupt.  This occurred when things such as RX buffer overrun
events were being triggered at the same time as an event such as a Flow
Director table reinit request.  In order to avoid this we should be
explicitly programming only the interrupts that we want enabled.  In
addition I am renaming the ixgbe_msix_lsc function and interrupt to drop
any implied meaning of this being a link status only interrupt.

Unfortunately the patch is a bit ugly due to the fact that ixgbe_irq_enable
needed to be moved up before ixgbe_msix_other in order to have things
defined in the correct order.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change is meant to cleanup some of the code related to SR-IOV and the
interrupt registers.  Specifically I am moving the EITRSEL configuration
into the MSI-X configuration section instead of enablement.  Also I am
fixing the VF shutdown path since it had operations in the incorrect order.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change updated the TXDCTL configuration.  The main goal is to be much
more explicit about the configuration and avoid a possible fake TX hang
when the interrupt throttle rate is set to 0.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch is a minor whitespace cleanup to compress the device ID
declaration and board type declaration onto the same line.  It seems to
make sense since all of the combinations of the two are less than 80
characters and it makes the overall layout a bit more readable.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch makes it so that the map_rings_to_vectors call will work with
all interrupt types.  The advantage to this is that there will now be a
predictable mapping for all given interrupt types.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change switches us over to using the ring->dev pointer instead of
having to use the adapter->pdev->dev reference.  The advantage to this is
that it is a much shorter route to get the to final needed value.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The allocation and freeing of the IRQ affinity hint needs some updates
since there are a number of spots where we run into possible issues with
the hint not being correctly updated.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change consolidates all of the MSI-X interrupt and polling routines
into two single functions.  One for the interrupt and one for the code.
The main advantage to doing this is that the compiler can optimize the
routines into single monolithic functions which should allow all of them
function to occupy a single block of memory and as such avoid jumping
around.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change makes it so that the default Tx work limit is 256 buffers or
1/2 of an entire ring instead of a full ring size so that it is much more
likely that we will be able to actually reach the work limit value.
Previously with the value set to an entire ring it would not have been
possible for us to trigger an event due to the fact that the Tx work is
stopped at the point where we cannot place one more buffer on the ring and
it is not restarted until cleanup is complete.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NIan Campbell <ian.campbell@citrix.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Cc: Greg Rose <gregory.v.rose@intel.com>
Cc: PJ Waskiewicz <peter.p.waskiewicz.jr@intel.com>
Cc: Alex Duyck <alexander.h.duyck@intel.com>
Cc: John Ronciak <john.ronciak@intel.com>
Cc: e1000-devel@lists.sourceforge.net
Cc: netdev@vger.kernel.org
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I'm removing NETIF_F_GRO from being initialed in the feature flags during
ixgbe_probe() bases on a comment from Michal Miroslaw
<mirq-linux@rere.qmqm.pl> that it is always set by network code now.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This consolidates setup code for multiple traffic classes in
the setup_tc routine.

Prep work to allow IEEE DCBX to optimize for number of traffic
classes. Also simplifies code paths.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

One existing call sites still expect either 4 or 8 traffic
classes to be specified. This fixes this allowing arbitrary
values up to 8 to work as expected.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change is meant to fix the patch:
	ixgbe: Cleanup FCOE and VLAN handling in xmit_frame_ring
And can be rolled into it if needed.

What this fixes is that VLAN tagged packets were not being tagged if they
were prio 7 which matches up with TC_PRIO_CONTROL.  In order to fix it I am
just setting things up so that we always tag VLAN tagged packets.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change makes it so that the CC bit in the descriptor is set when
SR-IOV is enabled.  This is needed in order to support offloading
functionality when passing traffic over the internal TX switch.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change converts the current bit array into a linked list so that the
q_vectors can simply go through ring by ring and locate each ring needing
to be cleaned.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch helps to simplify the work being done by the transmit path by
removing the unnecessary compares between count and the work limit.  Instead
we can simplify this by just adding a budget value that will act as a count
down from the work limit value.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change is meant to further cleanup the transmit path by streamlining
some of the VLAN and FCOE/DCB tasks in the transmit path.  In addition it
adds code for support software VLANs in the event that they are used in
conjunction with DCB and/or FCOE.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

CONFIG_FCOE is not the correct define to check since it is possible for it
to be CONFIG_FCOE_MODULE, as such the reference to it should be replaced
with IXGBE_FCOE.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch implements a partial refactor of the TX map/queue and cleanup
routines.  It merges the map and queue functionality and as a result
improves the transmit performance by avoiding unnecessary reads from memory.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

replace it by ndo_set_rx_mode
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use IFF_UNICAST_FTL to find out if driver handles unicast address
filtering. In case it does not, promisc mode is entered.

Patch also fixes following drivers:
stmmac, niu: support uc filtering and yet it propagated
	ndo_set_multicast_list
bna, benet, pxa168_eth, ks8851, ks8851_mll, ksz884x : has set
	ndo_set_rx_mode but do not support uc filtering
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Moves the Intel wired LAN drivers into drivers/net/ethernet/intel/ and
the necessary Kconfig and Makefile changes.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The way __ixgbe_notify_dca() was currently set up it would not be
possible to add a requester. Both cases of the IXGBE_FLAG_DCA_ENABLED
bit being on and off would lead to the function exiting for a
DCA_PROVIDER_ADD.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

after review of all intel drivers, found several instances where
drivers had the incorrect pattern of:
memory mapped write();
delay();

which should always be:
memory mapped write();
write flush(); /* aka memory mapped read */
delay();

explanation:
The reason for including the flush is that writes can be held
(posted) in PCI/PCIe bridges, but the read always has to complete
synchronously and therefore has to flush all pending writes to a
device.  If a write is held and followed by a delay, the delay
means nothing because the write may not have reached hardware
(maybe even not until the next read)
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>